IROX-ER + IROX-XL Bedienungsanleitung Mode d¶emploi Modo di uso User manual
TABLE OF CONTENTS 1. INTRODUCTION page 94 2. BASIC OPERATION OF BUTTONS page 96 3. MODE CHANGE OPERATION page 98 4. TIME MODE page 99 5. COMPASS MODE page 102 6. BAROMETER MODE page 106 7. ALTIMETER MODE page 110 8. ALTIMETER DATA MODE page 112 9. CHRONOGRAPH MODE page 113 10. CHRONOGRAPH DATA MODE page 117 11. ALARM MODE page 119 12.
IROX-ER IROX-XL 1 INTRODUCTION This device is a digital product that provides altimeter, barometer, compass, altimeter data, dual time, chronograph, chronograph data and alarm functions. Features: Altimeter – 1 meter (or foot) resolution and with working range from –700 meters (-296 feet) to 9000 meters (29520 feet). – Graphical expression of changes provided. – Unit in meters or feet selectable. – 20 memories with date, time and altitude reading.
Barometer – 1 hPa resolution and with working range from 300 hPa to 1100 hPa. – Graphical expression of changes provided. – Both sea level pressure and absolute pressure can be shown. – Weather forecast. – Temperature displayed in °F or °C selectable. Compass – Electronic compass providing 16 cardinal indications together with bearing in degrees. – Declination correction provided. Time – 2 time modes selectable. – Presents day of the week, day, hours, minutes and seconds (year and month can also be set).
2 BASIC OPERATION OF BUTTONS A: – SWITCH AMONG DISPLAYS – TAKE BEARING – STORE ALTITUDE DATA (PRESS AND HOLD) – FORWARD SELECTION OF ALTITUDE DATA – START/LAP OF CHRONOGRAPH – RETRIEVE DATA IN RUN – TURN ALARM ON AND OFF – FORWARD SETTING (SET OR CALIBRATION) B: – SWITCH BETWEEN NORMAL TIME AND DUAL TIME (PRESS AND HOLD) – SWITCH BETWEEN UNITS OF TEMPERATURE (PRESS AND HOLD) – SWITCH BETWEEN UNITS OF ALTITUDE (PRESS AND HOLD) 96
– REVERSE SELECTION OF ALTITUDE DATA – STOP CHRONOGRAPH – STORE CHRONOGRAPH DATA (PRESS AND HOLD) – SELECT RUN NUMBER – SWITCH BETWEEN ALARM 1 AND ALARM 2 – REVERSE SETTING (SET OR CALIBRATION) C: – MODE CHANGE – DIRECT CHANGE TO TIME MODE (PRESS AND HOLD) – ADVANCE TO NEXT SETTING (SET OR CALIBRATION) D: – EL BACKLIGHT – ENTER SET OR CALIBRATION (PRESS AND HOLD) – CLEAR DATA (PRESS AND HOLD) – EXIT (SET OR CALIBRATION) E: – SWITCH AMONG DISPLAYS – SWITCH BETWEEN DATE AND ALTITUDE READING DISPLAYS – SHOW NU
3 MODE CHANGE OPERATION There are 9 modes: Normal Time, Dual Time, Compass, Barometer, Altimeter, Altimeter Data, Chronograph, Chronograph Data and Alarm. Press C to change from mode to mode, hold down B to switch between Normal Time mode and Dual Time mode as in the following: Hold B NORMAL TIME DUAL TIME C COMPASS C BAROMETER C ALTIMETER C ALTIMETER DATA C CHRONOGRAPH C CHRONOGRAPH DATA C ALARM 98 * At any mode, holding down C will change to Time mode directly.
4 TIME MODE Normal Time indicator PM Indicator Dual Time indicator AM Indicator Hold B Use C to enter Time mode. * Mode prompt “TIME” is displayed first. – There are 2 time modes, Normal Time (indicated by T1) and Dual Time (indicated by T2), and they count up individually with the same second. – There are 3 displays for time. They are Time, Time with Barometer and Time with Weather. – There is an auto-calendar from 2000 to 2049.
To switch among the 3 time displays Use A or E to switch among the 3 displays for time. * “TIME”, “BAROMETER” or “WEATHER” is displayed first. Day of the week Graph of sea level pressure Day Weather indicators A or E A or E Temperature Time Current sea level pressure TIME TIME/BAROMETER Unit indicator of temperature TIME/WEATHER A or E * Graph of sea level pressure is described in BAROMETER MODE.
To set time 1. Hold down D until the hour digits start to flash on the display, which indicates the setting screen. 2. Use A (+) and B (–) to change the setting. Holding down either button scrolls the setting at high speed. 3. Press C to advance to the next setting as in the following: HOUR C C 12/24 H MINUTE C C DAY SECOND C C MONTH YEAR C * When second digits are flashing, press A or B to reset the digits to 00.
5 COMPASS MODE South indicator Bearing Compass mode indicator Cardinal indicator North indicator Hold D CALIBRATION SCREEN Use C to enter Compass mode. * Mode prompt “COMP” is displayed first and bearings will be taken automatically. – Compass mode indicator is shown. – When you take bearings, readings are shown in 16 cardinal indications together with bearing in degrees. * Reading shown indicates the direction that the LCD’s 12 o’clock position is pointing to.
* Declination is the difference between true north and magnetic north. Importance 1. The compass should be calibrated before use. 2. The compass must be kept in a level position when in use. 3. Compass readings are easily affected by disturbing sources of magnetism, so the compass should always be used in the open air. To calibrate the compass 1. Hold down D until “CAL” is shown on the display, which indicates the calibration screen. 2. Rotate the product slowly for 2 complete rotations.
* When E or W is flashing, press A or B to switch between East and West. * You should consult your local organization for information of declination. Declination angles for major cities are listed below for reference only.
6. Press D to end calibration. * If “ERR” indicating error is displayed, calibrate the compass again. * If there is no button operation for 2-3 minutes during calibration or at declination angle setting screen, the display will return to Compass mode automatically. To take bearings 1. Press A, bearings will be taken and shown for about 10 seconds. * If no bearing is being taken, the display shows “----”. 2.
6 BAROMETER MODE Graph of Sea level pressure Weather indicator Current Sea level pressure Barometer mode indicator Unit indicator of pressure Use C to enter Barometer mode. * Mode prompt “BARO” is displayed first. – Barometer mode indicator is shown. – The barometer is of 1 hPa resolution and with working range from 300 hPa to 1100 hPa. – Both sea level pressure and absolute pressure can be shown. – Graph showing the changes in sea level pressure is provided.
– Temperature is of 0.1 degree resolution and with working range from –4°F (–20°C) to 158°F (70°C). And unit in °F or °C selectable. – There are 3 displays for Barometer mode. To switch among the 3 displays for barometer mode Use A or E to switch among the 3 displays for barometer mode.
* It is not possible to get the exact reading from the graph. User can only get the trend of changes from the graph. To switch between °F and °C 1. Use A or E to switch to the barometer display with temperature. 2. Hold down B until the unit indicator (°F or °C) stops flashing to switch temperature between °F and °C. To set sea level pressure reading 1. Hold down D until “SET CURRENT WEATHER” scrolls on the display, which indicates the weather setting screen. * The weather indicators start to flash. 2.
To set current weather 1. Hold down D until “SET CURRENT WEATHER” scrolls on the display, which indicates the weather setting screen. * The weather indicators start to flash. 2. Use A (+) and B (–) to change the setting as in the following: A A A A B B B B 3. Press D to exit the setting screen. * If there is no button operation for 2-3 minutes at setting screen, the display will return to Barometer mode automatically.
7 ALTIMETER MODE Altitude graph Unit indicator of altitude Current Altitude reading Time Altimeter mode indicator Use C to enter Altimeter mode. * Mode prompt “ALTI” is displayed first. – Altimeter mode indicator is shown. – The altimeter is of 1 meter (or foot) resolution and with working range from –700 meters (–2296 feet) to 9000 meters (29520 feet). – Altitude reading in meters or feet selectable. – Graph showing the changes in altitude is provided.
15 minutes while each column represents the relative reading of altitude in that time. * It is not possible to get the exact reading from the graph. User can only get the trend of changes from the graph. To switch between meters and feet Hold down B until the unit indicator (M or Ft) stops flashing to switch altitude reading between meters and feet. To store altitude data Hold down A until “DATA” stops flashing to store the current altitude data. * “STORED” and data number are shown.
8 ALTIMETER DATA MODE Data number Time 3 seconds or E Month-Day Altitude reading Use C to enter Altimeter Data mode. * Mode prompt “ALTI DATA” is displayed first. – Data number, time, date and altitude reading can be retrieved. * Altitude data are shown in 2 different displays. To retrieve the altitude data 1. Use A (+) and B (–) to select the altitude data to be retrieved. 2. Press E to switch between the 2 displays of data.
9 CHRONOGRAPH MODE Lap time indicator Lap time Split time Lap number Split time indicator Use C to enter Chronograph mode. * Mode prompt “CHRO” is displayed first. – The chronograph is of 1/100-second resolution for the first hour and 1second resolution for the rest and with working range up to 24 hours, then the chronograph stops automatically. – For the first hour, the chronograph shows minutes, seconds and 1/100seconds, then it shows hours, minutes and seconds. * Leading zeros will not be shown.
* When you take lap/split times, the display will be frozen to show lap time, split time and lap number for about 6 seconds, then the display will show the current running times automatically. To measure elapsed time 1. Press A to start the chronograph. 2. Press B to stop the chronograph. * You can resume the measurement operation by pressing A. 3. Hold down B until the next run number is shown on the display. * Data of the current run is stored and chronograph is reset to all zeros.
4. Press B when the last runner finishes. * Time measurement is stopped. 5. Hold down B until the next run number is shown on the display. * Data of the current run is stored and chronograph is reset to all zeros. * The finish times for the runners are the split times stored in Chronograph Data mode. To clear times in current run 1. Press B to stop the chronograph. 2. Hold down D until the chronograph shows all zeros. * Times in current run are cleared.
Special function for the model IROX-ER (not for IROX-XL) To show number of unused lap When the chronograph shows all zeros, press E and the number of unused lap (indicated by “FREE”) will be shown for 3 seconds. * Returns to chronograph display automatically after 3 seconds or when any button is pressed.
10 CHRONOGRAPH DATA MODE Run number Lap time indicator Lap time 2 seconds Month-Day Split time indicator Split time ^ Lap number Use C to enter Chronograph Data mode. * Mode prompt “CHRO DATA” is displayed first. – Run number, date, lap/split time of each lap, best lap time and average lap time can be retrieved. – If chronograph is running, chronograph data cannot be cleared. To retrieve the chronograph data 1. Use B to select the run to be retrieved.
Lap number Lap/split time of lap 1 Best lap time Average lap time To clear one particular run 1. Use B to select the run to be cleared. 2. Hold down D until “CLEAR HOLD ALL” is shown on the display, release D and the selected run will be cleared. To clear all runs Hold down D until “----” is shown on the display. * All runs are cleared.
11 ALARM MODE T1 indicator Alarm 1 indicator Alarm time ON/OFF status indicator Chime on indicator Alarm on indicator Use C to enter Alarm mode. * Mode prompt “ALRM” is displayed first. – There are 2 daily alarms and they can be set to refer to Normal Time (indicated by T1) or Dual Time (indicated by T2). – Daily alarm sounds at the same time each day, while it is turned on. – The alarm sounds at the preset time for about 20 seconds, or until you stop it by pressing any button.
* If chime is turned on, confirmation sound will be given whenever a button is pressed. To switch between alarm 1 and alarm 2 Press B to switch between alarm 1 (indicated by AL-1) and alarm 2 (indicated by AL-2). To set alarm time and turn chime on and off 1. Hold down D until the hour digits start to flash on the display, which indicates the setting screen. 2. Use A (+) and B (–) to change the setting. Holding down either button scrolls the setting at high speed. 3.
If chime is turned on, the chime on indicator will be shown after exiting setting screen. 4. Press D to exit the setting screen. * The alarm turns on, which is indicated by ON and the appearance of the alarm on indicator. * If there is no button operation for 2-3 minutes at setting screen, the display will return to Alarm mode automatically. To turn the alarm on and off Press A to turn the alarm on (indicated by ON) and off (indicated by OFF).
12 SERVICE 12.1 RESETTING THE PRODUCT Hold down A, B, C and D simultaneously, all segments will be “on”, then release the buttons and the product will be reset. * After reset, there will not be any measurement of altitude, pressure or temperature until A, C or E is pressed. * After reset, entering Compass mode will change to calibration screen directly. 12.2 BATTERY REPLACEMENT Replace the exhausted battery with a CR2032 cell or equivalent.
Garantieschein Certificat de garantie Certificato di garanzia Warranty Gerät / Modèle / Nome del prodotto / Product Händler (Adresse) / Nom du revendeur (Adresse) / Nome del negoziante (Indirizzo) / Dealer’s name (Adress): Kaufdatum / Date d’achat / Data d’acquisito / Date of purchase www.irox.
