Installation Manual

3
Safety Information
WARNINGS
• Use of equipment, components and accessories other than those specified by IQAir may impair safety provided
by the equipment. Safety of any system incorporating the equipment is the responsibility of the installer of the
system.
• PoE power injector or USB adapter are not to be positioned so that it is difficult to unplug them.
• When using in covered outdoor areas, the PoE power injector or USB adapter is to be installed in a weatherproof
enclosure or indoor with the cable routed through a wall or window feedthrough.
CAUTION
• The IQAir AirVisual Outdoor enclosure is designed to be water resistant to rain or spray. It is not designed to be
waterproof when immersed. Setting it in a pool of water will result in flooding the inner compartment with water.
This will severely damage your IQAir AirVisual Outdoor. DO NOT install the IQAir AirVisual Outdoor less than 1
meters or 3 feet from the ground. Setting the bottom of IQAir AirVisual Outdoor too close to a surface will result
in water splashing back into the inlet and may result in damage to the device.
• DO NOT mount the IQAir AirVisual Outdoor upside down. To increase sampling efficiency, the PM sensor is
covered by a porous screen but is not splash- or waterproof. The IQAir AirVisual Outdoor has ingress protection
from top and front side for splash water. Direct injection of water into the device is likely to damage it.
• PoE power injector or USB adapter are not intended for outdoor use.
1. Before plugging PoE power injector or USB adapter into a socket check if voltage and frequency corresponds
to 100 to 240 V and to 50 to 60 Hz.
2. Do not use the equipment at altitudes exceeding 2 000 meters (6 560 feet).
3. The power to run the IQAir AirVisual Outdoor is 12 W (48.0 VDC and 0.25 A PoE or 5.2 VDC and 2.4 A USB).
It is recommended to power the IQAir AirVisual Outdoor through the RJ45 Ethernet connector with the supplied
PoE Injector and cables. There are no outputs available from the IQAir AirVisual Outdoor.
4. The supplied power supply is rated to operate between 0°C to 45°C (32°F to 113°F) with humidity ranging
from 0% to 95% noncondensing but the IQAir AirVisual Outdoor is rated to operate between –20°C to 50°C (-4°
F to 122°F). IQAir recommends running the IQAir AirVisual Outdoor within these temperature limits.
5. The IQAir AirVisual Outdoor is designed to be used outdoors in highly polluted areas where particulate
concentrations can be as high 1000 µg/m3.
LASER SAFETY
• IQAir AirVisual Outdoor sensor modules are Class 1 laser-based instruments.
• During normal operation, you will not be exposed to laser radiation.
• DO NOT open the IQAir AirVisual Outdoor when it is powered ON.
• You will not be exposed to the laser radiation when the IQAir AirVisual Outdoor is disassembled.
• The PM sensor has a laser inside it. DO NOT open the PM sensor inside IQAir AirVisual Outdoor when it is
powered ON
Precautions:
DO NOT remove any parts from the IQAir AirVisual Outdoor
WARNING
The use of controls, adjustments, or procedures other than those specified in this manual may result in
exposure to hazardous optical radiation.
WARNING
If the IQAir AirVisual Outdoor is used in a manner not specified by the manufacturer, the protection
provided by the equipment may be impaired.
When operated according to the manufacturer’s instruction, this device is a Class 1 laser product as defined by U.S.
Department of Health and Human Services standards under the Radiation Control for Health and Safety Act of
1968.
This equipment is to be operated with provided accessories only. Equipment and accessories are to be supplied by
IQAir or its agent only. In case of operation with USB adapter, use model ICP20-052-2400B from manufacturer
Shenzhen Shi Ying Yuan Electronics Co., Ltd., Fl 5-7 Of West, Bldg 8, Hongye Industry Park, Lezhujiao
Resident Squad, Huangmabu Comminity, Xixiang St., Bao'an District, 518126 Shenzhen, GuangDong Province,
China only and keep ambient temperature of USB adapter at max. 25°C. This equipment is to be cleaned with a
damp cleaning cloth wetted with warm water containing some drops of dishwashing detergent. After cleaning,
dry it with a cloth.
This equipment is intended for use at supply voltages with fluctuations not exceeding +/-10 % and classified as
overvoltage category II. This equipment is intended for use in environment classified as pollution degree 2 and it is
not to be stored or used in wet locations.