Instruction Manual

ManualsBrandsIRUN ManualsSports & OutdoorsThe treadmill

ultifunctional Treadmill

Instruction Manual

Please read this manual carefully before using the product and keep it.

Running belt adjustment method

. When running belt lean to the left, adjusting screw on the left 1-2 turns along

the clockwise. Then, test running; If still lean to the left, repeat the above steps

until back to the center.

2. When running belt lean to the right, adjusting screw on the right 1-2 turn

along the clockwise. Then, test running; If still lean to the right, repeat the above

steps until back to the center.

3. When the running belt too tight, it will cause stronger resistance. Please adjust

both sides screws 1-2 turns along the counterclockwise, loosen the belt until

stopping skidding or pausing; When the running belt too loose, please adjust both

sides screws 1-2 turns along the clockwise.

Use the treadmill lubricant

Location is in the middle of the lower surface of the running belt. When add

lubricant, please inject to the center of running board, then put down the belt,

pressing the hole by hands, rotating the belt to apply evenly.

Summary of content (7 pages)

PAGE 1
Running belt adjustment method 1. When running belt lean to the left, adjusting screw on the left 1-2 turns along the clockwise. Then, test running; If still lean to the left, repeat the above steps until back to the center. 2. When running belt lean to the right, adjusting screw on the right 1-2 turns along the clockwise. Then, test running; If still lean to the right, repeat the above steps until back to the center. 3. When the running belt too tight, it will cause stronger resistance.
PAGE 2
Thank you very much for purchasing this product, to be able to use the product, be sure to read this manual. Treadmill Common Error Messages Prompt Description Treadmill main parameters When communication line is Please connect again or blocked between Electronic change communication line 1. Running Area: 980*390mm 2. Max User’s Weight: 100KG 3. Set up Size: (L*W*H)1300*655*1230mm 4. Folding Size: (L*W*H)520*655*1270mm 5. Motor : 0.5hp 6. Speed: 1-12.8 7.
PAGE 3
Packing Details 9. Each numerical display range： Initial Set initial value Setting range Display Range Time(min:sec) 0:00 45:00 1:00-45:00 0:00~45.00 Speed(km/h) 0.0 N/A N/A 1-12.8 Distance(km) 0.0 1.0 1.0-99.0 0.0-99.
PAGE 4
B. Countdown mode Assembly steps First step: Base assembly With screw E(4 pcs), washer C(4 pcs) and cap nut F(4 pcs) to carry round bracket fixed to the base. 1. Enter time countdown mode: In the initial standby mode press Kin selection time countdown mode, where the time window 30:00 minutes and flashing speed by +/- keys set the desired run time, set the range of 8: 00-99 : 00 minutes, press the start button to enter the running time countdown mode. 2.
PAGE 5
Third step: Display structure assembly 3. LCD display instruction LCD(94774) shows: Speed, Time, Distance, Calories. First electronic watch frame folded direction of the arrow, and then screw A(2 pcs), washer C(2 pcs) electronic table frame fixed on the column. 4. Button function  Function button: Speed Shortcuts 4 (2, 4, 6, 8) “Start” button “Stop” button “Program” button “Mode” button “Speed+” button “Speed-” button 5.
PAGE 6
Folding and unfolding No lift electronic watches Operating Instructions When folded, the first M FIG release knob subject, raised his hand to the Folding CAUTION CAUTION back of the treadmill to the vertical Read t he owner ' s manual car efully befor e us ing t he pr oduct . To avoid injur y,stand on the side r ails befor e star ting the unit. Remov e t he s afet y key when t he unit is not in us e. Keep childr en away fr om the tr eadmill during oper ation.
PAGE 7
FCC Warning This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any inte rference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.