Operation Manual

Issue
Main unit
Radio Controlled
Time signal is not
received
Cannot locate
remote sensor
Place unit by the window and keep it there
overnight
Check batteries
Check location
Press and hold DOWN ( ) button on the
main unit to search for the signal form the
remote sensor
Remote sensor
Symptom Solution
6. CARE INSTRUCTIONS
- Do not expose the device to extreme temperatures or direct sunlight over longer periods.
- Avoid blows and shocks of any kind to the device.
- For cleaning use a dry soft cloth that you have moistened with water and a mild cleaning
agent. Never use volatile substances such as benzene, thinner, cleansing agents in spray
cans etc.
- When the device is not being used store it in a dry area and out of the reach of small
children.
- If the device is activated under extreme coldness it may occur that the display becomes
illegible. As soon as it is returned to a warm environment the device will function
normally.
- Please keep the users manual and other documents delivered with the device stored
carefully so that you can reference them at a later point if necessary.
- Please use only new batteries and never mix old and new batteries.
- Please also remember that old batteries should not be disposed of with household waste
but should be handed in at the designated collection centres.
- Important: With all Irox appliances, all disposal fees in Switzerland (vRG; advance
recycling fee) and in the EU (WEEE) have been paid.
8. TECHNICAL DATA
MAIN UNIT
Indoor Temperature
Operating range: -5°C to +50°C / 23.0°F to 122.0°F
Temperature resolution: 0.1°C / 0.2°F
Power
2 x AAA size 1.5V batteries
Dimensions
70(L) x 130(H) x 14(W) mm
REMOTE SENSOR
Temperature
Operating range with alkaline batteries:
-10°C to + 60°C (14°F to + 140°F)
Temperature resolution: 0.1°C/ 0.2°F
Sampling Interval: 10 seconds
Transmitting Interval: around 47 seconds
RF Transmission Frequency: 433 MHz
RF range: Maximum 100 feet (30 meters)
Temperature transmission cycle: approximately 45 seconds
Table stand
Power
2 x AAA size 1.5V batteries
Dimensions
37.5(L) x 110(H) x 23(W) mm
© Irox Development Technology
5. TROUBLESHOOTING
In case of a malfunction, always check the batteries and replace them in the main unit
and in the sensor(s) with new ones.
Please also check below issues before contacting customer service.
7. SUPPORT
This device is a new development of Irox Development Technology. All information was
made and checked by means of a functioning instrument. It may occur that adjustments
and improvements of the device will take place that due to typographical procedures were
not able to be listed in this manual. Should you notice deviations which make it difficult
for you to operate and use the instrument you may at any time download the latest manual
onto your PC free of charge at www.irox.com (please refer to the version number of the
manual).
SETTING THE TIME ALARMS
1. Press ALARM to select the alarm which you wish to configure.
2. Press and hold ALARM until hour starts flashing in the display
3. Set Alarm Hour:
Press UP () or DOWN () to adjust. Press and hold either button for fast changes.
Press ALARM to confirm your selection.
4. Set Alarm Minutes:
Press UP () or DOWN () to adjust. Press and hold either button for fast changes.
Press ALARM to confirm your selection
5. Upon completion the display will be returned to the alarm selection screen.
Note: Pre-alarm cannot be activated if weekday alarm or single alarm is not enabled.
STOP THE ALARM SOUND
The alarm will sound for 2 minutes with increasing intensity.
To stop it, press ALARM during the Alarm Sound to disable the alarm.
Note: For weekday alarm, pressing ALARM will only disable the alarm for the current
day. The alarm will be activated again the next day (if it falls within Monday to Friday).
If the Alarm is not interrupted by pressing the ALARM key while the sound is active, it
will repeat itself after 8 minutes for 3 times. If you want to stop the alarm in one of the 8
minute periods, you have to do as described in "Activating/Deactivating the Time Alarms".
1817
2019