Specification Sheet

ManualsBrandsipolex ManualsComputers & AccessoriesColored 10G SFP+ Twinax Cable, Direct Attach Copper(DAC) Passive Cable in Blue, 0.5m (1.64ft), for Cisco SFP-H10GB-CU0.5M, Meraki, Ubiquiti, Mikrotik, Intel, Fortinet, Netgear, D-Link, Supermicro

ShenZhen Ipolex Co., Ltd

Driving Your Next Generation Networks www.ipolex.com

E-mail: 2997130431@qq.com Tel: +8615814427629

10G SFP+ Passive Copper Cable Assembly

CAB-10GSFP-PxM

Features

 SFF-8431 Compliant

 Broadband serial data rate operation:10 Mbps to 12 Gbps

 Power Level I: 15 mW per cable end

 100 Ohm differential impedance

 Retractable pin latch

 EEPROM signature

 Pull to Release latch design

 360°cable braid crimp

 Enhanced EMI skirt design

 Color options for strain relief and pull tab

 Linear design for use with EDCs

 AC-coupled inputs and outputs

 30AWG to 24AWG cable available

Applications

 10 Gigabit Ethernet and Gigabit

 Ethernet (IEEE 802.3ae)

 Fiber Channel: 1, 2, 4, 8, and 10GFC

 Infiniband SDR, DDR, and QDR

 Fiber Channel over Ethernet (FCoE)

 Serial data transmission

Product Description

The passive SFP+ Direct attach copper cable assembly is a low cost alternative for short

reach applications. The design allows for a serial data transmission up to 12Gbps in each

direction. The passive design has no signal amplification in the cable assembly. Electronic

Dispersion Compensation (EDC) is typically used on host board designs when passive copper

Summary of content (11 pages)

PAGE 1
ShenZhen Ipolex Co., Ltd www.ipolex.
PAGE 2
ShenZhen Ipolex Co., Ltd www.ipolex.com Driving Your Next Generation Networks cable assemblies are utilized. EDC allows for an extended length of passive cable assemblies. EEPROM signature enables the host to differentiate between a passive copper cable assembly and a fiber optic module. The mechanical design of the braid crimp and EMI skirt ensure that EMI radiation is sufficiently suppressed. Additionally, the copper cable acts as a natural heat sink.
PAGE 3
ShenZhen Ipolex Co., Ltd www.ipolex.com Driving Your Next Generation Networks Frequency Domain Item 1 2 3 4 Test Parameter Receive Return Loss (SDD22) Transmit Return Loss (SDD11) Common Mode Reflection (SCC22) Common Mode Conversion (SCD11) Specification (Proposal ) -12+2*SQRT(f) @ 0.01 to 4.1GHz < -6.3 + 13 * log10(f/5.5), with f in GHz ; @4.1 to 11.1GHz -12+2*SQRT(f) @ 0.01 to 4.1GHz < -6.3 + 13 * log10(f/5.5), with f in GHz ; @4.1 to 11.1GHz < -7 + 1.6 × f, with f in GHz；@ 0.01 to 2.5GHz -3dB @ 2.
PAGE 4
ShenZhen Ipolex Co., Ltd www.ipolex.com Driving Your Next Generation Networks Host board Connector Pinout Figure 1: MSA compliant Connector Figure 2: Pin Definitions.
PAGE 5
ShenZhen Ipolex Co., Ltd www.ipolex.com Driving Your Next Generation Networks Note 2. This pin is an open collector/drain output pin and shall be pulled up with 4.7-10k to Vcc_Host on the host board. Pull ups can be connected to multiple power supplies, however the host board design shall ensure that no module pin has voltage exceeding module VccT/R + 0.5 V. Note 3. This pin is an open collector/drain input pin and shall be pulled up with 4.7-10k to VccT in the module. Note 4.
PAGE 6
ShenZhen Ipolex Co., Ltd www.ipolex.com Driving Your Next Generation Networks capacity of 500 mA. Signal: The two high speed signal pairs, TD+/TD- and RD+/RD-, are 100 Ohm differential impedance transmission lines with AC coupling on each RD trace. 2 Wire Interface EEPROM The EEPROM on the SFP+ passive cable assembly is designed for 256 addresses. The information for addresses 0 to 127 is listed below. This information can be tailored to any customer request.
PAGE 7
ShenZhen Ipolex Co., Ltd www.ipolex.
PAGE 8
ShenZhen Ipolex Co., Ltd www.ipolex.
PAGE 9
ShenZhen Ipolex Co., Ltd www.ipolex.com Driving Your Next Generation Networks 117 118 119 120 121 122 123 124 125 126 127 75 76 77 78 79 7A 7B 7C 7D 7E 7F 0 0 0 0 0 0 0 0 0 0 0 Mechanical Specifications Mechanical Parameter Minimum Cable Diameter (24 AWG) Bend Radius (24 AWG) Inches 0.185 Inches 0.8 Inches 0.175 Inches 0.7 Inches Within Pair Skew 120 Cable Insertion Loss Unit Inches 1.25 Cable Diameter (30 AWG) Bend Radius (30 AWG) Maximum 0.
PAGE 10
ShenZhen Ipolex Co., Ltd www.ipolex.com Driving Your Next Generation Networks Mechanical Dimensions Ordering information 10G SFP+ Copper Cable Assemblies, Passive P/N Length Data Rate AWG Length Tolerance CAB-10GSFP-P50CM 0.5 M 10G 24 28 30 +0.1/-0.0m CAB-10GSFP-P1M 1M 10G 24 28 30 +0.1/-0.0m CAB-10GSFP-P2M 2M 10G 24 28 30 +0.3/-0.3m CAB-10GSFP-P3M 3M 10G 24 28 30 +0.3/-0.3m CAB-10GSFP-P5M 5M 10G 24 28 / +0.6/-0.6m CAB-10GSFP-P7M 7M 10G 24 / / +0.9/-0.
PAGE 11
ShenZhen Ipolex Co., Ltd www.ipolex.com Driving Your Next Generation Networks Revision History Revision Initiated Review Approved Revision History Release Date V1.3 Vinson Steven Nicky Released. Jul/2016 V1.4 Vinson Steven Nicky Released. Aug/2017 V1.5 HT.HUANG Steven Nicky Released. Nov/2017 Further Information For further information, please contact info@ipolex.com E-mail: 2997130431@qq.com Tel: +8615814427629 Web: www.ipolex.com 11 E-mail: 2997130431@qq.