User Manual USB VGA KVM Console Extender GCE500U PART NO. M1125-b www.iogear.
Table of Contents Package Contents 4 System Requirements 5 Overview 6 Rack Mounting 9 Grounding 11 Standard Installation 12 Advanced Installation 16 Operating Modes 20 LED Indications 21 Federal Communications Commission (FCC) Statement 22 CE Statement 23 SJ/T 11364-2006 24 Limited Warranty 25 Contact 26 3
Package Contents 1 x GCE500U Local Unit 1 x GCE500U Remote Unit 1 x USB KVM Cable 2 x Rack Mount Kit 2 x Grounding Cable 2 x Power Adapter 1 x Installation Guide 1 x Warranty Card 4
System Requirements - A Solid CAT5e/6 Cable Console - VGA, SVGA, SXGA, UXGA, WUXGA or Multisync monitor - USB Keyboard and mouse Computer - VGA, SVGA, SXGA, UXGA, WUXGA or Multisync video output - An available USB port 5
Overview Front View 1. 2. 3. 4. 5. 6.
Rear View 1. 2. 3. 4. 5.
Side View 1.
Rack Mounting Step 1 Unscrew the screws that are in the bottom of the housing, then screw the provided mounting bracket on top of the units with the screws.
Step 2 Screw the other side of the bracket onto any available area on the rack.
Grounding To prevent damage to your installation, it is important that your devices are properly grounded. Use the provided grounding wires to ground the Local and Remote Unit of the GCE500U. Connect one end of the wire to the grounding terminal and the other end of the wire to a suitable grounded object.
Standard Installation Note: Please make sure your computer is completely shutdown before you begin. Step 1 Connect the power adapter between the wall outlet and the unit (Both local and remote units).
Step 2 Connect the provided USB KVM Cable between the local unit’s CPU port and the computer.
Step 3 Connect your VGA monitor to the console VGA port, USB keyboard and mouse to the Console USB keyboard and mouse port respectively (Both local and remote units). Note: Please connect and set the local monitor to the same resolution as the remote monitor.
Step 4 Connect your CAT5e/6 Cable between the Extension Input/Output Ports from the local and remote unit. Final Step Turn on your computer and monitors.
Advanced Installation Note: Please make sure your computers are completely shutdown before you begin. Step 1 Connect the power adapter between the wall outlet and the unit (Both local and remote units).
Step 2 Connect the provided USB KVM Cable between the local unit’s CPU port and the console VGA and keyboard port of the KVM. (KVM example: IOGEAR’s GCS1734 ) Step 3 Please refer to the user manual of the specific KVM to complete the KVM installation. Note: Please ignore the Console VGA, USB Keyboard and mouse ports installation steps from the KVM’s user manual because you have done this portion from the last step (Step 2).
Step 4 Connect your VGA monitor to the console VGA port, USB keyboard and mouse to the Console USB keyboard and mouse port respectively (Both local and remote units).
Step 5 Connect your CAT5e/6 Cable between the Extension Input/Output Ports from the local and remote unit. Final Step Turn on your computers and monitors.
Operating Modes Mode Description Local Only local console has access Remote Only remote console has access Note: Remote Mode cannot be selected by the Operating Mode Pushbutton, it only occurs when Auto Mode grants the access to the remote console. Auto (Default) Either local or remote console can have access, but only one console can have access at a time.
LED Indications LED Status Description Local LED ON Remote LED OFF Local Mode Local LED OFF Remote LED ON Remote Mode Both Local and Remote LED flash Auto Mode Link LED ON Extension connection is established Link LED flashes Extension connection is not established 21
Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential setting. This product generates, uses, and can radiate radio frequency energy and, if not installed and used as directed, it may cause harmful interference to radio communications.
CE Statement This device has been tested and found to comply with the requirements set up in the council directive on the approximation of the law of member states relating to EMC Directive 89/336/EEC, Low Voltage Directive 73/23/EEC and R&TTE Directive 99/5/EC. The product has been approved for LVD and covered the following countries: Belgium, Denmark, France, Germany, Italy, Portugal, U.K.
SJ/T 11364-2006 有毒有害物质或元素 部件名称 镉（Cd） 六价 (Cr(VI)) 多溴联苯 （PBB） 多溴二苯醚 （PBDE） 铅 (Pb) 汞 (Hg) 电器部件 ● ○ ○ ○ ○ ○ 机构部件 ○ ○ ○ ○ ○ ○ ○:表示该有毒有害物质在该部件所有均质材料中的含量均在SJ/T 11363-2006规定的限量要求之下。 ●:表示符合欧盟的豁免条款，但该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006的限量要求。 ×: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出SJ/T 11363-2006的限量要求。 24
Limited Warranty IN NO EVENT SHALL THE DIRECT VENDOR’S LIABILITY FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE PRODUCT, DISK, OR ITS DOCUMENTATION EXCEED THE PRICE PAID FOR THE PRODUCT. The direct vendor makes no warranty or representation, expressed, implied, or statutory with respect to the contents or use of this documentation, and especially disclaims its quality, performance, merchantability, or fitness for any particular purpose.
Contact IOGEAR www.iogear.com iogear.custhelp.com support@iogear.
©2017 IOGEAR®
