Configuration Utility 802.1X : Accept normal clients and work simultaneously with RADIUS Server. The encryption key is got from RADIUS Server dynamically. • Encryption Key Length You can select either 64 bits or 128 bits. • RADIUS Server IP The 802.1X server’s IP address. • RADIUS port The 802.1X server’s service port. • RADIUS Shared Key Key value shared by the RADIUS server and this router. This key value is consistent with the key value in the RADIUS server.
Configuration Utility WPA-PSK : Accept WPA clients only and Pre-share key (encryption key) must be entered manually. You can input either 8 to 63 ASCII characters or 64 Hexadecimal digits as Pre-share key. • Pre-share Key Mode Either ASCII or HEX can be selected. • Pre-share Key Please input either 8 to 63 ASCII characters or 64 Hexadecimal digits as Pre-share key.
Configuration Utility WPA : Accept WPA clients only and work simultaneously with RADIUS Server. The encryption key is got from RADIUS Server dynamically. • RADIUS Server IP The 802.1X server’s IP address. • RADIUS port The 802.1X server’s service port. • RADIUS Shared Key Key value shared by the RADIUS server and this router. This key value is consistent with the key value in the RADIUS server. Note: If you enable 802.1X or WPA feature, you must also have a RADIUS Server ready.
Configuration Utility Description: • WEP Encryption: The WEP encrypts frames transmitted through wireless module using preentered WEP key. You can configure 4 key sets, and select one of them to apply. Note: To complete the WPA operation, you also need to enable the WPA client at the wireless client site (the computer running wireless client’s devices, such as the GWP514 Cardbus card GWP514 Cardbus Card or GWU523 USB adaptor).
Configuration Utility After installed, the Windows WPA Client will update the wireless network configuration dialog boxes to support new WPA options. 1. Click Connect To>Wireless Network Connection to bring up the dialogue window of Wireless Network Connection Status. Click the Properties box to bring up next dialogue window. 2.
Configuration Utility 3. Set up your WPA configuration by selecting the Network Authentication mode and Data encryption, and input same Network key as you input at the Wireless-G Broadband Gateway.
Configuration Utility network, but.only the wireless clients with the same WEP key can to communicate on the wireless network. Enhanced Setting SSID broadcast If the option is enabled, the SSID of the AP could be seen in the site survey of wireless client’s utility. If the option is disabled, the SSID of the AP will not be seen in the wireless client’s utility.
Configuration Utility The Wireless Distribution System (WDS) provides wireless point-to-point bridging, and point-tomultipoint bridging for deployment over large area. With the WDS feature, the WLAN coverage range can be easily extended. WDS Setting Wireless Bridging The wireless bridging feature can be enabled by setting the mode to Enable. The default setting is Disable, only access point function is available.
Configuration Utility Associated Client List It displays information of stations that are currently associated to your wireless router. You can check who are linking to your network, for security and activity monitoring purposes. Click Refresh button to update the list.
Configuration Utility Internet Page In Internet Settings, you can configure the way your Wireless-G Broadband Router uses to connect to your ISP.
Configuration Utility Connection Type It allows you to configure the way you connect to your ISP. This Wireless Broadband Router can be connected to your ISP in any of the following ways: DHCP Client, PPPoE, Static IP, L2TP and Dynamic IP. 48 • DHCP Client: Enter the Host Name if your ISP provides it; otherwise, just leave it blank.
Configuration Utility • Dynamic IP - PPPoE: Complete User name, password, confirm password fields. • Static IP: Complete the IP address, subnet mask, ISP gateway and primary DNS fields.
Configuration Utility • Dynamic IP - PPTP: Complete fields on this screen. Those information can get from your ISP.
Configuration Utility MAC Clone If your ISP restricts connections to pre-registered computers only, use the MAC Clone feature to copy your computer’s Media Access Control (MAC) address to your wireless broadband router. This procedure will cause the Wireless-G Broadband Router to appear as a single computer. To do MAC Clone: click Clone MAC.
Configuration Utility Virtual Computers Virtual Computer enables you to use the original NAT feature, and allows you to setup the one-toone mapping of multiple global IP address and local IP address. • Global IP: Enter the global IP address assigned by your ISP. • Local IP : Enter the local IP address of your LAN PC corresponding to the global IP address.
Configuration Utility Dynamic DNS This feature enables you to run your domain (ex. www.mywebsite.com) over a changing IP. Before you can use this feature, you need to sign up for DDNS service from one of the Dynamic DNS providers that this Wireless-G Broadband Router supports and fill in related fields to make it work. You may follow the following steps to enable this function. • Sign up for DDNS service and write down the host name, user name and password.
Configuration Utility Security Your IOGEAR Wireless-G Broadband Router features powerful and flexible firewall protection to keep your computer and/or network secure. If you are an advanced user, you can configure firewall policies depending on your needs.
Configuration Utility Packet Filter Packet Filter enables you to control what packets are allowed to pass the router. Outbound filter applies on all outbound packets. However, Inbound filter applies on packets that destined to Virtual Servers or DMZ host only. You can select one of the two filtering policies: 1. Allow all to pass except those match the specified rules 2.
Configuration Utility Each rule can be enabled or disabled individually. Use Rule# You can specify 8 rules for each directions: inbound or outbound. For each rule, you can define the following: • • • • • Choose the schedule when you want to make this service take effect, and select the ID you want to use with the schedule rule. Then click “Copy to” botton to copy it into the “Use rule #” box to use the schedule. When choosing rule 0 for always, it is the same as not using schedule.
Configuration Utility Schedule example Assume that there is a rule setting in Rule 1 which is Everyday 17:30~24:00, and there is a FTP server which IP is 192.168.123.5 and listening port 21. The Virtual Server’s setting is as below: Description: It means the WAN users can’t access this FTP server only at 17:30~24:00 everyday. If the time exceeds this range, the WAN users can access the LAN FTP server.
