Ion+ Manual

ManualsBrandsiON Products ManualsSewageION X-ONEi - 1/2 HP Cast Iron Sewage Pump (2") w/ ION Digital Level Control & High Water Alarm

Ion+

Digital Level Control Switch With Alarm

OPERATION MANUAL

Dated: 08/01/2013

Document Name: Ion+_OM

Page 1 of 4

www.ionstormpro.com

Patent pending

Features

1. First of its kind, solid-state sensing technology

with no moving parts with built in high water

alarm.

2. Space age design with no mechanical contact

points.

3. Green light indicates power, orange light

indicates pump is activated, red light indicates

high water alarm.

4. Built in dry contacts for remote alarm monitoring.

5. Multipoint sealing mechanism that supersedes

single surface seals.

6. Inverter rated for use with battery backup

systems.

7. Standard piggy-back style connection for use

with manual pumps.

8. Suitable for sump and certain sewage

applications.

9. System provides integrated monitoring and

alarm.

PiPe Mounting Bracket (oPtional)

1. Determine bracket mounting position (Figure

A).

2. Mount bracket to Ion+

switch with screw

already provided in Ion+

switch (Figure B).

3. Mount Hose Clamp with switch around pipe

at predetermined level. Cable should remain

outside hose clamp (Figure C).

4. Tighten hose clamp.

Note: The Ion+

switch is available in 6" range. The

range of the switch is the distance between the On

and Off levels. The Off level is at the bracket mounting

screw of the switch.

CAUTION: Bottom of switch should not be

mounted lower than suction inlet of pump.

When installing the Ion+

switch with the pipe

mounted bracket be sure not to set the switch too low

or too high on the pipe. The Ion+

must be installed

above the inlet of the pump to prevent air-locking as

shown in the installation drawing.

To prevent ooding do not set the on point of the

switch higher than the top of the basin.

Model Cord Range

INP20306 10 ft 6 in

INP20376 20 ft 6 in

Piggy-Back installation

Electrical outlet must not be located in pump pit.

Electrical outlet voltage, piggy-back plug voltage and

pump voltage must all be the same voltage.

DO NOT CUT plug off unit.

Ensure vent tube on plug is protected from moisture,

dirt and insects and other items that could plug or

block tube.

1. Insert the Ion+

switch’s piggy-back plug into

the outlet.

2. Plug pump into piggy-back plug (Figure E).

3. Allow system to cycle to ensure proper

installation.

Please note this product may not work in

conjunction with other controllers.

Note: The Ion+

switch does not operate like a

standard pressure switch. There are no contacts to

wear out, so when pressure is applied, there will not

Summary of content (4 pages)

PAGE 1
Ion+® OPERATION MANUAL Dated: 08/01/2013 Document Name: Ion+_OM Digital Level Control Switch With Alarm Patent pending Page 1 of 4 3. Mount Hose Clamp with switch around pipe at predetermined level. Cable should remain outside hose clamp (Figure C). 4. Tighten hose clamp. Note: The Ion+® switch is available in 6" range. The range of the switch is the distance between the On and Off levels. The Off level is at the bracket mounting screw of the switch. Features 1.
PAGE 2
Ion+® OPERATION MANUAL Dated: 08/01/2013 Document Name: Ion+_OM Digital Level Control Switch With Alarm be a click. FIGURE B Page 2 of 4 FIGURE C Safety Precautions CAUTION: To prevent electric shock, ensure product is connected to a grounded outlet. The electrical outlet should be properly wired to a dedicated 15A circuit breaker. Proper short-circuit and overload protection must be provided at the distribution panel. Install in accordance with all local and national electrical codes.
PAGE 3
Ion+® Digital Level Control Switch With Alarm Troubleshooting Switch Does Not Turn On Pump 1. Test the pump without the Ion+® switch OPERATION MANUAL Dated: 08/01/2013 Document Name: Ion+_OM Page 3 of 4 range Ion+® switch. c. For a pump-mounted switch, see Page 2, Figure D to verify that the On level is appropriate for your basin. a. Plug the pump directly into the wall outlet, without plugging it into the switch plug. i. If the On level is too high, the switch will have to be replaced. b.
PAGE 4
Ion+® Digital Level Control Switch With Alarm OPERATION MANUAL Dated: 08/01/2013 Document Name: Ion+_OM Page 4 of 4 3 Year Residential Warranty 1. Coverage and Term. Metropolitan Industries, Inc. (“Metropolitan”) warrants to the original purchaser (the “Buyer”) of each Ion|StormPro product (the “product”), that any part thereof which proves to be defective in material or workmanship within three (3) years from date of manufacture, will be replaced at no charge with a new or remanufactured part, F.O.B.