P20 双通道 智能充电器 用户手册 DC IN 8S CHARGER P20 SMART 2S 2S CH1 CH2 8S
感谢您购买ISDT P20 智能平衡充电器。 欢迎您登陆艾斯特官方网站www.isdt.
接口 / 按键 CH1电池 输出口 CH1 平衡口 显示屏 通道选择键 及方向键 CH2 平衡口 CH2电池 输出口 CHARGER P20 SMART USB-C升级口 风扇散热口 按键操作说明（待机界面下） CH1菜单键：短按进入CH1详细参数界面，长按进入CH1任务设置菜单。 CH2菜单键：短按进入CH2详细参数界面，长按进入CH2任务设置菜单。 同时长按CH1和CH2菜单键：进入高级设置菜单。 电源输入口
如何确定充电电流 在充电前必须先了解清楚所用电池允许的最大充电电流，使用过大的电流对电池充电会对电池的寿命造成 影响甚至损坏，过大的电流也会造成充电过程中电池发热甚至爆炸。电池充放电能力一般以C数来标识， 充电C数乘以电池容量就是电池所支持的最大充电电流，例如1000mAh的电池，标识充电能力是5C，那么 最大充电电流为：1000×5=5000mA=5A，也就是最大支持5A充电。对于锂电池而言，如果无法确定电池 充电C数，为了安全起见请将充电电流设定在不大于1C的值。 充电C数与充电时间的参考关系：充电时间≧60分钟/充电C数（例如使用1C充电，充电完成时间大约需要 60~70分钟），由于电池转换能效的差异，此时间有可能会有所延长。 充电器预设电池类型及任务参数 支持 串数 最大充 电电流 1.10V 1~16S 20.0A 1.90V 1~12S 20.0A 3.30V 2.90V 1-8S 20.0A 4.10V 3.70V 3.20V 1~8S 20.0A 3.70V 4.20V 3.80V 3.30V 1~8S 20.0A 3.80V 4.
充电 对于锂电池，强烈建议连接平衡端口均衡充电，以确保充电器能准确监测每个电池的电压，并对不一致的电 芯进行平衡操作。当使用非平衡模式(不连接电池平衡口)充电时，充电器在开始任务前会有相应的报警提示。 电流设定范围为0.2~20A。当连接BattGo电池时，电池类型、串数以及充电电流根据BattGo信息自动设定。 放电 电流设定范围为0.2~1.5A。当连接BattGo电池时，电池类型、串数以及放电电流根据BattGo信息自动设定。 存储 电流设定范围为0.2~20A。当连接BattGo电池时，电池类型、串数以及存储电流根据BattGo信息自动设定。 销毁电池 连接需要报废的电池，在任务选项中选择报废功能，可将电池放电至0V。 电流设定范围为0.2~1.
双通道任务选择 选择该项，充电器将以相同参数对两个通道下的电池同时进行充电/放电/存储。将充电器接通电源并接上 电池，在高级设置菜单中选择该项进行双通道任务参数设置。 直流电源 选择该项，充电器的CH1将成为一个直流电源。输出电压为2~30V可调，电流为1.0~5.
系统自检 在移除CH1及CH2所有电池连接后，选择该项进行系统自检操作。 校准 选择该项，可校准充电器的输入电压，输出电压和平衡口电压。 www.isdt.co *本产品所有图片、声明及文字资料仅供参考，实际信息请参考官方网站 www.isdt.
P20 DUAL CHANNEL SMART CHARGER USER GUIDE DC IN 8S CHARGER P20 SMART 2S 2S CH1 CH2 8S
Thanks for purchasing the ISDT P20 Smart Charger. Please visit: www.isdt.co for more details on the functions of this smart charger, as well as purchase various accessories. Functions of products will be kept on upgrading, the manual in your hand may be different from the actual operation, please refer to the actual functions. Warnings and Safety Tips For your safety and a better user experience, please read this manual and follow the instruction before using the new charger.
Port / Button CH1 Power CH1 Output Balance Port Display Screen Channel Selection Button & Direction Button CH2 CH2 Power Balance Port Output CHARGER P20 SMART USB-C Upgrading Port Power Input Fan Vent Key operation instructions (under standby interface) CH1 Channel selection button: Short press to enter the CH1 detailed parameter interface, Long press to enter the CH1 task setting menu.
How to Confirm Charging Current Make sure to know the maximum charging current of the battery before charging, never use excessive current to charge to damage your battery, which will result in over heat even explosion during the charging process. The charging and discharging capacity of battery is usually marked with C value. Multiplying the charging C value and battery capacity equals to the maximum charging current supported by the battery.
Charge Balancing port is strongly recommended when charging lipo battery, which can make sure to monitor voltage on each cell battery and balance it when charging. Warning beeper will yell before start charging lipo if in non-balance mode (no connecting with balance port). Current setting range: 0.2~20A. The battery type, cell count and charging current are auto set accordingly when connecting with BattGo battery. Discharge Current setting range: 0.2~1.5A.
Paralled task Select this setting, it could output Max Power to one battery. Find a power splitter or 1/2 power cord, one end connect with the battery, and the other two ends connect with the battery output port. The battery balance port could connect with any of the charger's balance port. Connect the charger with the power supply and power on, and connect your battery as required, select this setting on the advanced setting menu to set the task parameters.
Theme Select this option to set the background color to bright/dark. Continuous trickle After charging is complete, choose whether to continue trickle charging. The trickle charge function is enabled to maintain the lithium battery voltage in a fully charged state, this function is enabled by default. Split screen There are 3 options of 60 seconds,30 seconds and OFF for automatic split screen setting.
