35-Piece Rotary Tool Kit Owner’s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.
Thank you very much for choosing an Ironton™ product! For future reference, please complete the owner’s record below: Serial Number/Lot Date Code: ________________________________ Purchase Date: ____________________________________________ Save the receipt, warranty, and this manual. It is important that you read the entire manual to become familiar with this product before you begin using it. This rotary tool kit is designed for certain applications only.
Table of Contents Intended Use .......................................................................................................................................... 4 Packaging Contents .............................................................................................................................. 4 Technical Specifications ...................................................................................................................... 4 Important Safety Information .................
Intended Use The Ironton 35-Piece Rotary Tool Kit has a 1.1 Amp motor with a no-load speed of 10,000 to 32,000 RPM. This variable speed tool cuts, saws, grinds, polishes, and sharpens. It’s designed for use on metal, wood, plastic, glass, ceramic, stone, and more. It includes a 35-piece accessory set. The entire kit is stored in a plastic case. Packaging Contents Rotary Tool Accessory Case Mandrel for Cut-off Disc Mandrel for Cotton Buffer 1 in.
this equipment for a purpose for which it was not intended. Industrial or commercial applications must follow OSHA requirements. ⚠WARNING WORK AREA SAFETY Inspect the work area before each use. Keep work area clean, dry, free of clutter, and well-lit. Cluttered, wet, or dark work areas can result in injury. Using the product in confined work areas may put you dangerously close to cutting tools and rotating parts. Do not use the product where there is a risk of causing a fire or an explosion; e.g.
⚠CAUTION ROTARY TOOL KIT USE AND CARE Do not force the rotary tool. Products are safer and do a better job when used in the manner for which they are designed. Plan your work, and use the correct product for the job. Check for damaged parts before each use. Carefully check that the product will operate properly and perform its intended function. Replace damaged or worn parts immediately. Never operate the product with a damaged part. Do not use a product with a malfunctioning switch.
unit is equipped with an electrical cord that has an equipment grounding conductor and a grounding plug. The plug MUST be plugged into a matching receptacle that is properly installed and grounded in accordance with ALL local codes and ordinances. DO NOT MODIFY THE PROVIDED PLUG. If it will not fit the receptacle, have the proper receptacle installed by a qualified electrician.
Extension Cords ⚠WARNING USE A PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage, resulting in loss of power and cause overheating. Be sure your extension cord is properly wired and in good condition. Always replace a damaged extension cord or have it repaired by a qualified person before using it.
Main Parts of Rotary Tool Kit Reference 1 2 3 4 5 6 7 Subassembly Spring Chuck Securing Ring Spindle Lock Carbon Brush Cap Speed Dial On/Off Switch Manual Stand Before Each Use ⚠WARNING Always remove the plug from the power source before installing. Verify the chuck is tight. Make sure workpiece is properly secured. Always check for damaged or worn out parts before using the rotary tool. Broken parts will affect the rotary tool operation.
Assembling Abrasive Discs and Grinding Stones to Accessory Shaft 1 1. Mount the selected disc onto the accessory shaft 1, as illustrated. Ensure the two washers are correctly placed. 2. Do not over-tighten the screw. Assembling Abrasive Bands to Accessory Shaft 2 1. Slide the abrasive band over the rubber section of the accessory shaft 2. 2. Ensure the abrasive band fits straight and evenly over the rubber portion of the shaft. Assembling Polishing Felts to Accessory Shaft 3 1.
After Each Use ⚠WARNING Store the rotary tool in a dry and clean place. Keep the tool away from children. Maintenance ⚠WARNING Do not use solvents to clean the tool. Inspect the chuck and remove any dirt or debris. Maintain the rotary tool by adopting a program of conscientious repair and maintenance in accordance with the following recommended procedures. It is recommended that the general condition of any tool be examined before it is used. Keep your tool in good repair.
Troubleshooting Use the table below to troubleshoot problems before contacting service personnel or your local dealer. If the problem continues after troubleshooting, call your local dealer for assistance. Failure Possible Cause Corrective Action 1. Check that cord is plugged in. 3. Tool’s thermal reset breaker tripped (if equipped). 2. Check power at outlet. If outlet is unpowered, turn off tool and check circuit breaker.
Parts Diagram Parts List Part Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Part Description Collet nut Collet Base Bearing Rotor Stator Carbon brush Left body Switch Trimming circuit board Lock board Speed control switch Screw Screw Right body Spindle lock button Spring piece Fan Cap body Cord sleeve Cord Plug Page 13 of 16 Quantity 1 1 1 2 1 1 2 1 1 1 1 1 3 6 1 1 1 1 1 1 1 1
Replacement Parts For replacement parts and technical questions, please call Customer Service at 1-800-222-5381. Not all product components are available for replacement. The illustrations provided are a convenient reference to the location and position of parts in the assembly sequence. When ordering parts, the following information will be required: item description, item model number, item serial number/item lot date code, and the replacement part reference number.
Limited Warranty Northern Tool and Equipment Company, Inc. ("We'' or ''Us'') warrants to the original purchaser only (''You'' or ''Your'') that the Ironton product purchased will be free from material defects in both materials and workmanship, normal wear and tear excepted, for a period of one year from date of purchase. The foregoing warranty is valid only if the installation and use of the product is strictly in accordance with product instructions.
Distributed by: Northern Tool & Equipment Company, Inc. Burnsville, Minnesota 55306 www.northerntool.
