Quick Start Guide USB to Serial Adapter GUC232A PART NO. Q0248 www.iogear.
1 Package Contents 1 USB to Serial Adapter 1 Installation CD-ROM 1 Quick Start Guide 1 Warranty Card System Requirements Macintosh • Mac OS X 10.2 or Later • Available USB Port • CD-ROM PC • Windows® XP/Vista/7/8/8.1* • Available USB Port • CD-ROM Overview • Full Compliance with USB specification v1.
Windows Installation Procedure 2 For Windows XP/Vista/7/8/8.1 Note: Please do not plug in the USB to Serial Adapter until after you have completed the following instructions. 1. Insert the IOGEAR Installation CD-ROM into your computer. 2. You will see the README for the IOGEAR installation CD-ROM. 3. After you click Continue, you will be presented with the End User Agreement of the IOGEAR USB to Serial Adapter. It is strongly suggested that you read in the End User Agreement in its entirety.
3 4. You will now begin the installation procedure. Click Start. 5. The installation procedure will begin. 6. You have finished installing the drivers for your IOGEAR USB to Serial Adapter. To Configure your Serial Device: 1. Open device manager on your Windows computer or laptop. 2. Expand the Ports (COM & LPT) tab. You should see your device listed as an ATEN USB to Serial Bridge assigned to a COM Port. 3. To configure your serial device, right click on this device and select Properties.
Mac OS X Installation Procedure 10.2 or Later Please contact technical support for the latest Mac drivers Note: Please do not plug in your IOGEAR USB to Serial Adapter until after you have completed the below instructions. 1. Insert the IOGEAR CD-ROM into your Mac. You will see the IOGEAR CD on your Desktop. 2. Double-click the IOGEAR Logo, you will see the CD-ROM Contents. 3. Double-click the Mac OS 10 folder. 4. You will now see the Extensions Package for Mac OS X. 5. Double-click the PL2303_1.0.8.pkg.
Mac OS X Installation Procedure 6. The USB to Serial Cable driver installation will appear. Click Continue. 7. You will now be asked where you would like to install the driver package. Select the Hard Disk that contains your Mac OS X (or "10") partition, then click Continue. 8. You will now be asked if you wish to perform a basic installation of the software package on your Mac OS X volume. Click Install.
6 9. You will now be asked for your Mac OS X login password. This is the password used when setting up your Macintosh computer. If you do not know what it is, please contact your network administrator. Once you have entered your password, click OK. 10. A small prompt will appear, letting you know that your computer will be restarted after installation has been completed. Click Continue Installation.
7 11. Once the installation procedure is completed, click Restart. Configuring your Serial Device: Go to the Settings, Preferences, or Setup of the software you are using with your device and check which port is selected; you will want to change it to the "USB serial-port". Note: If you are having issues configuring your device, try restarting your computer.
FCC Statement The user is cautioned that this device should be used only as specified within this manual to meet RF exposure requirements. Use of this device in a manner inconsistent with this manual could lead to excessive RF exposure conditions. CE Statement This device has been tested and found to comply with the following European Union directives: Electromagnetic Capability (2004/108/EC), Low Voltage (2006/95/EC) and R&TTED (1999/5/EC).
Limited Warranty WE’RE HERE TO HELP YOU! NEED ASSISTANCE SETTING UP THIS PRODUCT? Make sure you: 1. Visit www.iogear.com for more product information 2. Visit www.iogear.com/support for live help and product support Warranty Information This product carries a 1 Year Limited Warranty. For the terms and conditions of this warranty, please go to http://www.iogear.com/support/warranty Register online at http://www.iogear.com/register Important Product Information Product Model Serial Number Contact iogear.
