OWNER’S MANUAL Power Tower 6880.1‐011516 6880.1-100715 The specifications of this product may vary from this photo and are subject to change without notice. IRONMAN, IRONMAN TRIATHLON and M-DOT are registered trademarks of World Triathlon Corporation. This product is licensed by the World Triathlon Corporation.
TABLE OF CONTENTS SERVICE-------------------------------------------------------------------- 2 LABEL PLACEMENT----------------------------------------------------- 3 PRODUCT SAFETY------------------------------------------------------- 4 ASSEMBLY PREPARATION-------------------------------------------- 5 EXPLODE DRAWING--------------------------------------------------- 7 HARDWARE PACK-------------------------------------------------------- 8 PART LIST------------------------------------------
SERVICE IMPORTANT: FOR NORTH AMERICA ONLY For damage or defective product, questions, replacement parts or any other service support, please contact our customer service department (8:00 AM - 5:00 PM Pacific Standard Time, Open Daily) by below methods: For Best Service Email: Service@paradigmhw.com * Website: www.paradigmhw.
3 Paradigm Health and Wellness, Inc. 1189 Jellick Ave. City of Industry CA 91748, USA materiales de este artículo se describen según las leyes. NO. DE REG VA25302 (CN) MATERIAL COMPLETAMENTE NUEVO COMPUESTO DE 100% RELLENO DE ESPUMA DE POLIURETANO. SE SANCIONARÁ LEGALMENTE A QUIENES QUITEN ESTA ETIQUETA. SOLO EL CONSUMIDOR PODRÁ QUITARLA. Paradigm Health and Wellness, Inc. 1189 Jellick Ave. City of Industry, CA 91748 USA Cette étiquette est apposée conformément aux lois Canadiennes.
PRODUCT SAFETY WARNING: Before using this equipment you should consult with your personal physician to see if the Ironman Power Tower is appropriate for you. Do not use this equipment without your physician’s approval.
ASSEMBLY PREPARATION Warning: It is highly recommend that you have assistance during the assembly of the IRONMAN strength equipment. 1. Tools for assembly: General tools you may needed for the assembly of the IRONMAN strength equipment. Metric Allen Key Set Metric Wrench Set and Adjustable Wrench Flat Screwdrivers Phillips Screwdrivers Rubber Mallet Silicone Spray Oil 2. Insert bolts into the frame as illustrated in the drawing of each of the steps. 3.
6
EXPLODE DRAWING 7
HARDWARE PACK 8
PART LIST Part# Description Q’ty. Part# Description Q’ty. A Base Beam 2 52 Washer D13.5xD24x2.5 52 B Lower Post 2 56 Washer D16xD8.4x1.6 7 C Upper Crossbeam 1 57 D Lower Crossbeam 1 58 E Adjustable Handlebar 2 76 Nylon Nut M12 26 F Wide Grip Pull Up Bar 2 103 Locking Pin Φ8x107 2 G Close Grip Pull Up Bar 2 120 Big End Cap Φ70*Φ21*38 2 H Grip Post 2 131 Domed End Cap Φ32xt2.0 8 I-R Right Dip Bar 1 132 Domed End Cap Φ50xt2.
STEP 1 1A. Attach the Lower Crossbeam (D) between the two Base Beams (A) and two Mounting Plates (K) by using: 8 - (52) Washer D13.5xD24x2.5 4 - (7) Hex Bolt M12x1.75x80L 4 - (76) Nylon Nut M12 Thoroughly tighten the hardware once complete. Tip: Install the Base Beams (A) with the Ironman logo facing outward. Tip: The Lower Crossbeam (D) can be mounted in three different positions. There are additional holes towards the rear of the holes which this step instructs for assembly.
STEP 1 *For reference only. Wrench 2PC NO. 7 Hex Head Bolt M12x1.75x80L 4PCS NO. 76 Nylon Nut M12 4PCS 811 NO.52 Washer D13.5xD24x2.
STEP 2 2A. Attach both Lower Posts (B) to the two Base Beams (A) by using: 8 - (52) Washer D13.5xD24x2.5 4 - (7) Hex Bolt M12x1.75x80L 4 - (76) Nylon Nut M12 Thoroughly tighten the hardware once complete. Appearance upon completion of Step 2.
STEP 2 *For reference only. Wrench 2PC NO. 7 Hex Head Bolt M12x1.75x80L 4PCS NO. 76 Nylon Nut M12 4PCS 13 NO.52 Washer D13.5xD24x2.
STEP 3 3A. Insert one Upper Post (J) into the bracket of the Lower Post (B). Continue holding the Upper Post (J) and align its holes with the holes of the Lower Post (B). Insert three Hex Bolts (17) all the way through the Lower Post (B) and Upper Post (J). Mount Upper Crossbeam (C) by inserting the threaded ends of the two Hex Bolts (17) sticking out of Lower Posts (B) and Upper Post (J). Attach all three parts by using: 6 - (52) Washer D13.5xD24x2.5 3 - (76) Nylon Nut M12 3 - (17) Hex Bolt M12x1.
STEP 3 *For reference only. Wrench 2PC NO. 17 Hex Head Bolt M12x1.75x85L 6PCS NO. 76 Nylon Nut M12 6PCS 15 NO.52 Washer D13.5xD24x2.
STEP 4 4A. Attach the Forearm Pad (P) to the RIGHT Dip Bar (I-R) as in image AA-2, using: 2 - (56) Washer D16xD8.4x1.6 2 - (57) Spring Washer D12.3xD8.1x2.1 2 - (19) Hex Bolt M8x1.25x70L Thoroughly tighten the hardware once complete. 4B. Attach the RIGHT Dip Bar (I-R) to the RIGHT Lower Post (B) by using: 4 - (52) Washer D13.5xD24x2.5 2 - (76) Nylon Nut M12 2 - (7) Hex Bolt M12x1.75x80L 4C. Attach a Grip Post (H) to the RIGHT Dip Bar (I-R) by using: 1 - (51) Washer D20xD10.5xT2.
STEP 4 *For reference only. Wrench 2PC NO. 7 Hex Head Bolt M12x1.75x80L 4PCS NO. 76 Nylon Nut M12 4PCS NO. 57 Spring Washer D12.3xD8.1x2.1 4PCS NO.19 Hex Bolt M8x1.25x70L 4PCS NO.18 Hex Bolt NO.58 Spring Washer M10x1.5x25L D15.4xD10.2x2.6 2PCS 2PCS NO.52 Washer D13.5xD24x2.5 8PCS NO.56 Washer D16xD8.4x1.6 4PCS NO.51 Washer D20xD10.
STEP 5 5. Attach the Backrest (M) to the Upper Crossbeam (C) at the by first aligning the screw holes and hand tightening the hardware listed below into place. Once all hardware has been inserted, fasten the hardware tightly. 2 - (19) Hex Bolt M8x1.25x70L 1 - (3) Hex Bolt M8x1.25x25L 3 - (57) Spring Washer D12.3xD8.1x2.1 3 - (56) Washer D16xD8.4x1.6 Thoroughly tighten the hardware once complete. Appearance upon completion of Step 5.
STEP 5 *For reference only. Wrench 2PC NO.19 Hex Bolt M8x1.25x70L 2PCS NO.3 Hex Bolt M8x1.25x25L 1PC NO.57 Spring Washer D12.3xD8.1x2.1 3PCS 19 NO.56 Washer D16xD8.4x1.
STEP 6 6A. Insert both Wide Grip Pull Up Bars (F) into the slots at the top of the Upper Posts (J) and attach by using: 4 - (7) Hex Bolt M12x1.75x80L 8 - (52) Washer D13.5xD24x2.5 4 - (76) Nylon Nut M12 6B. Attach the Close Grip Pull Up Bars (G) and Mounting Plates (L) to Upper Posts (J) by using: 4 - (7) Hex Bolt M12x1.75x80L 8 - (52) Washer D13.5xD24 x2.5 4 - (76) Nylon Nut M12 Thoroughly tighten the hardware once complete. 6C.
STEP 6 *For reference only. Wrench 2PC NO. 103 Locking Pin Φ8x107 2 PCS NO. 7 Hex Head Bolt M12x1.75x80L 8PCS NO. 76 Nylon Nut M12x1.75x12T 8PCS 21 NO.52 Washer D13.5xD24x2.
ADJUSTMENT Grip Post Adjustment: The Grip Posts (H) have two positions for mounting to the structure. For your comfort choose the position that suits the length of your forearm the best. Adjustable Handlebar Adjustments: The Adjustable Handlebars (E) can be used in any of the 1 inch holes available along the frame to allow for a variety of exercises. Warning: Always make sure that each Adjustable Handlebar (E) is securely held in place with a Locking Pin (103) before performing an excise with them.
WARRANTY MANUFACTURER’S LIMITED WARRANTY Paradigm Health & Wellness guarantees to the original purchaser that this product is free from defects in material and workmanship when used for the purpose intended, under the conditions that it has been installed and operated in accordance with Paradigm’s Owner’s Manual.
PART REQUEST FORM Paradigm Health & Wellness, Inc. EMAIL THIS FORM WITH YOUR RECIEPT OF PURCHASE TO Service@paradigmhw.