Hi-Speed USB 2.0/FireWire® Combo PCI Card GUF320 Quick Start Guide Read this guide thoroughly and follow the installation and operation procedures carefully to prevent any damage to the unit and/or any of the devices it connects to. GUF320 package contains: 1 Hi-Speed USB 2.
1. Welcome Thank you for purchasing IOGEAR’s Hi-Speed USB 2.0/FireWire® Combo PCI card! Once again, IOGEAR brings the cutting-edge technology of today and tomorrow to your Macintosh or PC. You will enjoy the convenience and high-speed that has made these technologies industry-standard. Note: Your order has been carefully packaged and inspected, and we hope you are pleased with the IOGEAR product you purchased.
2. Hardware Requirements Minimum System Requirements Macintosh • PowerMac G3 (Blue & White Tower) or later • Mac OSX 10.1.5 or higher is required for USB 2.0 functionality • 64MB of RAM • Available PCI Slot PC • Pentium® or K6® – class processor (266Mhz or higher) • Windows 98 Second Edition or later • 64MB of RAM • Available PCI Slot Recommended System Requirements Macintosh • PowerMac G4 1.0Ghz or higher • Mac OSX 10.2.
. Installing the Combo PCI Card Warning! Carelessness in installing this device can result in permanent damage to your computer, and will void your warranty. Please use care any-time you open your Mac or PC and follow the manufacturer’s guidelines for proper handling proceedures. Win 98SE and ME users, please proceed to the next page for instructions on installing the needed software prior to installing the PCI card. Step.
Step. 6 Use a non-magnetic screwdriver to unscrew and remove the PCI slot's metal cover. Step. 7 Slide the IOGEAR Hi-Speed USB 2.0/FireWire Combo Card into the open PCI ® slot. Step. 8 Install the locking-screw to secure the IOGEAR Hi-Speed USB 2.0/FireWire ® Combo Card into the computer, then close the computer case. 5. Software Installation FOR WINDOWS® 98SE & ME Step.
Step. 2 • Open My Computer • Open the IOGEAR CD • Open the GUF320 folder • Double-click the Installation file Step. 3 The installation procedure will begin. Once it has finished, click the “Restart Later” radio button, then click Finish. Step. 4 Remove the IOGEAR CD-ROM from your computer and insert your Windows CDROM. Step. 5 Shut-down your computer, leaving the Windows CD-ROM inside your computer. Step. 6 It is now time to install the PCI card into your computer.
Step. 10 You will now be asked where to find these illustrious drivers. Uncheck all boxes (Floppy, Hard Drive, Windows Update, etc.) except CD-ROM, then click Next. Step. 11 Windows will find the drivers on the Windows CD-ROM, then proceed to ask you “Which driver do you wish to install?” Since the Ali PCI to USB Open Host Controller driver is already selected, we can safely click Finish. Step. 12 This process will repeat 3 times – This process will repeat 3 times - This process will repeat 3 times.
FOR WINDOWS® 2000 & XP Your Windows 2000/XP operating system natively supports the USB 2.0/FireWire® Combo PCI card – No drivers are necessary! However, please ensure you have the latest Service Packs installed… • Windows 2000 – Service Pack 2 or later • Windows XP – Service Pack 1 or later FOR MACINTOSH – OSX 10.1.5 AND ABOVE The USB 2.0/FireWire® Combo PCI card is natively supported within the OSX operating system, with the exception of USB 2.0 functionality.
6. Radio and TV Interference This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
