User's Manual
Table Of Contents
- Revisions
- Reasons of change
- Introduction
- Regulations
- General installation guidelines
- (RF exposure)
- Compliance boundary definition
- Table of Contents
- 1. Introduction
- Scope of document
- Target Audience
- Reference manuals
- Conventions
- 2. Prior to Installation
- Topics
- Packing list materials
- Powering materials
- Power injectors
- Power cables
- Power modules & connectors
- Grounding materials
- Data traffic materials
- S-FTP cables
- Fiber optic cables
- SFP
- Pole fastening materials
- Mounting bracket
- Steel hose clamps
- Cable ties
- StreetNodeTM 6250 PTP(1)
- Outdoor DC PonE
- Outdoor AC PonE
- Indoor AC PoE
- Anchor point
- / /
- Introduction
- Site survey
- Preparation of the installation premises
- Network port distributors
- Cables routing (lamp post)
- Power cable routing
- Cable conduits
- Wall installation
- Installation location
- Lamp post or pole
- Grounding
- Outdoor grounding system
- Power supply source
- Circuit breakers
- Line Of Sight (LOS) verification
- Lightning & Surge protection
- Internal ovp(2)
- Safety
- Introduction
- Cable length restrictions
- Instruction
- Topics
- Equipment installation tools
- Ethernet cable termination tools
- Power supply cable termination tools
- Grounding cable termination tools
- 3. Installation of StreetNode 6250 PTP
- Mechanical Installation & Grounding
- Installation of Traffic Cable(s)
- Installation of Power Cable (Direct Powering)
- Installation of Power Injector (Power over Ethernet)
- Appendix A: Terminating Ethernet (S-FTP) Cable
- Appendix B: Terminating Power Supply Cable
- Appendix C: Terminating Grounding cable
- Appendix D: Removing StreetNode 6250 PTP
- Appendix E: Standards of Compliance
- Precautions
- Topics
- Tools and materials
- Lamp post (or pole) installation procedure
- Grounding cable installation procedure
- Topics
- Tools and materials
- Ethernet (S-FTP) cable installation procedure
- Ethernet (S-FTP) cable installation with SFP
- Ethernet (S-FTP) cable installation with SFP
- Topics
- Tools and materials
- Procedure
- Introduction
- Topics
- Tools and materials
- Mechanical and cabling installation (PonE)
- Cabling installation (PoE)
- Introduction
- Parts of RG-45 jack
- Termination procedure
- Procedure
- Topics
- Procedure
Chapter 2. Prior to Installation
34
Cable Length Restrictions, Continued
Cable length
restrictions
A): Maximum length of cables used for Data Traffic:
Given that the maximum line rate of each traffic interface supported by
StreetNode
TM
6250 PTP is 1Gbps Ethernet and depending on the type of
cable used for data traffic, the following restrictions apply to the lengths of
traffic bearing cables:
• Cat5E or Cat6 S-FTP cable:
The total length of Gigabit ETHERNET (S-FTP) cable up cannot exceed 100
meters, where total length of cable is defined as: length of cable between
StreetNode
TM
6250 PTP radio unit receptacle up to power injector receptacle
(out) PLUS length of cable between power injector receptacle (in) up to
customer network equipment receptacle.
• Multimode optical fiber cable (Combined with 1000Base-LX SFP):
OM1 (62.5/125) Multimode cable type combined with 1000Base-SX (850nm)
SFP: Max length 275m
OM2 (50/125) Multimode cable type combined with 1000Base-SX (850nm)
SFP: Max length 550m
• Single mode optical fiber cable:
Combined with 1000Base-LX SFP : Max length 5km
Combined with 1000Base-LX10 SFP : Max length 10km
Combined with 1000Base-EX SFP : Max length 40km
Combined with 1000Base-ZX SFP : Max length 80km
Continued on next page