eGo Helium Portable Hard Drive ™ USB 2.
Quick Install 1. Connect the mini connector on the USB cable to the back of the drive. 2. Connect the other end of the USB cable to a USB port on your computer. The USB cable can be connected to the computer while the computer is running. Connecting the drive to a USB hub is not recommended. Mac Users: The drive should mount and appear on the Mac Desktop. PC Users: Your computer will not recognize the drive until it is reformatted. See instructions below.
Using the Drive Disconnecting the Drive CAUTION! To prevent data loss, do not disconnect the drive during data transfer (activity light flashing). Always use the safe removal procedure for your operating system when disconnecting the drive. Backing Up with Your Drive Iomega recommends periodic system backups and more frequent data backups to ensure that your critical data is always protected. The frequency of your backup should depend on the importance of your data.
Installation rapide 1. Connectez le mini-connecteur du câble USB à l’arrière du lecteur. 2. Connectez l’autre extrémité du câble USB à un port USB sur votre ordinateur. Le câble USB peut être connecté à l’ordinateur alors que celui-ci fonctionne. Il n’est pas recommandé de connecter le lecteur à un concentrateur USB. Utilisateurs de Mac : Le lecteur doit être monté et apparaître sur le bureau du Mac. Utilisateurs de PC : Vous devrez le reformater pour que l’ordinateur puisse le reconnaître.
4. Lorsque l’Assistant Création de partition s’ouvre, cliquez sur Suivant sur chaque écran pour sélectionner les options par défaut et formater le disque au format NTFS. Utilisation du lecteur Déconnexion du lecteur ATTENTION ! Pour éviter toute perte de données, ne déconnectez pas le lecteur pendant un transfert de données (voyant d’activité du lecteur clignotant). Utilisez toujours la procédure de retrait sécurisée de votre système d’exploitation lors de la déconnexion du lecteur.
Schnellstart 1. Schließen Sie den Ministecker des USB-Kabels an der Rückseite des Laufwerks an. 2. Schließen Sie das andere Ende des USB-Kabels an einen USB-Anschluss Ihres Computers an. Das USBKabel kann an den Computer angeschlossen werden, während der Computer eingeschaltet ist. Es wird nicht empfohlen, das Laufwerk an einen USB-Hub anzuschließen. Mac-Benutzer: Nun wird normalerweise das Laufwerk gemountet und auf dem Mac-Schreibtisch angezeigt. PC-Benutzer: Sie müssen das Laufwerk neu formatieren.
oder Partition erstellen (Windows 2000). 4. Sobald der Assistent zum Erstellen neuer Partitionen geöffnet wird, klicken Sie in jedem Fenster auf Weiter, um die Standardoptionen auszuwählen und das NTFS-Laufwerk zu formatieren. Das Laufwerk verwenden Trennen des Laufwerks vom System ACHTUNG! Um Datenverluste zu vermeiden, trennen Sie das Laufwerk während der Datenübertragung nicht vom Computer (Kontrolllämpchen am Laufwerk blinkt).
Installazione rapida 1. Collegare il connettore mini al cavo USB situato sul retro dell’unità. 2. Collegare l’estremità opposta del cavo USB a una porta USB sul computer. È possibile collegare il cavo USB quando il computer è acceso. Si sconsiglia di collegare l’unità a un hub USB. Utenti PC: sarà necessario riformattare l’unità. Vedere le istruzioni riportate qui di seguito. Utenti PC: il computer non riconosce l’unità finché non è formattata. Vedere le istruzioni riportate qui di seguito.
4. Quando si apre la Creazione guidata partizione, fare clic su Avanti su ogni schermata per selezionare le opzioni predefinite e formattare l’unità come NTFS. Uso dell’unità Scollegamento dell’unità ATTENZIONE! Per evitare che si verifichino perdite di dati, non scollegare l’unità durante il trasferimento di informazioni (spia di attività dell’unità lampeggiante). Quando si scollega l’unità, usare sempre la procedura di rimozione sicura specifica per il sistema operativo usato.
Instalación rápida 1. Conecte el mini conector al cable USB en la parte posterior de la unidad. 2. Conecte el otro extremo del cable USB a un puerto USB del ordenador. El cable USB se puede conectar al ordenador mientras está en funcionamiento. No se recomienda conectar la unidad a un concentrador USB. Usuarios de Mac: La unidad debe estar montada y aparecer en el Escritorio de Mac. Usuarios de PC: El ordenador no reconocerá la unidad hasta que la vuelva a formatear.
4. Cuando se abra el asistente para particiones, haga clic en Siguiente en cada pantalla para seleccionar las opciones predeterminadas y formatear la unidad NTFS. Uso de la unidad Desconexión de la unidad ¡PRECAUCIÓN! Para impedir la pérdida de datos, no desconecte la unidad durante el proceso de transferencia de datos (la luz de actividad de la unidad parpadea). Utilice siempre un procedimiento de desconexión seguro para su sistema operativo al desconectar la unidad.
Instalação rápida 1. Conecte o mini conector no cabo USB na parte posterior da unidade. 2. Conecte a outra extremidade do cabo USB à porta USB no computador. O cabo USB pode ser conectado durante o funcionamento do computador. Não é recomendável conectar a unidade a um hub USB. Usuários de Mac: A unidade deve ser montada e exibida na mesa do Mac. Usuários de PC: seu computador não irá reconhecer a unidade até que ela seja reformatada. Consulte as instruções abaixo.
Utilização da unidade Desconexão da unidade CUIDADO! A fim de evitar a perda de dados, não desconecte a unidade durante a transferência de dados (luz de atividade da unidade piscando). Sempre utilize o procedimento de remoção segura do sistema operacional ao desconectar a unidade. Execução de backup com a sua unidade A Iomega recomenda que sejam feitos backups periódicos do sistema e backups mais freqüentes de dados para garantir que seus dados mais importantes estejam sempre protegidos.
Snelle installatie 1. Sluit de miniconnector van de USB-kabel aan op de achterkant van de drive. 2. Sluit het andere uiteinde van de USB-kabel aan op een USB-poort van de computer. De USB-kabel kan op de computer worden aangesloten nadat de computer is opgestart. Wij raden u af om de drive op een USB-hub aan te sluiten. Mac-gebruikers: de drive wordt normaal geladen en verschijnt op het Mac-bureaublad. PC-gebruikers: uw computer zal de drive pas herkennen nadat deze opnieuw is geformatteerd.
4. Wanneer de Wizard Partitie verschijnt, klikt u in elk scherm op Volgende om de standaardopties te selecteren en de drive NTFS te formatteren. De drive gebruiken De drive loskoppelen WAARSCHUWING! Koppel de drive nooit los tijdens een gegevensoverdracht (wanneer het statuslampje van de driveactiviteit knippert). Gebruik voor uw besturingssysteem altijd de procedure voor veilig verwijderen wanneer u de drive loskoppelt.
Snabbinstallation 1. Anslut minikontakten till USB-kabeln på baksidan av enheten. 2. Anslut den andra ändan av USB-kabeln till en USB-port i din dator. USB-kabeln kan anslutas till datorn medan datorn är på. Vi rekommenderar inte att du ansluter enheten till en USB-hubb. Mac-användare: Hårddisken skall gå igång och kommer att visas på skrivbordet. PC-användare: Datorn kommer inte att känna av enheten om den inte formateras om. Se instruktioner nedan.
Hurtig installation 1. Tilslut ministikket på USB-kablet på drevets bagside. 2. Sæt den anden ende af USB-kablet i en USB-port på computeren. USB-kablet kan sættes i computeren, mens computeren kører. Det anbefales ikke at slutte drevet til en USB-hub. Mac-brugere: Drevet skal installeres og vises på Mac-skrivebordet. PC-brugere: Din computer genkender ikke drevet før det er blevet omformateret. Se instruktioner herunder.
Rask installering 1. Koble til minikontakten på USB-kabelen på baksiden av stasjonen. 2. Koble den andre enden av USB-kabelen til USB-porten på datamaskinen. USB-kabelen kan kobles til datamaskinen mens datamaskinen står på. Det anbefales ikke å koble stasjonen til en USB-hub. Mac-brukere: Stasjonen skal nå aktiveres og vises på Mac-skrivebordet. PC-brukere: Datamaskinen vil ikke finne stasjonen før den er formatert på nytt. Se veiledningen nedenfor.
Pika-asennus 1. Kytke USB-kaapelin miniliitin kiintolevyaseman takana olevaan liitäntään. 2. Kytke USB-kaapelin toinen pää tietokoneen USB-porttiin. USB-kaapelin voi kytkeä tietokoneeseen, vaikka tietokoneeseen on kytketty virta. Kiintolevyaseman liittämistä USB-keskittimeen ei suositella. Macintosh-käyttäjät: Aseman pitäisi asentua ja näkyä Mac-työpöydällä. PC-käyttäjät: Tietokone ei tunnista asemaa ennen kuin se on alustettu uudelleen. Katso seuraavat ohjeet.
Gyors telepítés 1. Csatlakoztassa az USB kábelen lévő mini csatlakozót a meghajtó hátoldalához. 2. Csatlakoztassa az USB kábel másik végét a számítógép USB portjához. Az USB-kábelt a számítógép bekapcsolt állapotában is csatlakoztathatja. A meghajtót nem ajánlott USB-elosztóhoz csatlakoztatni. Mac felhasználók: A meghajtót csatlakoztatni kell és megjelenik a Mac asztalán. PC felhasználók: A számítógép csak újraformázást követően ismeri fel a meghajtót. Lásd a lenti utasításokat.
Rychlá instalace 1. Připojte mini konektor kabelu USB do zadní části jednotky. 2. Druhý konec kabelu USB zapojte do konektoru USB na počítači. Kabel USB lze připojit i ke spuštěnému počítači. Nedoporučujeme připojit diskové pole k rozbočovači USB. Systém Mac: Jednotka by se měla nainstalovat a zobrazit na ploše systému Mac. Uživatelé PC: Váš počítač jednotku nerozpozná dříve, než bude znovu naformátována. Viz pokyny níže.
Skrócona instrukcja insalacji 1. Podłącz mini złącze kabla USB do tylnej części napędu. 2. Podłącz drugi koniec kabla USB do portu USB komputera. Kabel USB można podłączyć do uruchomionego komputera. Podłączanie dysku do koncentratora USB nie jest zalecane. Użytkownicy komputerów Macintosh: Dysk powinien być zainstalowany i widoczny na pulpicie komputera Macintosh. Użytkownicy komputerów PC: Twój komputer nie rozpozna napędu do momentu jego ponownego sformatowania. Patrz: poniższe instrukcje.
Γρήγορη εγκατάσταση 1. Συνδέστε το µίνι βύσµα του καλωδίου USB στο πίσω µέρος της µονάδας δίσκου. 2. Συνδέστε το άλλο άκρο του καλωδίου USB σε µια υποδοχή USB στον υπολογιστή σας. Η σύνδεση του καλωδίου USB στον υπολογιστή µπορεί να γίνει ενώ ο υπολογιστής λειτουργεί. ∆εν συνιστάται η σύνδεση της µονάδας δίσκου σε διανοµέα USB. Χρήστες Mac: Ο δίσκος πρέπει να µονταριστεί και να εµφανιστεί στο γραφείο του Mac. Χρήστες PC: Ο υπολογιστής σας δεν θα αναγνωρίσει τον δίσκο έως ότου διαµορφωθεί εκ νέου.
Limited Warranty • Garantie Limitée Eingeschränkte Garantie • Garanzia limitata Garantía limitada • Garantia limitada Iomega warrants this hardware product to be free from defects in materials and workmanship for the warranty period. This non-transferable, limited warranty is only to you, the first end-user purchaser.
Limitations THE ABOVE WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. To the extent permitted by applicable law, IOMEGA SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Any implied warranty required by applicable law shall be limited in duration to the express warranty term.
sur les politiques actuelles ou sur le service de garantie d’Iomega, veuillez visiter notre site Web www.iomega.com/ supportpolicy.html ou nous écrire à l’adresse suivante : Iomega Customer Service, 4059 South 1900 West, Roy, UT 84067. Les coordonnées des services d’assistance clientèle d’Iomega en Europe se trouvent sur notre site Web d’assistance, www. iomega.com/europe/support.
solcher Teile/Produkte Garantie geleistet, je nachdem, welcher Zeitraum länger ist. Falls die Reparatur bzw. der Ersatz eines defekten Produkts durch Iomega nicht möglich ist, ist Ihr einziges alternatives Rechtsmittel die Erstattung des ursprünglichen Kaufpreises. Die obigen Angaben stellen sämtliche Verpflichtungen dar, die Iomega Ihnen gegenüber im Rahmen dieser Garantie hat.
Iomega garantisce che questo prodotto hardware è privo di difetti di fabbricazione e dei materiali durante l’intero periodo di validità della garanzia. La presente garanzia limitata, non trasferibile, è da considerarsi valida per il solo utente finale e non può quindi essere ceduta a terze parti.
acquisto. Poiché Iomega non prevede la protezione, il ripristino o la restituzione dei dati durante l’esecuzione degli interventi di manutenzione, si consiglia sempre di duplicarli prima di procedere alla spedizione del prodotto. Limitazioni LA PRESENTE GARANZIA HA NATURA ESCLUSIVA, PERTANTO SOSTITUISCE QUALUNQUE ALTRA GARANZIA ESPLICITA O IMPLICITA.
Obtención de servicio de garantía Para recibir el servicio de garantía deberá notificar su caso al Iomega durante el período de garantía. La política y procedimientos de asistencia al cliente de Iomega (incluidas las tarifas de los servicios) cambian al ritmo que lo hacen la tecnología y las condiciones del mercado. Para obtener información acerca de las políticas actuales de Iomega o del servicio de garantía, visite nuestra página Web en www.iomega.com/supportpolicy.
a Iomega não puder reparar ou substituir um produto defeituoso, o único recurso alternativo exclusivo será a restituição da importância paga originalmente pela aquisição do produto. O exposto acima representa todas as obrigações da Iomega para com o usuário sob esta garantia.
Regulatory Information Informations relatives à la réglementation Gesetzliche Bestimmungen Informazioni sulle regolamentazioni Información reglamentaria • Regulatieve informatie Manufacturer/Responsible Party Iomega Corporation 4059 South 1900 West Roy, UT 84067 USA This equipment complies with Part 15 of the FCC Rules.
CE (European Community) This Iomega product conforms to the following European Directive(s)and Standard(s): Application of Council Directives: 73/23/ EEC, 89/336/EEC. Standards to which Conformity is declared: EN60950, EN55022, EN55024, EN61000-3-2, EN61000-3-3. Importer’s Name: Iomega International, S.A. Type of Equipment: Information Technology Equipment.
CE (Europäische Union) Dieses Iomega-Produkt hält die Bestimmungen der folgenden EU-Richtlinie(n) und Norm(en) ein: Umsetzung der Richtlinien des Rats: 73/23/EEC, 89/336/EEC. Normen, deren Einhaltung festgestellt wurde: EN60950, EN55022, EN55024, EN61000-3-2, EN61000-3-3. Name des Importeurs: Iomega International, S.A. Gerätetyp: Einrichtungen der Informationstechnik.
CE (Comunidad Europea) Este producto Iomega se ajusta a las siguientes directivas y estándares europeos: Aplicación de Directivas del Consejo: 73/23/ EEC, 89/336/EEC. Estándares con los que se declara Conformidad: EN60950, EN55022, EN55024, EN61000-3-2, EN61000-33. Nombre del importador: Iomega International, S.A. Tipo de equipo: Equipo de tecnología de la información.
Customer Support • Assistance clientèle • Kundenunterstützung Assistenza clienti • Asistencia al cliente English For service and support for your Iomega product, visit us at www.iomega.com. Français Pour obtenir du service et de l’assistance pour votre produit Iomega, visitez notre site à l’adresse suivante : www.iomega.com. Deutsch Servicedienstleistungen und Kundendienst für Ihr Iomega Produkt finden Sie unter www.iomega.com.