INSTRUCTION MANUAL AND WARRANTY
THANK YOU FOR CHOOSING AN INVICTA TIMEPIECE IMPORTANT THINGS TO KNOW These timepieces have been tested for water resistance. In order to maintain the water resistance, be sure to always close the crown tightly after setting. Screw Down Crowns: Many Invicta watches are equipped with a screw down crown to help prevent water infiltration. This is most common on our Diver models.
QUARTZ, AUTOMATIC, AND MANUAL WIND WATCHES A Quartz Watch is battery powered and does not require winding. Eventually the battery will need to be replaced. QUARTZ, AUTOMATIC, AND MANUAL WIND WATCHES Display Elements Control Buttons An Automatic Watch is a mechanical watch that winds itself and does not require a battery. When worn daily, the movement of your wrist causes the mainspring to wind progressively, eliminating the need for additional winding.
WHAT DOES THIS INDICATE? Many Invicta watches are equipped with features that go beyond the telling of time and date. These functions are displayed on what are called subdials, indicators, counters or zones. Your watch may have one or more of these. Knowing them will be useful when identifying which instructions pertain to your watch. ! PLEASE NOTE . Since dial designs and shapes vary, not all subdials are perfectly round, or positioned in the same place.
WHAT DOES THIS INDICATE? WHAT DOES THIS INDICATE? 24-Hour: often called a GMT or second time zone indicator, the hand of this counter makes a full rotation in a 24-hour period, thereby also indicating whether it is a.m. or p.m. It is often coupled with a Sun/Moon display. Sun/Moon: indicates a.m. or p.m. through the display of the sun or moon. It is often coupled with a 24-hour indicator.
WHICH INSTRUCTIONS SHOULD I READ? Invicta crafts many styles of watches using a variety of fine movements and complications. To find the instructions for your particular timepiece, simply look at it and answer one of the following questions: Does it tell time only? ........................................................................ 10 Does it tell time and date? ............................................................... 12 Does it tell time, day and date? ..........................................
WATCHES WITH TIME ONLY Setting the Time WATCHES WITH TIME ONLY Display Elements Control Buttons 1. Pull out the crown to position 1. The watch stops. 2. Turn the crown until the correct time appears. 3. Push the crown back into position 0. The watch will begin running again.
WATCHES WITH TIME AND DATE Setting the Time and Date WATCHES WITH TIME AND DATE Display Elements Control Buttons 1. Pull out the crown to position 1. The watch stops. 2. Turn the crown until you reach the correct date. 3. Pull out the crown to position 2. 4. Turn the crown until you reach the correct time. 5. Push the crown back into position 0. The watch will begin running again.
WATCHES WITH TIME, DAY AND DATE Setting the Time, Day and Date WATCHES WITH TIME, DAY AND DATE Display Elements Control Buttons 1. Pull out the crown to position 1. 2. Turn the crown clockwise until you reach the correct day. 3. Turn the crown counter clockwise until you reach the correct date. 4. Pull out the crown to position 2. 5. Turn the crown until you reach the correct time. 6. Push the crown back into position 0. The watch will begin running again.
WATCHES WITH ALARM WATCHES WITH ALARM Setting the Time and Date Display Elements Control Buttons 1. Pull out the crown to position 1. The watch continues to run. 2. Turn the crown until yesterday’s date appears. 3. Pull out the crown to position 2. The second hand stops. The display changes from alarm time to reference time. 4. Turn the crown until the correct date appears. Observe AM/PM clock rhythm. 5. Continue to turn the crown until the correct time appears. 6. Push the crown back into position 0.
WATCHES WITH ALARM Setting the Reference Time Parallel to the current time, the reference time runs in the background: the alarm time refers itself to this reference time. Thus, resetting the time also requires the identical correction of the reference time.If the reference time is not synchronized with the current time, this results in the alarm signal being emitted at a different time than the set alarm time. 1. Pull out the crown to position 2. The second hand stops.
WATCHES WITH ALARM Setting the Alarm 1. Press the push-button for at least 2 seconds. Until the small minute hand jumps forward one minute and setting mode is activated. Short pressing: Less than 1 second: The reference time is moved forward by the minute. Medium pressing: 1-2 seconds: The reference time is moved forward by the hour. Long pressing: Longer than 2 seconds: The reference time is moved forward until the push-button is released. 2. Switch alarm ON/OFF: Press the push-button briefly.
CHRONOGRAPHS Built-in stopwatch feature CHRONOGRAPHS Display Elements Control Buttons A chronograph is a timepiece with a built-in stopwatch feature. With few exceptions, Invicta chronographs tell the time, date and include three subsidiary dials. These dials are often referred to as sub-dials, indicators, counters, eyes or zones. Typically, they measure minutes, seconds and tenths of a second. The sub-dials that measure minutes and tenths of a second are part of the stopwatch feature.
CHRONOGRAPHS CHRONOGRAPHS Setting the Time and Date . After a Battery Change 1. Pull out the crown to position 1. The watch continues to run. 2. Turn the crown until you reach yesterday’s date. If you are setting the date between 9pm and 12pm, the date must be set to the following day as dates set between these hours do not automatically change at midnight. 3. Pull out the crown to position 2. To set the time to the exact second, it must be pulled out when the second hand is in position 0.
CHRONOGRAPHS Adjusting the Chronograph Hands to Zero Position 1. Pull out the crown to position 2. All three chronograph hands are in their correct or incorrect zero position. 2. Keep push-button A and B depressed simultaneously for at least 2 seconds. The center stop-second rotates 360º and corrective mode is activated.
CHRONOGRAPHS CHRONOGRAPHS Measuring Accumulated Time Measuring Intermediate Time 1. Start: Press push-button A. Start timing. 1. Start: Press push-button A. Start timing. 2. Stop: Press push-button A. 2. Display interval: Press push-button B. Timing continues in the background. 3. Restart: Press push-button A. Timing is resumed. 4. Stop: Press push-button A. Final time is displayed. Accumulation of timing can be continued by pressing push-button A. 5. Reset: Press push-button B.
CHRONOGRAPHS CHRONOGRAPHS Setting the Time Setting the Date . Quick Mode 1. Pull out the crown to position 2. To set the time to the exact second, it must be pulled out when the second hand is in position 0. The watch stops. 1. Pull out the crown to position 1. The watch continues to run. 2. Turn the crown until you reach the correct time. 3. Push the crown back into position 0. To set the time to the exact second, it must be pushed back into position 0 at the exact second. 3.
CHRONOGRAPHS WITH BIG DATE AND DAY Invicta is one of the first companies to use the Swiss-made Startech 5050.C, the world’s first big date and day chronograph with three eyes. It features small seconds at 3 o’clock, tenths of a second at 6 o’clock, and 30 minutes and, in some, 12 hours at 9 o’clock.
CHRONOGRAPHS WITH BIG DATE AND DAY CHRONOGRAPHS WITH BIG DATE AND DAY Setting the Time, Day and Date 1. Pull out the crown to position 1. Basic Function . Start/Stop/Reset 2. Turn the crown until you reach the correct date. If you change the date between 9:00pm and 12:00pm, it must be set to the following day as dates set between these hours do not automatically change at midnight.
CHRONOGRAPHS WITH BIG DATE AND DAY Adjusting the Chronograph Hands to Zero Position CHRONOGRAPHS WITH BIG DATE AND DAY Adjusting the Chronograph Hands to Zero Position Before using the chronograph functions, please ensure that the crown is in position 0 and the 4 chronograph hands are precisely at zero position following activation of push-button B. Should this not be the case, the positions of the hands must be adjusted. To adjust the next hand: Press push-button B. 1. Pull out the crown to position 1.
CHRONOGRAPHS WITH BIG DATE AND DAY Measuring Elapsed Time 1. Start: Press push-button A. The center sweep hand will begin measuring seconds. 2. Stop: Press push-button A and read how much time has elapsed. 3. Reset: Press push-button B. The chronograph hands will be reset to their zero positions. ! PLEASE NOTE . The center sweep hand should be used only as a function of the chronograph and should not be kept running constantly in place of the small seconds.
CHRONOGRAPHS WITH BIG DATE AND DAY Measuring Accumulated Time CHRONOGRAPHS WITH BIG DATE AND DAY Measuring Intermediate Time 1. Start: Press push-button A. The center sweep hand will begin measuring seconds. 1. Start: Press push-button A. The center sweep hand will begin measuring seconds. 2. Stop: Press push-button A. Read the 3 chronograph counters. 2. Stop: Press push-button B. This will indicate intermediate time. 3. Resume timing: Press push-button A again. 3.
CHRONOGRAPHS WITH DATE, DAY AND MONTH Setting the Time, Date, Day and Month CHRONOGRAPHS WITH DATE, DAY AND MONTH Display Elements Control Buttons 1. Pull out the crown to position 1. The watch stops. 2. Turn the crown until you reach the correct time. 3. Push the crown back into position 0. To set the time to the exact second, it must be pushed back in at the exact second. Please observe AM/PM clock rythm. The watch will begin running again. 4. Press the corrector C until you reach the correct date.
CHRONOGRAPHS WITH DATE, DAY AND MONTH CHRONOGRAPHS WITH DATE, DAY AND MONTH Setting the Time, Date and Day 1. Pull out the crown to position 1. Basic Function . Start/Stop/Reset 2. Turn the crown until you reach the correct date. If you change the date between 9:00pm and 12:00pm, it must be set to the following day as dates set between these hours do not automatically change at midnight.
CHRONOGRAPHS WITH DATE, DAY AND MONTH Adjusting the Chronograph Hands to Zero Position CHRONOGRAPHS WITH DATE, DAY AND MONTH Adjusting the Chronograph Hands to Zero Position Before using the chronograph functions, please ensure that the crown is in position 0 and the 4 chronograph hands are precisely at zero position following activation of push-button B. Should this not be the case, the positions of the hands must be adjusted. To adjust the next hand: Press push-button B. 1.
CHRONOGRAPHS WITH DATE, DAY AND MONTH CHRONOGRAPHS WITH DATE, DAY AND MONTH Measuring Accumulated Time Measuring Intermediate Time 1. Start: Press push-button A. Start timing. 1. Start: Press push-button A. Start timing. 2. Stop: Press push-button A. 2. Display interval: Press push-button B. Timing continues in the background. 3. Restart: Press push-button A. Timing is resumed. 4. Stop: Press push-button A. Final time is displayed. Accumulation of timing can be continued by pressing push-button A.
WARRANTY INFORMATION Your Invicta timepiece is backed by a comprehensive 1-year Warranty from date of purchase. This covers repairs due to failure or breakdown of the movement and all its components, as well as the crown, dial, markers, hands and water resistant pressure. It does not cover scratches to the crystal, case, metal band, leather, microfiber, or rubber straps or any damage that results from normal wear and tear.
WARRANTY INFORMATION WARRANTY INFORMATION Invicta watches are designed to withstand the most demanding conditions for a very long time. Every care is taken to ensure that your watch meets the highest standards before it leaves the workshop. technician designated to repair or overhaul your watch find it necessary to re-submit the watch into observation, your watch will be tested and observed for one more week.
SHIPPING INFORMATION ! PLEASE NOTE: If you are sending your watch to the Invicta Service Center and it has an exotic strap, you must remove the strap first, or we cannot accept the shipment. It will be returned to you. The strict laws of the U.S. Government Fish and Wildlife Service prohibit the shipping of exotic species without proper documentation. This includes alligator, crocodile, snake, Ostrich, and fish, such as stingrays or Salmon.
SHIPPING INFORMATION ! PLEASE NOTE: The owner will be responsible for shipping the watch to and from us for service. A flat rate of $25 will be charged, which should be submitted as a money order. MAIL TO: Visit our website. Invicta Service Center 1 Invicta Way (3069 Taft St.) Hollywood Florida, 33021 U.S.A. As part of our commitment to superior service, once your watch is received, we will mail you a postcard advising you of your service case number.
© Invicta Watch Company of America, Inc., 2008. All rights reserved. www.invictawatch.
