HomePlug to Ethernet Bridge User Manual (GHPB01)
Welcome Thank you for purchasing one of the most user-friendly networking devices on the market. IOGEAR’s HomePlug to Ethernet Bridges are first-class networking devices designed to network your computers at home (or in your small office). This device allows you to set up your home network via the most pervasive medium in your house – the home power lines. It is easy to set up, and it doesn’t require any additional wiring in the house. To better serve you, IOGEAR offers an array of additional USB 2.
Table of Contents Overview 02 Technical Support 67 Features 03 Product Specifications 69 Requirements 04 Limited Warranty 70 Introduction 05 Installation 07 Network Configuration 14 Networking Basics 27 - Network Setup Wizard 27 - Checking IP Address 38 - Assign a Static IP address 40 - Sharing Disks/Folders 43 - Sharing Printers 48 - Accessing the Internet 59 Troubleshooting 63
Overview IOGEAR's HomePlug Powerline Network Ethernet Bridge allows you to network your home computers through the electric power lines in the house. Setting up a home network has never been so simple, just connect your computer to the HomePlug Bridge via the CAT5 patch cable provided in the package, and then plug the power end to your AC power outlet, you are connected! This unit is compliant to HomePlug Powerline Specification 1.0 and offers up to 14 Mbps bandwidth while being less prone to interference.
Features • No extra wires, using the most pervasive medium in your home - power lines • Allows multiple computers to share Internet access, printers, and other resources through the power lines • Very easy and intuitive to set up and install • HomePlug Powerline Specification 1.
Requirements System Requirements • • • • • Available AC power outlets in the room. Standard home power line wiring. Computers with 10/100Base-T adapters, or 10/100Base-T switch/hub. When used as a node: Windows 98SE, ME, 2000, XP. When used as a bridge: any operating system (OS transparent).
Introduction IOGEAR's HomePlug to Ethernet Bridge allows you to network your computers via your existing home power lines. It offers a data transmission speed of up to 14 Mbps, and reaches up to 990 feet through standard power lines. Package contents: 1. HomePlug to Ethernet Bridge 2. CAT5 patch cable 3. Power cable 4. User Manual 5. Warranty Registration Card 1. 2. 5 3.
Introduction Front View: (Drawing) 1. Power LED - lights up in green when plugged into a power outlet 2. Collision LED - lights up in green whenever there is collision 3. Link LED - lights up in green after plugged into a power outlet 4. ACT LED - blinks in green when there is network activity 5. Ethernet port - connecting to the computer 6. Normal/Uplink button - you only need to use this button when connecting the bridge to a switch/hub. Push this button when connects to the Uplink port on a switch.
Installation There are several ways to network your computers using the HomePlug Bridge.
Installation If you plan to use this unit as a NODE, not as a BRIDGE (refer to the Network Terms for details): 1. Remove the HomePlug Bridge, the power cord, the CAT5 cable and the installation CD from the package. 2. Allocate a space for the adapter's placement. Make sure you avoid the places mentioned on the previous page. 3. Make sure that your HomePlug bridge is NOT CONNECTED TO THE COMPUTER before you install the driver. 4. Insert the installation CD.
Installation 6. Read, understand and accept the License Agreement and Continue by clicking Next.
Installation 7. Enter a username and organization name, and continue installation. (Username and Organization have no importance in device operation. This window might look slightly different on other platforms.
Installation 8.
Installation 9. After installation is successful, a window will pop up prompting for the installation of the HomePlug Bridge. Plug in the CAT5 cable, one end into the Ethernet port on the HomePlug Bridge, the other end into an available network port on your computer. Please verify that the green Power LED and Link LED on the HomePlug Bridge light up.
Installation 10. You have reached the end of your installation. Please restart your computer for changes to go into effect.
Network Configuration HomePlug Node Configuration Steps: 1. After restarting your computer, you should see this icon on your desktop. Click on it to begin configuring your HomePlug device.
Network Configuration 2. Click Next to begin the configuration.
Network Configuration 3. Click Next to continue.
Network Configuration 4. Type in a network password between 4 and 24 characters long and click Next. The password can consist of numbers and/or letters.
Network Configuration 5. Click Next.
Network Configuration 6. Once your HomePlug Network has been configured, click Next. If other devices are present on the HomePlug network, their MAC addresses will be shown in "HomePlug Network Devices".
Network Configuration 7. After the configuration is complete, click Finish.
Network Configuration Network Terms What is a node? A node is any given device that resides or is connected onto an existing network. A computer with a network card connected to a switch is a node. The same thing applies to a Mac connected to a hub. What is a bridge? A bridge is used when connecting one side of the network with another network. Previously, connecting every computer together with the other network would mean having cables all over the place.
Network Configuration You will have to use bridges to connect two Macintoshes, because the utility software is only compatible with Windows-based computers. Can I use both in the same network? Yes. It is possible to have both nodes and bridges on a network as long as there is only a maximum of 2 bridges. It is also fine to have USB nodes on the same network with Ethernet nodes.
Network Configuration a.
Network Configuration b.
Network Configuration c.
Network Configuration d. Using the HomePlug Ethernet bridge to make a sub network HomePlug ready to communicate with the other HomePlug nodes. (Only 2 Homeplug Bridges can be used.
Networking Basics Prior to installing HomePlug, you may have had some ideas about using your new network. This section will help you get started on those ideas or even give you some new ones. It will go through the process of sharing files, printing from any computer on the network, or accessing the Internet on multiple computers with one connection. Please note that this section is just an outline of a few networking basics and not intended to be a comprehensive guide to networking.
Networking Basics Click "Next" in the window(right) for the Network Setup Wizard.
Networking Basics Read and follow the instructions in the following window and then click "Next".
Networking Basics In the following window, select among the 3 options which best describe this computer and then click "Next". If your computer connects to a broadband router/ gateway, select the second option.
Networking Basics Fill in the information in the following window as you desire and then click "Next”.
Networking Basics Enter the Workgroup name as you wish and then click "Next". (Very important: All computers on your network should have the same Workgroup.
Networking Basics Review the setting in the following screen, and click "Next" to continue. If you want to change any settings, you need to click "Back" and start over again.
Networking Basics Please wait while the Network Setup Wizard applies the changes and configures the computer.
Networking Basics When the configuration is done, the following screen will come up. Select one of the 4 options according to your needs. (In this example, the last choice was selected.) Click “Next.
Networking Basics Then click "Finish" on this next window.
Networking Basics The new setting will take effect after you restart the computer. Click "Yes" to restart the computer. Congratulations, you have completed configuring this computer! After setting up networks on all your computers on the network, you will be able to use your HomePlug network to share files, printers, and Internet connections.
Networking Basics Topic 2: Checking IP addresses in Windows XP/ 2000 Go to Start>Programs>Accessories> Command Prompt.
Networking Basics Type "ipconfig" at the prompt, then press Enter. You will see the IP address of this computer.
Networking Basics Topic 3: Assigning a Static IP Address (Note: If you use DHCP-capable gateway/router, you don't need to assign any static IP addresses because the gateway/router will automatically assign IP addresses to the computers on the network.) Go to Start>Settings>Control Panel>Network Connections>Local Area Connection Right click on Local Area Connection, then double click on Properties, you will see a window similar to this: Select “Internet Protocol (TCP/IP)” and then click on Properties.
Networking Basics At the following window, select "Use the following IP address:", and fill in the desired IP address and subnet mask (it is recommended to use the default subnet mask as shown in the following window. Subnet mask must be the same for all the computers on the network.) If you need to enter DNS address, you must enter the address of the default gateway. Click on "OK".
Networking Basics Click "Close" on the Local Area Connection Properties window. You have completed static IP address assignment.
Networking Basics Topic 4. Sharing Disks/Folders Once the network has been checked / configured, you can access other systems via "My Network Places". To allow other systems to access data on your disks / in your folders, you have to give permission to share your disks and/or folders. 1. Select the disk (or the folder) to be shared (for example in "My Computer") and right-click on the icon of the disk to get the Context / popup-menu; select "Sharing and Security.
Networking Basics Once you have selected the folder to be shared, right-click to select “sharing and security.
Networking Basics 2. In the following window, click to select "Share this folder". Then click on "Permission".
Networking Basics 3. Please note that by default, all users defined on your XP Professional system will have full permissions. You can reduce the permissions (for example to allow only Read-access) and/or you could add a different group of users to have access permission (but then you should delete the group "Everyone" from this list). In the following Permission settings, make sure you are giving the right permissions and then click OK to accept the settings.
Networking Basics 4. Click OK on the original Sharing and Security window to conclude the process. 5. Once a disk or folder is shared, the icon will show it via the "holding hand.
Networking Basics Topic 5. Share Printers You may now share any installed printers connected to this computer with other computers on your network. 1. Using the computer that has the printer already connected to it, go to: Start > Control Panel > Printers and Faxes. Click on the printer you want to share with others on the network and select "Share this printer".
Networking Basics 2. In the following window, click on "Share this Printer" and type in the share name you would like. After this is done, click on "Apply" and then "OK".
Networking Basics Now when you go to "Printers and Faxes" in the Control Panel, you will see the supporting hand underneath the printer, which means that the printer is being shared in the network.
Networking Basics For a computer to access a Network Printer, the device driver or software for that printer must be installed and pointed to the proper location of the printer. This is done similarly to the way you installed the printer on the computer it is connected to. 1. Go to a computer that is not connected to the printer and select "Start" from the Task Bar "Control Panel" then "Printers and other Hardware".
Networking Basics 2. Click on "Add a printer".
Networking Basics 3. Select the network printer option and click Next.
Networking Basics 4. Find the printer you would like to share and click Next.
Networking Basics Decide if you would like to choose this printer as a default printer and click Next.
Networking Basics You have now added the printer to your computer, click Finish. Now you may use the Network Printer as if it were directly connected to the computer. Make sure that the computer which is directly connected to the printer is on.
Sharing Internet Access Topic 6. Sharing Internet Access So how can the Internet connection be shared among other computers on the HomePlug network? Since neither the HomePlug Bridge nor USB Adapter are capable of routing at this time, a router is necessary in order to share an Internet connection. Future versions of the HomePlug Bridge or USB Adapter may feature built-in routing capabilities.
Sharing Internet Access HomePlug to USB Adapter or a HomePlug Bridge. Please note that only two (2) HomePlug Bridges are allowed on one network if used as bridges (without installation of the software).
Sharing Internet Access a. Make sure that the DSL/Cable modem is connected to the Router (using the WAN port on the router.) b. Connect the HomePlug Bridge to the Router (using the Uplink port on the router.) c. Check the link light on the HomePlug Bridge. It must light up green. IMPORTANT: The HomePlug Bridge MUST connect to the "Uplink" port on the router. d.
Sharing Internet Access Checking Router Settings: Please make sure that the following settings on your router are set: (The setup windows will depend on the router manufacturer's software.) A) The IP should be obtained automatically; B) DHCP must be enabled; C) Release DHCP and then Renew DHCP to reset the IP Addresses. It is recommended that you verify that IP Addresses are obtained. Once all the above steps have been completed, all HomePlug connected computers will be able to access the Internet.
Troubleshooting Frequently Asked Questions/Troubleshooting 1. Will HomePlug work in my house or apartment? If the house or apartment was built under U.S. building standards using copper wiring, then it will work. 2. What types of security problems will I be facing? If your house is on the same power grid as your neighbor, then there is a potential for a hacker to get in through your neighbor's house. However, this is easily remedied by activating the encryption key on the HomePlug device. 3.
Troubleshooting 4. What is the difference between bridge mode and node mode in the HomePlug Ethernet Bridge (GHPB01)? Bridge mode operates without software installation and can work with any 10/100Base-T or 10Base-T Ethernet connections. By connecting the bridge to a router, switch, or Ethernet based device (XBOX, PlayStation, Web Tablet, PocketPC, Computer, etc.), you will be able to make these devices bridge onto the HomePlug network. Currently, the GHPB01 only supports 2 bridges per HomePlug Network.
Troubleshooting conflicts with the operation of a Bridgedecor.exe file, executed on boot. To repair this problem, go into Windows Safe Mode and disable the Virtual Private Networking Adapter. You can disable the Adapter by right clicking on your Network Neighborhood Icon and clicking on properties. This will list all adapters installed on your computer. Right click and select disable on the adapter labeled Virtual Private Networking. This will allow Bridgedecor.exe to startup correctly on boot. 6.
Troubleshooting be on one network. If devices do not have the same encryption password, they will not be able to communicate with each other. 8. What OS does the HomePlug utility software fully support? Windows 98SE, ME, XP, and 2000. Windows NT and Mac are only supported by the HomePlug Ethernet Bridge (Without installing the HomePlug software with default operating mode as BRIDGE, not NODE) 9. What is the Range of HomePlug? Approximately 990 feet (300 meters) in wall power lines. 10.
Getting Technical Support To help IOGEAR® customers obtain the highest level of performance from their HomePlug devices, the IOGEAR® Service Support team is available to answer your technical questions. Do not hesitate to call if you are having trouble getting your device to work correctly.
Getting Technical Support 1) What is the purchase date and serial number of the product? 2) Were any messages displayed on the screen when the error occurred? If so, what was the exact wording of the message? 3) What type of Computer are you using? 4) When does the problem occur? 5) Can the problem be reproduced? If so, what are the steps necessary to reproduce the problem? 6) What version of the OS are you using? 7) Are you on a network? If so, what type of network is it? 8) What have you already tried to
Product Specifications 69
Limited Warranty Limited Warranty IN NO EVENT SHALL THE DIRECT VENDOR'S LIABILITY FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE PRODUCT, DISK, OR ITS DOCUMENTATION EXCEED THE PRICE PAID FOR THE PRODUCT. The direct vendor makes no warranty or representation, expressed, implied, or statutory with respect to the contents or use of this documentation, and especially disclaims its quality, performance, merchantability, or fitness for any particular purpose.
© 2002 IOGEAR® All Rights Reserved. PKG-M0024 IOGEAR and the IOGEAR logo are trademarks or registered trademarks of IOGEAR Inc. Microsoft and Windows are registered trademarks of Microsoft Corporation. IBM is a registered trademark of International Business Machines, Inc. FireWire, MAC, Macintosh, G3, G4, iMac, Apple are registered trademarks of Apple Computer, Inc. Classic is a registered trademark, licensed to Apple Computer, Inc. Finder is a trademark of Apple Computer, Inc.
Contact info. 23 Hubble • Irvine, CA 92618 • (P) 949.453.8782 • (F) 949.453.8785 • www.iogear.
