User Manual

ManualsBrandsIP Mobilenet ManualsElectronicsIP8HPV Data Transceiver

~\Technical Documentation\Install_Guides\MR-Guide\3-Jan-02 Page 1 of 14

INSTALLATION GUIDE

INVADR

MOBILE RADIO SYSTEM

INSTALLATION GUIDE CONTENTS:

Section Title Page



INVADR

Mobile Radio Illustration .....................................



Installation Overview and Safety Reminder.........................



Installation Requirements ....................................................



Pre-Installation Guidelines ...................................................



Mounting the INVADR

Mobile Radio.................................



Serial Cable Connection and Routing..................................



EMI Filter Installation ...........................................................



Power Supply Installations...................................................



Switch Installation ................................................................



Delay Timer Installation .......................................................



Antenna Installation .............................................................



VIU (Vehicle Interface Unit) Connections ............................



Testing and Installation Checklist ........................................



Vehicle Unit Wiring Interconnection Layout .......................



Diversity Antenna Vehicle Installation Detail Diagram.......



Mobile Antenna Distance Matrix ........................................



Vehicle Unit Wiring Interconnection Layout with VIU

(Voice Interface Unit)..........................................................



Vehicle Unit Wiring Interconnection Layout with

Data911 and VIU (Voice Interface Unit).............................

IPMN p/n: 516-80307

Document Control #: DC-10

Version: C-1

11909 East Telegraph Road, Santa Fe Springs, CA 90670-3785

Voice: (562) 946-9493 Fax: (562) 949-0223

Notice:

While reasonable efforts were made to ensure that the information in this document was complete and accurate at the time

of printing, IPMobileNet, Inc. can assume no responsibility for any inaccuracies. Changes and corrections to the

inforrmation within this document may be incorporated into future releases.

Summary of content (14 pages)

PAGE 1
INSTALLATION GUIDE INVADRtm MOBILE RADIO SYSTEM INSTALLATION GUIDE CONTENTS: Section Title Page tm INVADR Mobile Radio Illustration ..................................... 2 Installation Overview and Safety Reminder......................... 2 Installation Requirements .................................................... 3 Pre-Installation Guidelines ................................................... 5 Mounting the INVADRtm Mobile Radio.................................
PAGE 2
INVADRtm Mobile Radio Illustration TX/RX1 RX2 Mounting Bracket Power Cable TX FCC ID Red M17-EC8DT450TX xxxxxxxxxxx xxxxwweddd xxxxxxxx xxxxwweddd Black Serial Cable DB9 Installation Overview This guide will provide standard steps involved in the installation process of an INVADRtm Mobile Radio. This guide includes wire routing and connections between the radio, other components, and the vehicle’s power. Safety Reminder 1.
PAGE 3
INSTALLATION REQUIREMENTS PL502-82019-51 - INVADR MOBILE ACCESSORY KIT -- An INVADR Mobile Radio includes the following components (part of mobile top assembly): Qty Description IPMN Part Number 1 Cable, Power Extension 502-82020-53 2 ‘L’ Brackets 2 Screws Skt Cap Button Head 10-32 X 5/8 37081032-10 6 Washers Split Lock #10 271-0062-010 2 Washers Fender 1” O.D. X .28 I.D. X .05 THK 271-0059-001 4 Washers Rubber 1” O.D. X .65 I.D. X .12 THK 36040001 2 Hoses, Rubber Black .380 O.D. X .
PAGE 4
OPTIONAL INSTALLATION SUPPLIES – Order each item individually: Qty Description IPMN Part Number 1 Serial Cable (DB9MF), 20 ft. 156-0245-020 1 Wire, 8 (133/29) AWG VW-1 Red, by foot, order 19.5 ft. 156-0243-003 1 Wire, 8 (133/29) AWG VW-1 Black, by foot, order 19.5 ft. 156-0243-001 2 RG58U Cable and Mount, VHF, 17 ft. (incl ¾” Brass Mount and N Male Crimp) 102-0200-001 2 RG8X Cable and Mount, UHF & 800 MHz, 17 ft.
PAGE 5
INSTALLATION INSTRUCTIONS Pre-Installation Guidelines 1. 2. Prior to installing new equipment, remove existing equipment and all related components to include stock clips on radio wiring harness and antenna. Mounting the INVADRtm Mobile Radio To mount the radio, perform the following steps: Step 1 Mounting of the radio, delay timer, relay, and filter will take place in the trunk compartment (see Fig. 1) unless installing in a vehicle without a trunk. Secure the radio into the trunk compartment.
PAGE 6
EMI Filter Installation MDC Power Supply Installation (IPMN p/n: 127-0020-001) NOTE: The EMI Filter protects the radio and filters out noise. To install the MDC power connection, perform the following steps: To install the filter, perform the following steps: Step 1 Connect the MDC power cable to the MDC. Step 1 Secure the EMI Filter in the trunk compartment of the vehicle (see Fig. 5) near radio mounting location.
PAGE 7
Carling Switch Installation Delay Timer Installation (DPST Heavy Duty Toggle) (IPMN p/n: 150-0127-001) (IPMN p/n: 144-0136-001) To install the Delay Timer, perform the following steps: To install the switch, perform the following steps: Step 1 Mount the switch in the selected location. Step 2 Route and wire a red wire (#12 AWG) from of the switch to the Automotive Power Relay (see Fig. 9). Step 3 Ground the switch by routing and wiring a black wire from the switch to the vehicle chassis.
PAGE 8
Antenna Installation VIU Connections If connecting a VIU, an additional serial cable is required. NOTE: Two (2) antennas are mounted and installed on the roof of the vehicle using specific measurements for distance. 10-ft serial cable (IPMN p/n: 156-0245-010) included with VIU To connect the serial cables, perform the following steps: To mount and install the antennas, perform the following steps: Step 1 Install antennas (see sample drawing DT450-10-0201 and Fig. 11 below).
PAGE 9
INVADR Mobile Radio Testing 1. tm To verify that the INVADR Mobile Radio setup works properly, use a wattmeter and a service monitor. NOTE: If a wattmeter and a service monitor are not available, begin test from Step 3 through 6 and 10 through 12. 2. Connect the wattmeter between the radio and the coax connector. 3. Connect the radio to a computer with the IPMobileNet IP Message Utility program loaded.
PAGE 10
VEHICLE UNIT WIRING INTERCONNECTION LAYOUT 400−512ΜΗζ ∗∆Ις ΕΡΣΙΤΨ ΜΟΒΙΛΕ ∆ΑΤΑ ΡΑ∆ΙΟ ~\Technical Documentation\Install_Guides\MR-Guide\3-Jan-02 Page 10 of 14
PAGE 11
MOBILE ANTENNA DISTANCE MATRIX Frequency Band in MHz Center Frequency in MHz Antenna Spacing** @ ¼ Wavelength Antenna Spacing** @ ¾ Wavelength NFEZ* in inches for Radome Antenna NFEZ* in inches for ¼ Wavelength Whip NFEZ* in inches for “⅝” Wavelength Whip Wavelength in Inches 130-140 135.000 21.87 N/A 0.25 10.94 N/A 87.49 140-150 145.000 20.36 N/A 0.27 10.18 N/A 81.46 150-160 155.000 19.05 N/A 0.29 9.53 N/A 76.20 160-174 162.000 18.23 N/A 0.30 9.11 N/A 72.
PAGE 12
DIVERSITY ANTENNA MOBILE INSTALLATION DETAIL (Typical installation) ~\Technical Documentation\Install_Guides\MR-Guide\3-Jan-02 Page 12 of 14
PAGE 13
VEHICLE UNIT WIRING INTERCONNECTION LAYOUT (with Voice Interface Unit – VIU) 4 00−512ΜΗζ ∗∆Ις ΕΡΣΙΤΨ ΜΟΒΙΛΕ ∆ΑΤΑ ΡΑ∆ΙΟ ~\Technical Documentation\Install_Guides\MR-Guide\3-Jan-02 Page 13 of 14
PAGE 14
VEHICLE UNIT WIRING INTERCONNECTION LAYOUT (Data 911 with Voice Interface Unit – VIU) 400−512ΜΗζ ∗∆Ις ΕΡΣΙΤΨ ΜΟΒΙΛΕ ∆ΑΤΑ ΡΑ∆ΙΟ ~\Technical Documentation\Install_Guides\MR-Guide\3-Jan-02 Page 14 of 14