Angle Grinder Holder Owner’s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.
Thank you very much for choosing an Ironton™ product! For future reference, please complete the owner’s record below: Serial Number/Lot Date Code: ________________________________ Purchase Date: ____________________________________________ Save the receipt, warranty, and this manual. It is important that you read the entire manual to become familiar with this product before you begin using it. This angle grinder holder is designed for certain applications only.
Table of Contents Intended Use .......................................................................................................................................... 4 Packaging Contents .............................................................................................................................. 4 Technical Specifications ...................................................................................................................... 4 Important Safety Information .................
Intended Use The Ironton Angle Grinder Holder is designed to hold most common 4 1/2 inch or 5 inch grinders with side handles without modifications. It turns your portable angle grinder into a metal-cutting chop saw which makes it a perfect tool for cutting tubing, bar stock, and rebar.
Cluttered, wet, or dark work areas can result in injury. Using the product in confined work areas may put you dangerously close to cutting tools and rotating parts. Do not use the product where there is a risk of causing a fire or an explosion; e.g., in the presence of flammable liquids, gases, or dust. The product can create sparks, which may ignite the flammable liquids, gases, or dust. Do not allow the product to come into contact with an electrical source.
the power switch is dangerous and must be repaired by an authorized service representative before using. Disconnect the power/air supply from the product and place the switch in the locked or off position before making any adjustments, changing accessories, or storing the tool. Such preventive safety measures reduce the risk of starting the tool accidentally. Store the holder when it is not in use. Store it in a dry, secure place out of the reach of children.
Assembly Steps 1. Unscrew the two bolts on the jaw clamps and use these two bolts to attach the jaw clamps on the stand. Finger-tighten the two bolts. Do not fully tighten them as you may need to adjust the distance between these two jaw clamps according to your angle grinder size (images 2 and 3). 2. Unscrew the two bolts (A) that are already assembled on the base (image 4).
3. Assemble the stand on the base by using the two bolts (A). Finger-tighten these two bolts (image 5). 5 4. Insert the M10 x 68mm bolt (with nut) (B) and M10 x 50mm bolt (with nut) (C) into the two holes on the stand. Finger-tighten the two bolts (image 5). 5. The 2 M10 x 30mm bolts with nuts, 2 M8x25mm bolts with nuts, 2 M6x25mm bolts with nuts, and 4 plastic spacers included in the pack are for assembling different sizes of angle grinders on the stand.
6. Place the head of your angle grinder between the two jaw clamps. You may need to adjust the distance between the two jaw clamps according to the size of the angle grinder head (image 8). Use the most appropriate bolts you chose to attach the angle grinder head on the jaw clamps. Use an adjustable wrench (not included) to fully tighten the bolts. 7. Use a hex key (not included) to fully tighten the two bolts on the jaw clamps (image 9). 8.
. Loosen the nut on the handle and assemble the handle on the stand (image 12). 11. Unscrew the locking nut on the lever (image 13). 12. Insert the lever into the hole on the safety guard and screw the locking nut on and fully tighten it. Fully tighten the other nut on the lever (image 14). 13. Unscrew bolt D on the stand (image 15). 14. Insert the lever into the hole on the stand (image 16).
15. Reassemble bolt D on the stand and fully tighten using an adjustable wrench (not included) (image 17). Before Each Use ⚠WARNING Check for loose or damaged parts and replace as needed. Make sure the holder is in good working condition. Operating Instructions ⚠WARNING Always unplug grinder before loosening and repositioning the grinder blade guard or when making other adjustments. Only use on flat, level surfaces. Bolt down the stand before installing the grinder.
1. Adjust the holder to the desired angle and tighten the object on the base. 2. Connect to power. Hold the handle (19) firmly and slowly push down the angle grinder. After Each Use ⚠WARNING Store the holder in a dry and clean place. Clean the surface with a damp cloth only. Keep the tool away from children.
Maintenance Maintain the holder by adopting a program of conscientious repair and maintenance in accordance with the following recommended procedures. It is recommended that the general condition of any tool be examined before it is used. Keep your tool in good repair. Keep handles dry, clean, and free from oil and grease. The following chart is based on a normal operation schedule. Maintenance Interval Maintenance Point Clean the holder with a damp cloth.
Parts Diagram Page 14 of 18
Parts List Part Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 Part Description Base Bracket Hex Screw (M8 x 14) Spindle (10x59) Flange Stand Spring Washer (¢14×¢6.3×1.
Replacement Parts For replacement parts and technical questions, please call Customer Service at 1-800-222-5381. Not all product components are available for replacement. The illustrations provided are a convenient reference to the location and position of parts in the assembly sequence. When ordering parts, the following information will be required: item description, item model number, item serial number/item lot date code, and the replacement part reference number.
Limited Warranty Northern Tool and Equipment Company, Inc. ("We'' or ''Us'') warrants to the original purchaser only (''You'' or ''Your'') that the Ironton product purchased will be free from material defects in both materials and workmanship, normal wear and tear excepted, for a period of one year from date of purchase. The foregoing warranty is valid only if the installation and use of the product is strictly in accordance with product instructions.
Distributed by: Northern Tool & Equipment Company, Inc. Burnsville, Minnesota 55306 www.northerntool.
