福建飞毛腿动力科技有限公司 Fujian SCUD Power Technology Co., Ltd. V1.
福建飞毛腿动力科技有限公司 Fujian SCUD Power Technology Co., Ltd. V1.4 修改历史 Revision History 版本 日期 描述 修订者 Version Date Description Reviser V1.0 2023.08.25 Original release 谢煇 1、增加结构外形图. 2、修改最大充电电流参数：0~15℃充电电流 由840mA变更为875mA;15~50℃充电电流由 V1.1 2023.08.30 1200mA变更为1250mA. 谢煇 3、实际重量由200g变更为待定 添加一级过充恢复条件:充电器在位移除后电 压小于 4.175V 解除 1、PCB Layout 变更：TP19 测试点、线束焊盘 V1.2 2023.09.27 P+、P-、T 位置调整 2、Weight (g) /重量：About 240g 谢煇 3、涉及到 0.2 C5A 充放电改为 0.5A 充放电 出厂电压调整为 15V~15.9V，About 80%~90% V1.3 2023.10.20 V1.4 2023.
福建飞毛腿动力科技有限公司 Fujian SCUD Power Technology Co., Ltd. V1.4 Contents /内容 1. Scope/范围 ............................................................................ 4 2. Standard compliance/参考标准 ............................................................ 4 3. Product name and model/产品型号名称 .....................................................4 3.1 Product Name/产品名称 ........................................................................................................................4 3.2 Product Model/产品型号 ..
福建飞毛腿动力科技有限公司 Fujian SCUD Power Technology Co., Ltd. V1.4 1. Scope/范围 The specification describes the requirements for ABL-G Li-ion Cylindrical Rechargeable Battery Pack. supplied by Fujian SCUD Power Technology Co., Ltd. 本规格书适用于 ABL-G 锂离子电池组，由福建飞毛腿动力科技有限公司生产。 2. Standard compliance/参考标准 GB31241-2022、CB、UN38.3 等 3. Product name and model/产品型号名称 3.1 Product Name/产品名称 Li-ion Cylindrical Rechargeable Battery Pack 3.2 Product Model/产品型号 ABL-G 3.3 Series parallel Construction/串并联结构 4S1P 4.
4.2.8 福建飞毛腿动力科技有限公司 Fujian SCUD Power Technology Co., Ltd. Standard Charge Current 500mA /标准充电电流 875mA 4.2.9 Max. Charging Current /最大充电电流 1250mA 4.2.10 Standard Discharge Current /标准放电电流 500mA 4.2.11 Max. Continuous Discharge Current /最大持续放电电流 4000mA 4.2.12 Max. Pulse Discharge Current /最大瞬时放电电流 5.625A（<189ms） 4.2.13 Weight (g) /重量 About 4.2.14 Shipping OCV /出厂电压 15.5-15.9V 4.2.15 Internal impedance /内阻 Operation 4.2.16 4.2.
福建飞毛腿动力科技有限公司 Fujian SCUD Power Technology Co., Ltd. Environment Unless otherwise specified, all test stated in this /环境 specification are conducted at ： V1.4 1)temperature: 23±2℃; 2)humidity: ≤75% RH ; 3)atmospheric pressure：86kPa~106kPa /除非另有规定，本规范中规定的所有试验均在： 1)温度:23±2℃; 2)湿度:≤75%; 3)大气压力:86 kpa ~ 106 kpa Measure Equipment 1）Ammeter and Voltmeter: The ammeter and voltmeter /测试设备 should have an accuracy of the grade 0.2 or higher. 2)Slide caliper: The slide caliper should have less than 0.
福建飞毛腿动力科技有限公司 Fujian SCUD Power Technology Co., Ltd. V1.4 High Temperature After standard charged, battery should be stored in a Discharge capacity discharge temperature-controlled environment at 55±2℃ for 2 ≥90% Rated capacity /高温放电 hours. after storage, battery should be discharged with /放电容量≥90%额定容量 0.5A to end of discharging voltage. /电池组按标准充电结束后，将电池组放入 55℃±2℃的 高温箱中恒温 2h，然后以 0.
福建飞毛腿动力科技有限公司 Fujian SCUD Power Technology Co., Ltd. V1.4 Cycle Life Charging/discharging is repeated in the below condition The battery capacity should /循环寿命 @25℃±3℃. be more than 80% of Initial Charge:16.6V/0.5A to CC/CV charging, cut off current capacity after 600 cycles. 50mA. Discharge: 0.5A discharge to End of discharge voltage. /循环 600 次后电池组容量 Pack is to be rested for 0.5 hour after charged and 为初始容量 80%以上。 discharge.
福建飞毛腿动力科技有限公司 Fujian SCUD Power Technology Co., Ltd. V1.4 Vibration Cells and batteries are firmly secured to the platform OCV ≥ 90% initial OCV (open /震动试验 of the vibration machine without circuit voltage). The battery should distorting the cells in such a manner as to faithfully be no leakage, no venting, no transmit the vibration. The vibration should be a rupture, no fire or no explosion.
福建飞毛腿动力科技有限公司 Fujian SCUD Power Technology Co., Ltd. V1.4 Acceleration Test A standard charged battery is to be firmly secured to The battery should be no fire, no /加速度冲击 the platform of acceleration test equipment. explosion, or no leakage. Each shock is to be applied in a direction normal to /电池组应不起火，不爆炸，不漏液。 the face of the battery. For each shock the cell is to be accelerated in such a manner that during the initial 3 milliseconds the minimum average acceleration is 75g.N.
福建飞毛腿动力科技有限公司 Fujian SCUD Power Technology Co., Ltd. V1.
福建飞毛腿动力科技有限公司 Fujian SCUD Power Technology Co., Ltd. V1.4 1st Overcharge release voltage /一级过充保护恢复电压 V 4.05 4.075 4.10 1st Over discharge detection voltage /一级过放电保护电压 V 2.77 2.80 2.83 1st Over discharge detection delay time /一级过放电保护延迟时间 s 0.80 1.00 1.20 1st Over discharge release voltage /一级过放电保护解除电压 V 2.97 3.0 3.03 Charge over current detection current /充电过电流保护值 A 1.875 2.5 3.125 Charge over current detection delay time /充电过电流保护延迟时间 s 0.40 0.50 0.
福建飞毛腿动力科技有限公司 Fujian SCUD Power Technology Co., Ltd. V1.4 Discharge under temperature protection /放电低温保护值 ℃ -23 -20 -17 Discharge under temperature protection release /放电低温保护恢复值 ℃ -18 -15 -12 Temperature protection current delay time /温度保护检测延时 s 1 2 3 0V charging disable/ 0V 充电禁止电压 V 1.4 1.5 1.6 Current consumption /工作消耗电流 μA - 30 50 Standby Current /休眠电流 μA - - 30 Output NTC/输出端 NTC kΩ - 10 - 2st Over charge detection voltage /二段过充电保护电压 V 4.275 4.300 4.
福建飞毛腿动力科技有限公司 Fujian SCUD Power Technology Co., Ltd. V1.4 15 C1, C3, C5, C6, C7, C8, C10, C11, C12, C13, C14, C15, C16, C17 Capacity 0402-50V-104-K-X7R 14 Yageo 16 C4 Capacity 0402-25V-27nF-K-X7R 1 Yageo 17 NTC1，NTC2 NTC 1206-10K-3435-12mm-±1%带线 2 Newlife 18 B+,B-,B1,B2,B3 贴装镍片 NP-0.
福建飞毛腿动力科技有限公司 Fujian SCUD Power Technology Co., Ltd. V1.4 PCB Layout 5.3.4.1 PCB Toplayer: Bottomlayer: Top Silkscreen & Paste: 本文中所有内容均为飞毛腿动力的机密信息！未经允许不得散布 SCUD power confidential information! Do not distribute without written permission from SCUD Power.
福建飞毛腿动力科技有限公司 Fujian SCUD Power Technology Co., Ltd. V1.4 Bottom Silkscreen & Paste: 本文中所有内容均为飞毛腿动力的机密信息！未经允许不得散布 SCUD power confidential information! Do not distribute without written permission from SCUD Power.
福建飞毛腿动力科技有限公司 Fujian SCUD Power Technology Co., Ltd. V1.4 5.4 Safety Requirement/安全性能 Items Conditions and others Charge Over Voltage The standard charged battery is continue to be Performances The battery should be no fire, no Protection charged with maximum charging current to n*6V explosion or no leakage. /过压充电 or the highest possible voltage(Choose the best 电池组应不起火，不爆炸，不漏液。 one), and keep the voltage by CV charging, until the protection circuit starts.
福建飞毛腿动力科技有限公司 Fujian SCUD Power Technology Co., Ltd. V1.4 External Short The test should be conducted under 25±5℃. The battery should be no fire, no Circuit The standard charged battery is to be explosion, no smoke or no leakage. /外部短路 short-circuited by connecting the positive and 电池组应不起火，不爆炸，不冒烟或 negative terminals of the battery with copper 漏液。 wire having a resistance about 80mΩ±20 mΩ, until the protection circuit starts.
福建飞毛腿动力科技有限公司 Fujian SCUD Power Technology Co., Ltd. V1.4 6 Mechanical characteristics/机械性能 6.1 Appearance and diagrams/外观和尺寸 Sheet 6 Appearance NO. 1 Item Dimension/外形尺寸 Conditions and others Remark Refer to the structure diagram /参见机械结构图表 2 Connection PIN/接触极片 Refer to the structure diagram /参见机械结构图表 3 The material of liner/衬垫材料 Combustion proof grade:V0 /阻燃等级：V0 4 Mark and Label/标签 Refer to the attachment of battery label.
福建飞毛腿动力科技有限公司 Fujian SCUD Power Technology Co., Ltd. V1.0 本文中所有内容均为飞毛腿动力的机密信息！未经允许不得散布。 SCUD power confidential information! Do not distribute without written permission from SCUD Power.
福建飞毛腿动力科技有限公司 Fujian SCUD Power Technology Co., Ltd. 6.2 V1.0 Connector/连接器定义 本文中所有内容均为飞毛腿动力的机密信息！未经允许不得散布。 SCUD power confidential information! Do not distribute without written permission from SCUD Power.
福建飞毛腿动力科技有限公司 Fujian SCUD Power Technology Co., Ltd. 本文中所有内容均为飞毛腿动力的机密信息！未经允许不得散布 SCUD power confidential information! Do not distribute without written permission from SCUD Power. V1.
福建飞毛腿动力科技有限公司 Fujian SCUD Power Technology Co., Ltd. V1.4 7 Label/标签 本文中所有内容均为飞毛腿动力的机密信息！未经允许不得散布 SCUD power confidential information! Do not distribute without written permission from SCUD Power.
福建飞毛腿动力科技有限公司 Fujian SCUD Power Technology Co., Ltd. V1.4 8 Package/包装 本文中所有内容均为飞毛腿动力的机密信息！未经允许不得散布 SCUD power confidential information! Do not distribute without written permission from SCUD Power.
福建飞毛腿动力科技有限公司 Fujian SCUD Power Technology Co., Ltd. 本文中所有内容均为飞毛腿动力的机密信息！未经允许不得散布 SCUD power confidential information! Do not distribute without written permission from SCUD Power. V1.
福建飞毛腿动力科技有限公司 Fujian SCUD Power Technology Co., Ltd. V1.4 Others/其他 9 9.1 Odor/气味 The battery do not product special smell or harmful odor./本电池组不会产生特别或有害的气味 9.2 Protection for Environment/环境保护 The material used for packing should meet the criterion to protect environment RoHs 2.0、Reach. /封装电池组所用材料须全部符合环境保护标准 RoHs 2.0、Reach . 10 Warning and notice/注意事项 1、 Do not put the battery into a fire, or heat the battery. /请勿将电池组放入火中或加热电池组。 2、 Do not store the battery in high temperature environment.
福建飞毛腿动力科技有限公司 Fujian SCUD Power Technology Co., Ltd. V1.4 1、Before using the battery, carefully read and follow battery specification and the information on the surface of the batteries./使用电池组前，请仔细阅读和遵守电池组组规格书，以及电池组组表面的信息。 2、Children should not be allowed to play with them. /避免儿童玩弄电池组。 3、The batteries should only be charged with a matching charger. /本电池组只能使用配套充电器充电。 4、Caution – The battery used in this device may present a risk of fire or chemical burn if mistreated.
