IRISPen Air 7 Quick User Guide (Android)
This Quick User Guide helps you get started with the IRISPen Air 7. Please read this guide before operating this scanner and its software. All information is subject to change without prior notice. TM Table of Contents 1. Introduction 2. Installation of the IRISPen app TM 3. Quick Setup of the IRISPen TM 4. Scanning 5. Troubleshooting 6. Specifications 7. Compliance 1.
2. Installation of the IRISPenTM app Important: to install the IRISPen app you need a wireless Internet connection. TM Open the Play Store on your Android device. Search for the IRISPen Air 7 app and install it. To do so follow the on-screen instructions. Once the app has been installed, tap Open. Press the scanning tip for 3 seconds to power on the pen, as shown in the IRISPen app. TM TM The blue Bluetooth led on the pen starts to blink slowly. Tap Start.
3. Quick Setup of the IRISPenTM When you start the app for the first time the Quick Setup is displayed. In the Quick Setup you can select: The Scanning hand: Select Right hand to scan lines from left to right. Select Left hand to scan lines from right to left. The Input language IRISPen supports 130* languages. TM *130 languages will be supported in the final version of IRISPen AirTM 7, which clients will be able to download through the Update feature in the current application.
Scanning Tips Then continue to Scanning tips. Hold the pen upright to scan text. Do not scan in a 45 degree angle or less. Make sure both sharp ends of the scanner tip always touch the page during scanning. Scan one line of text at a time. Make sure the line is approximately in the middle of the two scanner tips. Avoid scanning too slowly. Slide the IRISPen smoothly, in a fluid motion. Avoid applying excessive pressure. Otherwise, the scanning may result in jerky, uneven motions.
4. Scanning In this section we explain the different scanning possibilities of the IRISPen . TM Tap the plus sign to start a new document. A new document is always named "untitled document". To rename it, tap inside the title and enter a name of your choice. "Ready to scan" now appears on the screen. Slide the pen over a line of text as explained in the Quick Setup. The scanned text appears in the application. You can add multiple lines to a document until the document if full.
Translating text Note: make sure Online mode is activated to use this feature. An Internet connection (Wifi, 3G or 4G) is required to activate Online mode. To translate the text you have scanned, tap the Translate icon ( ). Tap the language on the right-hand side and select the required language from the list. The text is translated immediately. Note: the language on the left cannot be changed. This is the input language you selected during the Quick Setup.
Check the battery status. Powering off the IRISPen TM To power off the IRISPen , rapidly click the scanning tips three times against a surface. TM Note: when the IRISPen is inactive for 12 minutes, it auto powers off. TM 5. Troubleshooting Should you experience issues when using the IRISPen Air 7, tap the menu icon ( and Support. TM ) and select Help Tip: for a list of compatible devices, click the links to go to the IRISPen Air 7 section of the I.R.I.S.
Bluetooth Specifications Standard Frequency Range Bluetooth Low Energy Core 4.0 specification compliant Used in operation 2402 MHz – 2480 MHz Occupied block 2400 MHz – 2483.5 MHz Number of channels 40 channels, each 2 MHz wide Data Rate 1 Mbps Transmit Power (EIRP) 0.35 mW max Battery Specifications Type Single cell lithium-polymer (LiPo) Model GSP051050 Rated capacity 200mAh Rated voltage 3.7 V Maximum voltage 4.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This equipment has been certified to comply with the limits for a class B computing device, pursuant to FCC Rules. In order to maintain compliance with FCC regulations, shielded cables must be used with this equipment.