AC/DC双通道智能充电器 用户手册
感谢您购买ISDT K1 智能平衡充电器。 欢迎您登陆艾斯特官方网站www.isdt.
接口 / 按键 AC电源 输入口 通道 选择键 风扇 散热口 DC电源 输入口 按键操作说明(待机界面下) CH1选择键:短按进入CH1详细参数界面,长按进入CH1任务设置菜单。 CH2选择键:短按进入CH2详细参数界面,长按进入CH2任务设置菜单。 同时长按CH1和CH2确认键:进入高级设置菜单。 CH1 平衡口 USB-C 升级口 CH1电池 输出口 方向键 CH2电池 输出口 CH2 平衡口 显示屏
充电器预设电池类型及任务参数 支持 串数 最大充 电电流 1.40V 1~16S 10.0A 2.40V 1~10S 10.0A 3.20V 3.65V 1~6S 10.0A Lilon 3.60V 4.10V 1~6S 10.0A LiPo 3.70V 4.20V 1~6S 10.0A LiHv 3.80V 4.35V 1~6S 10.0A ULiHv 3.90V 4.45V 1~6S 10.0A 额定 电压 满充 电压 NiCd/MH 1.20V Pb 2.
工作参数显示 工作中在方向键上可以切换屏幕下半部分的信息显示内容,信息内容依次为:各电芯电压、各电芯内阻、工作参数。 其中电芯电压及内阻仅在平衡充电模式下才会显示。 高级设定 待机界面下,同时长按左右两边通道选择键进入高级设置菜单,菜单项如下: 双通道任务选择 选择该项,充电器将以相同参数对两个通道下的电池同时进行充电。 将充电器接通电源并接上电池, 在高级设置菜单中选择该项进行双通道任务参数设置。 直流电源 选择该项,充电器的CH1将成为一个直流电源。 输出电压为5~24V可调,电流为0.2~5.
自动分屏 自动分屏设置有60秒、30秒及关闭三个选项。 可选择在设定时间内,主界面显示由单通道参数界面自动切换至双通道(分屏)参数界面。亦可选择“关”,将自动分屏功能关闭。 系统自检 在移除CH1及CH2所有电池连接后,选择该项进行系统自检操作。 校准 该项可以校准充电器的输入电压,输出电压和平衡口电压。 www.isdt.co *本产品所有图片、声明及文字资料仅供参考,实际信息请参考官方网站 www.isdt.
AC/DC DUAL CHANNEL SMART CHARGER USER GUIDE
Thanks for purchasing the ISDT K1 Smart Charger. Please visit: www.isdt.co for more details on the functions of this smart charger, as well as purchase various accessories. Functions of products will be kept on upgrading, the manual in your hand may be different from the actual operation, please refer to the actual functions. Warnings and Safety Tips For your safety and a better user experience, please read this manual and follow the instruction before using the new charger.
Port / Keys AC Power Input Channel Selection Key Fan Vent DC Power Input CH1 Balance Port USB-C Upgrading Port CH1 Power Output Arrow Keys CH2 Power Output Display Screen CH2 Balance Port Key operation instructions (under standby interface) CH1 Selection key: Short press to enter the CH1 detailed parameter interface, long press to enter the CH1 task setting menu. CH2 Selection key: Short press to enter the CH2 detailed parameter interface, long press to enter the CH2 task setting menu.
Preset Battery Type of Charger and Task Parameters Supported Cell Count Max. Charging Current 1.40V 1~16S 10.0A 2.40V 1~10S 10.0A 3.20V 3.65V 1~6S 10.0A Lilon 3.60V 4.10V 1~6S 10.0A LiPo 3.70V 4.20V 1~6S 10.0A LiHv 3.80V 4.35V 1~6S 10.0A ULiHv 3.90V 4.45V 1~6S 10.0A Rated Voltage Full Charge Voltage NiCd/MH 1.20V Pb 2.
Charge Balancing port is strongly recommended when charging lipo battery, which can make sure to monitor voltage on each cell battery and balance it when charging. Warning beeper will yell before start charging lipo if in non-balance mode(no connecting with balance port). Current setting range: 0.2~10.0A Charging Screen Press the direction button to switch the information displayed in the lower half of the screen, as cell voltage, cell internal resistance, working parameter.
System Setting Menu Under the advanced setting menu, select the system setting into the system setting menu as follows: Min. input voltage protection: 10~24V all tasks in operation will be stopped at once and hint warning of low voltage, when the input voltage is lower than the input voltage as set up. It will protect the battery from being discharged when using battery pack as power supply. Max.