Installation Guide

ManualsBrandsInvisiDoor ManualsDoors & Windows32 in. x 80 in. Unfinished Cherry 4-Shelf Bookcase Interior Door Slab

INSTRUCTION MANUAL

for Installing

INVISIDOOR HINGE KIT

ID.HINGEKIT

The Invisidoor Hinge Kit is designed and manufactured in the USA and offers:

• Easy installation; comes complete with detailed Installation Instructions.

• Universal design; can be used for inswing or outswing, left-hand or right-hand doors

• Durable powder-coated ¼” thick steel hinge plates

• Adjustable support foot

• Quiet, smooth pivoting action

• All fasteners included

• (Bookcase not included)

Closed InswingOutswing

Summary of content (8 pages)

PAGE 1
INSTRUCTION MANUAL for Installing INVISIDOOR HINGE KIT ID.HINGEKIT Outswing Closed Inswing The Invisidoor Hinge Kit is designed and manufactured in the USA and offers: • • • • • • • Easy installation; comes complete with detailed Installation Instructions.
PAGE 2
Instruction Manual for InvisiDoor Hinge Kit Installation Installation Tools Needed: Hinge Kit Includes: Ø10 Ø8 Ø19 Ø10 Ø3 3/8” Allen Ø8 Ø19 Ø3 3/32” (Outswing) 5/8” Ø10 Ø12 1/4” Allen Ø10 (Inswing) Ø12 OR Wall Opening Preparation 1. Check the opening into which the Invisidoor will be installed to verify that it is plumb and level. Correct operation and appearance of the Invisidoor requires that the opening be level and plumb or you need to make accommodations for it. 2.
PAGE 3
Top of Bookcase Top of Bookcase Approx. 15/16” Face Frame centered on bookcase 3/4” Overhang Face Frame 3/4” Plywood Sides 1/4” Rabbetted 1/2” Plywood Back Inside Bottom of Bookcase • • • Bottom shelf of the bookcase is 1/8” below the top edge of the bottom face frame rail. 1/8” Lip Sides and back run down past the bottom shelf, but not as far as the face frame (forms a pocket on the bottom of bookcase. Sides and back extend ¾” below the bottom shelf.
PAGE 4
Hinge Plate #1 Bottom of the bookcase Hinge Plate #3 With attached pivot pin and washers, mounted onto the threshold Pivot Hinge Installation Use the diagrams to identify locations for the pivot hinge to be installed on the left or right side of the unit as either an outswing (which pulls out toward the bookcase side) or an inswing (which rotates away from the bookcase side). In most cases, the bookcase face frame will be flush with the drywall.
PAGE 5
2. To install hinge plate #4 to the upper jamb. • Shim the jamb as needed at location of pivot hinge for a solid mounting area between the upper jamb and the door header. The longer 2 1/4” screws will be used to solidly secure this hinge plate through the jamb and into the header once the bookcase is in its proper location. Outswing Inswing Hinges to Bookcase Installation 1.
PAGE 6
Bookcase Installation • • • • • • • Lift the bookcase into the opening. Inswing bookcase: mounts from the inside of the opening Outswing bookcase: mounts from the outside of the opening Set the hinge plate located on the bottom of the bookcase onto the pin of the hinge plate located on the threshold/floor. Be sure the washers are in place. Align the upper hinge plate located on the top of the bookcase (hinge plate #2) with the upper hinge plate located on the header (hinge plate #4).
PAGE 7
Outswing Outswing bookcase: • Trim on the hinge side of the bookcase and the top will be attached to the wall, but the non-hinged side trim will be attached to the bookcase to act as a stop. • It is recommended that the trim overlay the face frame by 3/4” and be mounted very securely to withstand the opening and closing of the door. • The trim across the top of the door must be mounted to allow clearance for the door to swing below it.
PAGE 8
REV. 4.12.