Installation Guide eSATA 1.5 Gbps 2-port Cardbus Card GPS702W6 1 PART NO.
Table of Contents Introduction 4 Features 5 Package Contents 6 Software Installation 7 Federal Communications Commission (FCC) Statement 11 CE Statement 13 Limited Warranty 14 Contact 15 3
Introduction This Serial ATA 2 Port CardBus Host Adapter is a 32bit CardBus card with dual fully compliant Serial ATA ports. The SATA port can access SATA storage media such as: Hard drives, CD-RWs, DVD-ROMs and DVD-RAM drives. The board supports a 32-bit PC Card interface and a Serial ATA Generation 1 at transfer rate of 1.5 Gb/s.
Features PC Card Interface • Integrated DMA engines. • 32 bit CardBus fully compliant. High Speed Serial ATA Interface • Dual high speed Serial ATA interface ports, each supporting 1st generation Serial ATA data rates (1.5Gb/s). • Fully compliant with Serial ATA 1.0 specifications. • Supports Spread Spectrum in receiver. • Independent 256-byte FIFOs (32 bit * 64 deep) per Serial ATA channel for host reads and writes.
Package Contents • Serial ATA 2 Port CardBus Host Adapter • Quick Start Guide • Driver CD 6
Software Installation To use this CardBus adapter, the host computer must be equipped with one free PCMCIA Card Type II or Type III slot. This section provides the information on how to install the drivers for the Serial ATA 2 Port CardBus Host Adapter within Windows.
Windows XP installation 1 Insert the Serial ATA 2 Port CardBus into an available CardBus slot. Connect the serial ATA cable(s) between the Serial ATA 2 Port CardBus and the serial ATA device(s). 2 Windows will display the ‘Found New Hardware Wizard’. Click ‘Next’. 3 Insert the Driver CD into your CD-ROM/DVD Drive. 4 Select “Install from a list or specific location (Advanced)”, and click “Next”.
5. Specify the Driver CD location and click Next. 6. Points the wizard to [CD Drive Letter]:\ SATA NonRaid_2Port\Sil3x12 \Win98_me _2000_xp_nt4.0 \Driver, click Open then OK. 7. When the wizard indicates that it found a driver for the device click ‘Next’. 8. The wizard will now copy the required files to the system and initialize the driver. After starting the driver the wizard will display a completion dialog, click ‘Finish’ to exit the wizard.
Verifying Windows XP Installation 1. Right click on the ‘My Computer’ icon, select ‘Properties’, left click on the ‘Hardware’ tab, and select the ‘Device Manager’ button. 2. Double click on ‘SCSI and RAID Controllers’, if there is no yellow ‘!’ or ‘?’ in front of ‘Silicon Image SiI 3x12 SATALink Controller’ the driver is functioning properly.
Federal Communications Commission (FCC) Statement Federal Communications Commission (FCC) Statement 15.21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. 15.105(b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: 1. this device may not cause interference and 2. this device must accept any interference, including interference that may cause undesired operation of the device.
CE Statement This device has been tested and found to comply with the requirements set up in the council directive on the approximation of the law of member states relating to EMC Directive 89/336/EEC, Low Voltage Directive 73/23/EEC and R&TTE Directive 99/5/EC.
Limited Warranty The manufacturer, IOGEAR, makes NO warranty or representation, whether express or implied, regarding the contents, use or suitability of this software, disk or documentation. IOGEAR specifically disclaims any and all warranties regarding the quality and performance of this software, disk or documentation including, but not limited to the implied warranty of merchantability and implied warranty of fitness for a particular purpose.
Contact Toll Free: (866) 9-IOGEAR Phone: (949) 453-8782 23 Hubble Irvine, CA 92618 USA www.iogear.com support@iogear.com ©2007 IOGEAR. All Rights Reserved. PART NO. M0555 IOGEAR, the IOGEAR logo, MiniView, VSE are trademarks or registered trademarks of IOGEAR, Inc. Microsoft and Windows are registered trademarks of Microsoft Corporation. IBM is a registered trademark of International Business Machines, Inc. Macintosh, G3/G4 and iMac are registered trademarks of Apple Computer, Inc.
About Us FUN IOGEAR offers connectivity solutions that are innovative, fun, and stylish, helping people enjoy daily life using our high technology products. GREEN IOGEAR is an environmentally conscious company that emphasizes the importance of conserving natural resources. The use of our technology solutions helps reduce electronic waste. HEALTH IOGEAR supports healthy and fit lifestyles. By integrating products with the latest scientific developments, IOGEAR’s solutions enhance the life of end-users.