Instructions / Assembly

ManualsBrandsIQ America ManualsElectricalWireless Plug-In Door Chime

This package contains:

• Traditional Plug-In Doorbell

Installation Instructions

Please note: Positioning the pushbutton or door chime on or near metal

structures or reinforced PVC doors or doorframes will reduce the transmission

range.

Install the Door Chime

Plug the Plug-in Chime into any electrical outlet within the house. The

chime must be within transmission range of the Doorbell pushbutton.

The Plug-in Chime will play all of the tunes that are available when it

is ﬁrst powered up.

Program the Doorbell Pushbutton Transmitters

Press the Front Doorbell pushbutton and the chime will respond

with a tune. This indicates that the pushbutton has been programmed

to the chime. Program the Back Doorbell pushbutton by pressing the

Back Doorbell pushbutton and the chime will respond with a tune.

NOTE: Programming of the Back Doorbell pushbutton must be

completed within 2 minutes of programming the Front Doorbell

pushbutton or the plug-in chime will not accept it. If this happens

you will need to Reset the chime programming. Please reference “To Reset

the Chime Programming” section if needed.

Sound Selection (Refer to Figure 1)

Front Doorbell Pushbutton—Press Button A until you hear the desired

chime. You can change the chime at any time by pressing this button.

Back Doorbell Pushbutton—Press Button B until you hear the

desired chime.

Chime Options Table

1. 8 Note Westminster (Front Default)

2. 2 Note Chime (Back Default)

3. 1 Note Chime

The volume adjustment knob C (Figure

1) enables you to adjust the volume of

your door chime at any time.

Speciﬁcation

Range ..............................................................................................up to 150 ft.

Electrical Load ..... 1 x CR2032 Lithium Battery for Doorbell Pushbutton

Note

This device complies with part 15 of FCC Rules. Operation is subject to the following

two conditions:

(1) This device may not cause harmful interference, and

(2) This device must acce pt any interference received, including interference that

may cause undesired operation.

The changes or modiﬁcations not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment. To comply with

FCC RF exposure requirements, this device and its antenna must not be co-located or

operated in conjunction with any other antenna or transmitter.

To Reset the Chime Programming

While plugged in to an electrical outlet, press and hold button A and

B until the plug-in chime sounds. The chime will play all of the tunes

available indicating that previous programs have been erased. Return

to the Programming Doorbell Pushbutton Transmitters and repeat section.

Troubleshooting

Chime doesn’t sound when pushbutton is pressed

Check that the battery has been inserted correctly. The doorbell pushbutton LED light

should come on when the pushbutton is pressed.

Doorbell pushbutton may be positioned out of range of the door chime.

Move the door chime closer to the pushbutton.

Note: During the programming cycle, the transmission range may be reduced and will

resume optimum range after 2 minutes.

A metallic object may be blocking the signal to the door chime from the pushbutton

position. Experiment with the location of the door chime to see if you can move it to a

more suitable place.

Battery in the pushbutton may need replacing.

When pushed, the pushbutton LED will ﬂash 5 times when the battery needs replacing.

See instruction for Installing the Battery.

Note: In cold conditions, poor location or environment, operating at maximum range it

is advisable to replace the battery more frequently (i.e. every 12-18 months) to maintain

optimum performance.

Your pushbutton and chime haven’t been programmed. Reset the automatic

programming of your chime and doorbell pushbutton by Pressing and holding down

chime selection buttons A and B (Figure 1) for 5 seconds. The chime will sound all of

the tunes available indicating the programming has been erased. Program the doorbell

pushbutton following the installation instructions.

For any other problem, call 1-800-296-1869 Mon-Fri between 9 a.m. and 5 p.m. EST.

Plug-In Chime

Figure 1

DETAIL X

SCALE 2.000







DETAIL X

SCALE 2.000

IQ America Two Year Warranty

This is a “Limited Warranty” which gives you speciﬁc legal rights. You may also

have other rights which vary from state to state and province to province.

For a period of two years from the date of purchase, any malfunction caused by

factory defective parts or workmanship will be corrected at no charge to you. To obtain a

refund or replacement, return the product to the place of purchase.

NOT COVERED: Repair service, adjustment and calibration due to misuse, abuse

or negligence. Unauthorized service or modiﬁcation of the product or of any furnished

component will void this warranty. This warranty does not include reimbursement for

inconvenience, installation, setup time, loss of use or unauthorized service.

This warranty covers only IQ America products and is not extended to other

equipment and components that a customer uses in conjunction with our products.

This warranty is expressly in lieu of all other warranties, express or implied,

including any warranty, representation or condition of merchant ability or that the

products are ﬁt for any particular purpose or use, and speciﬁcally in lieu of all special,

indirect or incidental or consequential damages.

Repair or replacement shall be the sole remedy of the customer and there

shall be no liability on the part of IQ America for any special, indirect, incidental or

consequential damages, including but not limited to any loss of business or proﬁt,

whether or not foreseeable. Some states or provinces do not allow the exclusion or

limitation of incidental or consequential damages, so the above limitation or exclusion

may not apply to you. Retain receipt for warranty claims.

Operating Voltage ....................................................................120VAC, 60Hz

Standby and Operating Current ............................................................. 0.1A

Model WD-2044A - ACGPI

(WD-2044)

WD-2044-ACGPI: MANL-WD2044-ACGPI.ed4)

I-MANL-IQAPLPWD2044

IQ: IM-WD-2044A(25-11-09)-1

Summary of content (2 pages)

PAGE 1
Plug-In Chime Model WD-2044A - ACGPI (WD-2044) DETAIL SCALE This package contains: To Reset the Chime Programming • Traditional Plug-In Doorbell Installation Instructions Please note: Positioning the pushbutton or door chime on or near metal structures or reinforced PVC doors or doorframes will reduce the transmission range. While plugged in to an electrical outlet, press and hold button A and B until the plug-in chime sounds.
PAGE 2
Campanilla de Corriente Eléctrica Modelo WD-2044A (WD-2044) DETAIL SCALE Este Paquete Contiene: Para Reprogramar la Campanilla • Campanilla Tradicional de Corriente Eléctrica Instrucciones Para Instalar Favor de Notar: Instalar el botón o campanilla en o cerca de superﬁcies metálicos o puertas o marcos de PVC reforzados puede reducir el alcance de la transmisión. Apretar y aguantar el Botón A y B hasta que suene la campanilla.