2020 Installation Instructions

ManualsBrandsIron-A-Way ManualsIroning42 Inch Ironing Center with 90° Swivel Ventilated Board, Hot Iron Storage, 60-Minute Safety Timer, Storage Shelves, Hanger Bar, Spotlight, Adjustable Swivel Brackets, Built-In Safety Switch, and UL Listed: No Door

INSTALLATION MANUAL

IRONING CENTER

#10 x 1 1/2” Wood Screws (2)

#14 x 2 1/2” Philips Screws (2)

RECESSED INSTALLATION

#14 x 4” Wood Screws (2)

SURFACE MOUNT INSTALLATION

SWIVEL MODELS

AE-46 ANE-46 AE-42 ANE-42 UD-42

SUPPLIED PARTS

#10 x 1 1/2” Wood Screws (4)

RECESSED INSTALLATION

#14 x 4” Wood Screws (2)

IAW-42 ONLY

#14 x 2 1/2” Wood screws (2)

SURFACE MOUNT INSTALLATION

NONSWIVEL MODELS

E-46 NE-46 E-42 NE-42 IAW-42

Carpenter’s Level

Tape Measure

Utility Knife

Drill

1/8” Drill Bit

3/16” Drill Bit

(Surface Mount Installation)

Small Flat Head Screwdriver

Safety Glasses

Optional:

Stud Finder

1/4” Nut Driver

TOOLS NEEDED

pg. 2 | Pre-Installation

pg. 3 | Recessed Mount

pg. 4 | Surface Mount

pg. 7 | Electrical

Quick Reference:

Swivel Models Non-Swivel Models

pg. 2 | Pre-Installation

pg. 5 | Recessed Mount

pg. 6 | Surface Mount

pg. 7 | Electrical

Iron-A-Way

1-800-536-9495

support@ironaway.com

220 W. Jackson, Morton, IL 61550

Summary of content (8 pages)

PAGE 1
IRONING CENTER INSTALLATION MANUAL SUPPLIED PARTS TOOLS NEEDED SWIVEL MODELS Carpenter’s Level Tape Measure Utility Knife Drill 1/8” Drill Bit 3/16” Drill Bit (Surface Mount Installation) Small Flat Head Screwdriver Safety Glasses AE-46 ANE-46 AE-42 ANE-42 UD-42 RECESSED INSTALLATION #10 x 1 1/2” Wood Screws (2) #14 x 2 1/2” Philips Screws (2) SURFACE MOUNT INSTALLATION #14 x 4” Wood Screws (2) NON-SWIVEL MODELS E-46 NE-46 E-42 NE-42 IAW-42 Optional: Stud Finder 1/4” Nut Driver RECESSED INSTALLATION
PAGE 2
PRE-INSTALLATION Please follow these Pre-Installation steps to ensure your ironing board will work properly in the installation location you have selected. STEP ONE: Ironing Board Clearance Begin by ensuring your desired installation location has adequate space for your selected model. Choose Recessed Mount or Surface Mount.
PAGE 3
ADJUSTABLE SWIVEL RECESSED MOUNT INSTALLATION Models | AE-46, ANE-46, AE-42, ANE-42, UD-42 STEP ONE: Determine Mounting Height Identify your desired ironing board height (typical ironing board is 33”-35” high). Then subtract the number below based on the length of your model’s ironing board to determine mounting height (FIG 1.1). Take into consideration the adjusted position of your ironing board, which is 4” higher than the normal, default position.
PAGE 4
ADJUSTABLE SWIVEL SURFACE MOUNT INSTALLATION Models | AE-46, ANE-46, AE-42, ANE-42, UD-42 STEP ONE: Determine Mounting Height Identify your desired ironing board height (typical ironing board is 33”-35” high). Then subtract the number below based on the length of your model’s ironing board to determine mounting height (FIG 2.1). Take into consideration the adjusted position of your ironing board, which is 4” higher than the normal, default position.
PAGE 5
NON-SWIVEL RECESSED MOUNT INSTALLATION Models | E-46, NE-46, E-42, NE-42 STEP ONE: Determine Mounting Height Identify your desired ironing board height (typical ironing board is 33”-35” high). Then subtract the number below based on the length of your model’s ironing board to determine mounting height (FIG 1.1).
PAGE 6
NON-SWIVEL SURFACE MOUNT INSTALLATION Models | E-46, NE-46, E-42, NE-42, IAW-42 STEP ONE: Determine Mounting Height Identify your desired ironing board height (typical ironing board is 33”-35” high). Then subtract the number below based on the length of your model’s ironing board to determine mounting height (FIG 2.1).
PAGE 7
ELECTRIC INSTALLATION Models | AE-46, E-46, AE-42, E-42, UD-42 ATTENTION: TURN OFF POWER AT SERVICE ENTRANCE BEFORE INSTALLING, WIRING, OR SERVICING THIS PRODUCT ITEMS TO NOTE Instructions for electrical models ONLY. DO NOT attempt to install your own outlet or electrical hook-up on a non-electrical model. All electrical work must be done in accordance with all applicable electrical codes. SUPPLY LINE: 110 Volt/15 Amps STEP ONE: Prepare Electrical Raceway TURN POWER OFF AT SERVICE ENTRANCE.
PAGE 8
Have installation questions? We’re here to help! 1-800-536-9495 support@ironaway.