7 Piece Car Polishing Kit Owner’s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.
® Thank you very much for choosing an Ironton product! For future reference, please complete the owner’s record below: Serial Number/Lot Date Code: ________________________________ Purchase Date: ____________________________________________ Save the receipt, warranty, and this manual. It is important that you read the entire manual to become familiar with this product before you begin using it. This car polishing kit is designed for certain applications only.
Table of Contents Intended Use .......................................................................................................................................... 4 Packaging Contents .............................................................................................................................. 4 Technical Specifications ...................................................................................................................... 4 Important Safety Information .................
Intended Use The Ironton 7 Piece Car Polishing Kit features a powerful 11 Amp, 7 inch polisher, plus all the accessories you'll need to polish your vehicle to a dazzling shine. The variable speed motor gives you ultimate control and the 5/8 inch spindle lets you change accessories quickly and easily.
⚠WARNING WORK AREA SAFETY Inspect the work area before each use. Keep work area clean, dry, free of clutter, and well-lit. Cluttered, wet, or dark work areas can result in injury. Using the product in confined work areas may put you dangerously close to cutting tools and rotating parts. Do not use the polisher where there is a risk of causing a fire or an explosion; e.g., in the presence of flammable liquids, gases, or dust.
Check for damaged parts before each use. Carefully check that the product will operate properly and perform its intended function. Replace damaged or worn parts immediately. Never operate the product with a damaged part. Do not use a product with a malfunctioning switch. Any power tool that cannot be controlled with the power switch is dangerous and must be repaired by an authorized service representative before using.
receptacle installed by a qualified electrician. CHECK with a qualified electrician or service person if you do not completely understand the grounding instructions, or if you are not sure the tool is properly grounded. Grounded Tools: Tools with 3-Prong Plugs Tools marked with Grounding Required have a 3-wire cord and 3-prong grounding plug. The plug must be connected to a properly grounded outlet.
As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of power and possible tool damage. The smaller the wire’s gauge number, the greater the capacity of the cord. For example, a 14gauge cord can carry a higher current than a 16-gauge cord.
Assembly Instructions ⚠WARNING Disconnect the polisher from the power supply. Do not operate the polisher with one hand only or without the side handle properly installed. Installing the Handle To install the side handle, screw the handle securely into the threaded hole on the right or left of the gear housing (as desired). Installing the Hook and Loop Backer Pad 1.
Installing and Removing an Accessory Note: Inspect the hook and loop backing pad and clean off any dirt or debris that is found. 1. Align the accessory over the backer pad. With the pad aligned, push down on the foam polishing pad to engage the hook and loop system. Confirm that the polishing pad is secured over the entire pad. 2. To remove the polishing pad, pull it off the backer pad. Before Each Use ⚠WARNING ALWAYS check for damaged or worn out parts before using the polisher.
Operating Instructions ⚠WARNING To reduce the risk of injury, user must read this instruction manual. To reduce the risk of injury, always wear eye and respiratory protection. Hold power tools by insulated gripping surfaces, when performing an operation where the cutting tool may contact hidden wiring or its own cord. Never place your hand near the rotating accessory. Accessories may kickback over your hand.
Polishing Note: Continuous operation of the polisher at low speeds for a long time will cause the motor to become overheated, possibly resulting in malfunction or tool failure. To cool the motor, occasionally run the polisher at high RPM under no load for short periods of time allowing the tool’s fan to cool the motor. Be careful not to obstruct the air vents located in the forward gear housing or in the rear handle, near the switch trigger.
Sanding For sanding, follow the polishing procedure. Note: Never use the sanding disc flat on the work surface; keep the abrasive disc at an angle of about 15 degrees while working the work piece surface. After Each Use ⚠WARNING Store the polisher in a secure place out of the reach of children. After switching off the polisher, the wheel will continue to rotate. Do not release your grip on the polisher until the wheel comes to a complete stop.
Maintain the polisher by adopting a program of conscientious repair and maintenance in accordance with the following recommended procedures. It is recommended that the general condition of any tool be examined before it is used. Keep your tool in good repair. Keep handles dry, clean, and free from oil and grease. The following chart is based on a normal operation schedule. Maintenance Interval Maintenance Point Daily before operating Inspect the general condition of the polisher.
Parts Diagram Parts List Reference 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Part Description Cap Lock Pin Spring Washer 5.6 x 0.6 Gear Box Oil Bearing Driven Gear Washer 30.1 x 1.2 Bearing 6001 Gear Base Dustproof Washer Principal Axis Polisher Disc Screw Washer GB/T93-1987 Tapping Screw ST4.
Reference 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 Part Description Bearing Clip Screw Rotor Bearing 608 Decouple Ring Lead Wind Ring Housing Stator Tapping Screw ST4.2X68 Washer GB/T93-1987 Right Handle Base Left Handle Base Tapping Screw ST4.
Limited Warranty Northern Tool and Equipment Company, Inc. ("We'' or ''Us'') warrants to the original purchaser only (''You'' or ''Your'') that the Ironton product purchased will be free from material defects in both materials and workmanship, normal wear and tear excepted, for a period of one year from date of purchase. The foregoing warranty is valid only if the installation and use of the product is strictly in accordance with product instructions.
Distributed by: Northern Tool & Equipment Company, Inc. Burnsville, Minnesota 55306 www.northerntool.
