Telesounds Quickstart Guide English ( 2 – 7 ) Guía de inicio rápido Español ( 8 – 13 ) Appendix English ( 14 – 15 )
Quickstart Guide (English) Introduction Thank you for purchasing the Telesounds. At ION, your entertainment is as important to us as it is to you. That’s why we design our products with one thing in mind—to make your life more fun and more convenient. Important Safety Notices Warning: Prolonged exposure to excessive sound pressure (high volumes) from headphones can cause permanent hearing loss. Warning: Do not expose batteries to excessive heat such as sunlight, fire, or the like.
Features Transmitter Front Panel 1. Charging Dock: Place the headband of the headphones on this dock (on top of the transmitter) to charge them. Make sure that the transmitter is connected to a power outlet and that its Power switch is set to On. 2. Charge Light: This light is green when the headphones (placed on the charging station) are charging. It will turn off when the headphones are fully charged. 3. Power Light: This light is blue when the transmitter is powered on.
Headphones 3 2 1 4 1. Power Button: Press and hold this button for about 2 seconds to power the headphones on or off. If the headphones detect no audio signal for about 5 minutes, they will power off automatically to save battery power. 2. Status Light: This light indicates the status of the headphones: • Red: The headphones are powered on but not connected wirelessly to the transmitter. • Flashing red: The headphones are low on battery power.
Setup Items not listed under Introduction > Box Contents are sold separately. Powering the Headphones The headphones are powered by 2 rechargeable AAA batteries, which must be charged by the transmitter. Use the included batteries only. With fully charged batteries, you can use the headphones for approximately 10 hours. It takes approximately 6 hours to fully charge them. If this is the first time you are using them, charge them for the full 6 hours.
Setting up the Transmitter & Headphones General Notes: • If this is the first time you are using the headphones, charge them for full 6 hours before use. See Powering the Headphones above. • If your sound source has built-in speakers or if you are using external speakers with it, you can use Telesounds in addition to those speakers.
To set up the headphones with the transmitter: 1. After setting up the transmitter (see above), set the Power switch on the transmitter to On. 2. After installing the included batteries in the headphones and charging them (see Powering the Headphones), press and hold the power button on the headphones for about 2 seconds. The light next to the button will turn red. 3. Wait a few seconds for the headphones and transmitter to connect wirelessly to the transmitter.
Guía de inicio rápido (Español) Introducción Gracias por comprar el Telesounds. En ION, su entretenimiento es tan importante para nosotros como para usted. Por eso es que diseñamos nuestros productos con una sola cosa en mente—hacer que su vida sea más divertida y cómoda. Avisos importantes sobre la seguridad Advertencia: La exposición prolongada a presión sonora excesiva (altos volúmenes) de los auriculares puede causar pérdidas de audición permanentes.
Características Transmisor Panel frontal 1. Estación de carga: Coloque la vincha de los auriculares en esta estación de carga (en la parte superior del transmisor) para cargarlos. Asegúrese de que el transmisor esté conectado a un tomacorriente y que su interruptor de encendido esté en On (encendido). 2. Luz Charge: Se enciende de verde cuando los auriculares (ubicados en estación de carga) se están cargando. Se apagará cuando los auriculares estén completamente cargados. 3.
Auriculares 3 2 1 4 1. Botón de encendido: Mantenga pulsado este botón durante 2 segundos para encender o apagar los auriculares. Si los auriculares no detectan ninguna señal de audio durante aproximadamente 5 minutos, se apagarán automáticamente para ahorrar pilas. 2. Luz de estado: Este luz indica el estado de los auriculares: • Rojo: Los auriculares están encendidos pero no están conectados de forma inalámbrica con el transmisor. • Rojo destellante: Las pilas de los auriculares se están agotando.
Instalación Los elementos que no se enumeran en Introducción > Contenido de la caja se venden por separado. Encendido de los auriculares Los auriculares son alimentados por 2 pilas AAA recargables, las cuales deben ser cargadas por el transmisor. Use solamente las pilas incluidas. Con las pilas completamente cargadas, puede usar los auriculares durante aproximadamente 10 horas. Una carga completa demora aproximadamente 6 horas. Si es la primera vez que las utiliza, cárguelas completamente durante 6 horas.
Instalación del transmisor y los auriculares Notas generales: • Si es la primera vez que utiliza los auriculares, cárguelos completamente durante 6 horas antes de usarlos. Consulte Encendido de los auriculares más arriba. • Si su fuente de sonido cuenta con altavoces integrados o si está utilizando altavoces externos con ella, puede utilizar el Telesounds además de dichos altavoces.
Como configurar los auriculares con el transmisor: 1. Luego de configurar el transmisor (ver más arriba), ajuste el interruptor Power el transmisor en On. 2. Luego de instalar las pilas incluidas en los auriculares y cargarlas (consulte Encendido de los auriculares), mantenga pulsado el botón de encendido de los auriculares durante aproximadamente 2 segundos. La luz junto al botón se encenderá de rojo. 3. Espere unos segundos hasta que los auriculares y el transmisor se conecten inalámbricamente.
Appendix (English) Technical Specifications Specifications are subject to change without notice. Wireless reception and range are affected by walls, obstructions, and movement. For optimal performance, place the product in the center of the room so it is unobstructed by walls, furniture, etc. Battery life may vary based on temperature, age, and volume usage of product. * We recommend using the included rechargeable batteries.
Receiver (Headphones) Frequency Response 20 Hz – 20 KHz (+3 dB) SNR > 85 dB THD < 0.3% Distortion < 0.5% Channel Separation > 75 dB Driver 1.6” / 40 mm Sound Pressure Level 105 dB Output Impedance 24 Ω (±3.6) Output Power 7 mW Reception Frequency 2.4 GHz Digital UHF Type Frequency-hopping system (Gaussian frequency-shift keying [GFSK]) Range 98 ft. / 30 m Connections Power (1) 1/8” (3.5 mm) audio input Type 2 rechargeable NiMH 1.
ionaudio.com Manual Version 1.