Mirra Pool Cleaning Robot Model 530 Owner’s Manual global.irobot.
IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL THE INSTRUCTIONS CAUTION: Do not plug the power supply into a grounded outlet or do not switch the pool cleaner “ON” if it is not fully immersed in water. Registration and Warranty Please visit www.irobot.com/register to register your product and activate your warranty. Operating the cleaner out of waterwill cause severe damage immediately and will result in loss of warranty.
Welcome Dear Mirra Owner, Thank you for choosing a new generation iRobot Mirra pool cleaning robot. You’re joining a very special community of people - 7.5 million worldwide and growing - who are discovering just how useful, convenient and straightforward having a home robot is. In fact, owners tend to like their robots so much they’ve even given them nicknames. We’re passionate about our robots too. Not surprisingly, given that making robots is all we’ve ever done in the 20 odd years of our existence.
Table of Contents Getting Started................................................................. 5 Maintenance and Adjustment.......................................... 6-7 Cleaning the Filter/ Changing the Rolling Brush.............. 8 Accessing and Cleaning the Propeller............................. 9 Operating Your Pool Cleaner............................................ 10-12 Troubleshooting................................................................ 13 Power Supply.......................
Getting Started 2 Soak wheels for 15 minutes 1 3.6m/11.8ft 15min. 3 5 12 cm (4.7 inch) 4 6 7 global.irobot.
Maintenance and Adjustment INTAKE VALVES ADJUSTMENT Adjust filter valve to get best suction on ground. Adjust filter valve to get best clearance on ground. PVA WHEELS SOAKING Soak wheels after extended period of storage. 15min.
Maintenance and Adjustment Continued FLOAT INSTALLATION Robot should turn 90 degrees on the first turn of a new cleaning cycle. Remove filter canister to access float block holder Adjust amount of float blocks to achieve desired turning behaviors. A2 A3 A4 A1 B2 B3 B1 B4 global.irobot.
Cleaning the Filter 1 2 3 4 6 7 8 3 4 It is recommended to clean the filter after each working-cycle.
Accessing and Cleaning the Propeller DISCONNECT THE ROBOT FROM THE POWER-SUPPLY BEFORE PERFORMING THIS ACTION Clean the propeller if experiencing poor suction. 1 2 3 4 6 7 8 9 5 10 Pump motor Propeller Clean here global.irobot.
Operating Your Pool Cleaner - Set Up 1. Place the power supply (transformer) at least 3.6 meters / 11.8 feet from the pool and atleast 12 cm / 4 Inch above the surface. The transformer will supply low voltage to the cleaner. 2. Uncoil the cable. 1 3.6m/11.8ft 4. P lug the cable into the power supply. Make sure the key on the plug corresponds exactly with the key slot on the socket of the power supply. (See details on the next page) 5. P lug the power supply into a grounded outlet.
Operating Your Pool Cleaner - Plugging the Cable Plug Type To plug the cable (Fig A) into the socket on the power supply (Fig. B), please do the following: 1. Prepare the plug as seen in (Fig. C) with the key and 3 outside slots exactly as shown. 2. Fit exactly the key and the slots from cable plug with the corresponding key and slots from the power supply socket. (Fig. D) 3. Push the plug all the way into the socket of the power supply. 4.
Operating Your Pool Cleaner - Power Button a. P ower LED The blue LED flashes when the power supply is in standby mode and lights continuously when the pool cleaner is operating. b. “ CLEAN” button The button switches between “ON” and “STANDBY”. IMPORTANT- After every cycle the pool cleaner will automatically go to “standby”. In case you want to turn the machine off during the working cycle, press the CLEAN button once and the LED will start flashing, indicating that the machine has stopped running.
Troubleshooting Guide Troubleshooting PLEASE CHECK THE FOLLOWING BEFORE CALLING YOUR SERVICE CENTER Before troubleshooting, the pool cleaner must be disconnected from the power supply and the power supply must be unplugged from the electrical outlet to prevent damage to the unit and possible personal injury. 1. Unit does not pump water or move: a) Check to see if electric outlet has power. b) Check if transformer is plugged into a grounded outlet and the cable assembly is plugged into the transformer.
Power Supply Grounding The power supply must be connected to a grounded 3 conductor socket. The main power supply must be connected via a GFCI (ground fault circuit interrupter) or RCD (residual current device) having a rated residual operating current not greater than 30mA. Physical Dimensions (W * D * H) _______ 273mm * 242mm * 90mm 10.75in * 9.53in * 3.54in Weight ___________________ 1.9 Kg / 4.19 lbs Electrical Input rating ________________ 100-240V~, 50/60Hz, 210W Output rating _______________ 29V, 6.
Troubleshooting Guide Declaration of Conformity Test Standards EN60335-1 Household and similar electrical appliances-Safety Part 1: General requirements EN60335-2-41 Household and similar electrical appliances-Safety Part 2 Particular requirement for pumps EN62233 Electromagnetic fields-Methods for evaluation and measurement FCC Notice: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Get Robot Updates Register your Robot! Go to global.irobot.com iRobot Customer Care USA If you have questions or comments about this product please contact iRobot before contacting a retailer. Please visit the iRobot home support site at www.irobot.com/support for support tips, frequently asked questions, or information about accessories and other iRobot products. Should you still need assistance: iRobot Customer Care Outside USA & Canada Visit global.irobot.