Thank you for using the product from SHENZHEN ISD TECHNOLOGY CO.,LTD This product is specifically designed for RC, not appliance in other areas. We strongly recommend you read our user’ s guide before using BG-8S. ISDT accepts no liability for damage, injury or any legal responsibility incurred directly or indirectly from the use of this product. ISDT reserves the right to update the design, appearance, function and usage requirement without notifying.
Working voltage : 5.0V - 36V Input voltage 1s : 0.8V - 15V Input voltage 2-8S : 0.8V - 4.8V Battery cells : 1-8s Voltage measurement accuracy : ±0.005V @ 4.2V Balancing cells accuracy : < 0.005V Support USB charging : QC3.0, BC1.2, Maximum output 12V/2A Support smart battery : Charging and discharging setting, read battery info and usage history. Dimension : 80 X 55 X 19 mm Weight : 59 g 8S 7S 6S 5S 4S 3S 2S 1S This product is suitable for the lithium battery which has the XH 2.
25.24V 8mV 100% 33℃ 22.93V BattGO 10mV 2017-07-28 45% LiPo-6S 4000 mAh 2C 25C 10 0 0 0 01 34℃ 3.81V 3.82V 3.82V 3.82V 3.82V 3.82V -.--V -.--V 02 In this mode, BG-8S can read smart battery info.
XT60i Input voltage Cells voltage difference Remaining capacity Battery temperature 25.24V 8mV 100% 33℃ BattGO Battery brand LiPo-6S Battery type 2017-07-28 4000 mAh Production date Battery capacity Max Charging C 2C 25C Max discharging C Battery circulation 10 0 Over temperature 0 0 Battery over discharging Battery over charging 22.93V 10mV 45% 34℃ 25.24V 0mV 3.81V 3.82V 3.82V 3.82V 3.82V 3.82V -.--V -.
23.19V 14mV Cells Voltage 3.855V 3.869V 3.868V 3.865V 3.861V 3.868V -.---V -.---V When battery connecting to balance port, BG-8S will show total battery voltage, max voltage difference between each cell and each cell voltage PS: When only balance port is connected, short press menu twice, BattGo can initiate cell balancing task. Short press menu button to see system function menu below: Function Language Backlinght Volume System Information Receiver Tester English Middle High ... ...
Language Support up to 7 languages Backlinght Back light adjustment, back light will automatically turn off in 2 minutes if no operation( In balancing 20 seconds) Volume Support high, middle, low and 0 volume. Alarm sound can not be turned off. System Information Show firmware version Receiver Tester Support multiple prototype testing, PWM\ S.
S.Bus -2 0 97 0 -46 97 128 19 128 128 0 0 0 0 0 0 RC control signal PWM protocol analysis, connect to servo receiver signal output, BG-8S will detect PWM output period and pulse width PWM 5.10V 38% 66Hz 1683us S.Bus protocol analysis, support up to 18 channels servo control data analysis, servo receiver failure protection testing.
When XT60i is connected to the battery, BG-8S could perform USB charging function. In USB charging, after 2 minutes without operation. display will turn off, and light up breath light to purple. If current is more than 3A or power is more than 26W it will turn off USB charging. If temperature is more than 60 °, it will stop charging until temperature is lower than warning level. It will recharge automatically. Battery capacity and BattGo mark would appear only smart battery is connected.
When balance port is connected, user can initiate cells balancing task. During task, display will turn off, breath light will turn on within 20s, if no operation is detected。 battery capacity percentage, temperature BattGo mark will only show when smart battery is connected, 23.07V 9mV 68% 33℃ 00:00:32 Cells Voltage 3.846V 3.844V 3.842V 3.851V 3.843V 3.846V -.---V -.---V In balancing cells would show as yellow, and breath light is green during operation. 23.
This battery checker is suitable for :LiHv (1-8S) / LiPo (1-8S) / LiFe(1-8S) / Lilon (1-8S) / NiMH/Cd(1-10S); this battery checker is suitable for the connection with balance port of battery, While connect to the battery checker, negative electrode of the balance port must start from “BAT“ . Reverse protection circuit is inside the BG-8S, no damage will cause to BG-8S while connect reversely. BG-8S is designed for RC areas, please don’ t use this on other purpose.
Shenzhen ISD Technology CO.,LTD Address:5th Fl., Bldg. 9, Mabian Industrial Zone, Yangtian Rd., Block 72, Xin'An Street,Bao'An District, Shenzhen, PRC Changes in specifications and data will not be further noticed. Email:hi@isdt.
