00 Ft. String Lights LightLight500W Halogen Work Light Owner’s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.
Thank you very much for choosing an Ironton™ product! For future reference, please complete the owner’s record below: Serial Number/Lot Date Code: ________________________________ Purchase Date: ____________________________________________ Save the receipt, warranty, and this manual. It is important that you read the entire manual to become familiar with this product before you begin using it. This light set is designed for certain applications only.
Table of Contents Intended Use .......................................................................................................................................... 4 Technical Specifications ...................................................................................................................... 4 Important Safety Information ............................................................................................................... 4 Specific Operation Warnings .......................
Intended Use The Ironton 100 Ft. String Lights feature 10 lamp holders with plastic lamp guards spaced 10 feet apart on a single 125V, 15 Amp, 14/3 cord with a grounded plug. The light set provides an even string of bright lighting. Technical Specifications Property Power Supply Max Current Consumption Cord String Length Specification 125 Volt AC 15 Amps 14/3 100 Feet Important Safety Information ⚠WARNING Read and understand all instructions.
Keep children and bystanders away from the work area while operating the tool. Do not allow children to handle the product. Be aware of all power lines, electrical circuits, water pipes, and other mechanical hazards in your work area. Some of these hazards may be hidden from your view and may cause personal injury and/or property damage if contacted. ⚠WARNING PERSONAL SAFETY Stay alert, watch what you are doing, and use common sense when operating the tool.
the tool itself. Keep guards in place and in working order. Never operate the product without the guards in place. Do not leave the tool running unattended. Specific Operation Warnings ⚠WARNING Electrical Shock and Fire Hazard. Do not exceed the marked lamp holder wattage or string maximum wattage including any additional string loads. Do not plug in an additional light or appliance that exceeds 375 watts. Electric shock hazard.
Use plug cover when not in use. Not for use by or around children. Grounding ⚠WARNING This machine must be grounded while in use to protect the operator from electrical shock. This unit is equipped with an electrical cord that has an equipment grounding conductor and a grounding plug. The plug MUST be plugged into a matching receptacle that is properly installed and grounded in accordance with ALL local codes and ordinances. DO NOT MODIFY THE PROVIDED PLUG.
Extension Cords ⚠WARNING USE A PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage, resulting in loss of power and cause overheating. Be sure your extension cord is properly wired and in good condition. Always replace a damaged extension cord or have it repaired by a qualified person before using it.
Main Parts of Light Set Reference 1 2 Subassembly 100ft String Light Set Lamp Guards Assembly Instructions ⚠WARNING This light set must be used with the lamp guards installed. Make sure the power is turned off. There is a risk of accidental starting, resulting in serious personal injury. Deviation from the assembly instructions may result in a risk of fire or electric shock. The light string must be supported every 10 feet. Do not use the conductors to support the light set.
Before Each Use ⚠WARNING The light string must be supported every 10 feet. Do not use the conductors to support the light set. Hooks or a steel cable must be used. Always check damaged or worn out parts before using the work light. Broken parts will affect the work light operation. Inspect the general condition of the light set. Check for: Loose hardware, Damaged cord/electrical wiring, Cracked or broken parts. Any other condition that may affect its safe operation.
close proximity to heart pacemaker could cause pacemaker interference or pacemaker failure. In addition, people with pacemakers should: Avoid operating alone. Properly maintain and inspect to avoid electrical shock. Properly ground the power cord. Ground Fault Circuit Interrupter (GFCI) should also be implemented – it prevents sustained electrical shock. Replacing Bulbs Unlock the button on the lamp guard and remove the broken bulb. Insert the bulb (not included) into the socket.
Maintenance ⚠WARNING If the supply cord of this light is damaged, it must be replaced only by a qualified service technician. Procedures not specifically explained in this manual must be performed only by a qualified technician. Maintain the product by adopting a program of conscientious repair and maintenance in accordance with the following recommended procedures. It is recommended that the general condition of any tool be examined before it is used.
and both ends of electrical contacts are against the contacts on each end of bulb. Bulb may have been damaged in shipment. Check lamp with another bulb or check bulb with a continuity tester. If bad, replace bulb. Bulb is damaged.
Limited Warranty Northern Tool and Equipment Company, Inc. ("We'' or ''Us'') warrants to the original purchaser only (''You'' or ''Your'') that the Ironton product purchased will be free from material defects in both materials and workmanship, normal wear and tear excepted, for a period of 90 days from date of purchase. The foregoing warranty is valid only if the installation and use of the product is strictly in accordance with product instructions.
Distributed by: Northern Tool & Equipment Company, Inc. Burnsville, Minnesota 55306 www.northerntool.