22In. Oscillating Pedestal Fan Owner’s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.
Thank you very much for choosing an Ironton™ product! For future reference, please complete the owner’s record below: Serial Number/Lot Date Code: ________________________________ Purchase Date: ____________________________________________ Save the receipt, warranty, and this manual. It is important that you read the entire manual to become familiar with this product before you begin using it. This fan is designed for certain applications only.
Table of Contents Intended Use .......................................................................................................................................... 4 Technical Specifications ...................................................................................................................... 4 Important Safety Information ............................................................................................................... 4 Specific Operation Warnings .......................
Intended Use The Ironton 22 Inch Oscillating Pedestal Fan is designed to provide cooling and powerful air circulation. Technical Specifications Item No. Size Volts/Hz. Current (A) CFM RPM 57936 22 inch 120V/60Hz. 1.35 4500 1450 Important Safety Information ⚠WARNING Read and understand all instructions. Failure to follow all instructions may result in serious injury or property damage.
Be aware of all power lines, electrical circuits, water pipes, and other mechanical hazards in your work area. Some of these hazards may be hidden from your view and may cause personal injury and/or property damage if contacted. ⚠WARNING PERSONAL SAFETY Stay alert, watch what you are doing, and use common sense when operating the tool. Do not use the tool while you are tired or under the influence of drugs, alcohol, or medication.
Specific Operation Warnings ⚠WARNING To prevent serious injury or property damage, read and understand owner’s manual before operating. Electric shock hazard. Do not expose the unit or the plug to water or rain. Do not use the fan near a water source such as a swimming pool, bathtub, or shower. Be sure the fan is properly grounded. Do not use this fan with any solid state speed control device. Only plug the unit into a power outlet with the same voltage as rated voltage of it.
down, grounding provides a low resistance path to carry electricity away from the user, reducing the risk of electric shock. (See Figure A.) The grounding prong in the plug is connected through the green wire inside the cord to the grounding system in the tool. The green wire in the cord must be the only wire connected to the tool’s grounding system and must never be attached to an electrically live terminal.
Nameplate AMPS 0-6 6-10 10-12 12-16 Minimum Wire Size Of Extension Cords Cord Length 25' 50' 100' 150' 18 AWG 16 AWG 16 AWG 14 AWG 18 AWG 16 AWG 14 AWG 12 AWG 16 AWG 16 AWG 14 AWG 12 AWG 14 AWG 12 AWG NOT RECOMMENDED When using more than one extension cord to make up the total length, make sure each cord contains at least the minimum wire size required. If you are using one extension cord for more than one tool, add the nameplate amperes and use the sum to determine the required minimum cord size.
3. Lock the fan head by two knobs as shown. Before Each Use Place the fan on a safe, flat surface where it cannot fall or be pulled by the cord.
Operating Instructions ⚠WARNING Electric shock hazard. Do not expose the unit or the plug to water or rain. Do not use the fan near a water source such as a swimming pool, bathtub, or shower. Be sure the fan is properly grounded. Do not use this fan with any solid state speed control device. Only plug the unit into a power outlet with the same voltage as rated voltage of it. Rotating blade hazard. Keep hands clear to avoid serious injury.
Troubleshooting Failure Fan fails to operate Excessive vibration Possible Cause Corrective Action Fan may not be plugged in. Make sure the fan is plugged in and the electrical outlet is working properly. There may be some obstructions in the fan. Check for any obstruction. If you find an obstruction, turn the fan “OFF”. Unplug the fan and carefully remove the obstruction. Plug the fan in and turn it on again, referring to the OPERATION INSTRUCTIONS.
Replacement Parts For replacement parts and technical questions, please call Customer Service at 1-800-222-5381. Not all product components are available for replacement. The illustrations provided are a convenient reference to the location and position of parts in the assembly sequence. When ordering parts, the following information will be required: item description, item model number, item serial number/item lot date code, and the replacement part reference number.
Limited Warranty Northern Tool and Equipment Company, Inc. ("We'' or ''Us'') warrants to the original purchaser only (''You'' or ''Your'') that the Ironton product purchased will be free from material defects in both materials and workmanship, normal wear and tear excepted, for a period of one year from date of purchase. The foregoing warranty is valid only if the installation and use of the product is strictly in accordance with product instructions.
Distributed by: Northern Tool & Equipment Company, Inc. Burnsville, Minnesota 55306 www.northerntool.
