Warnings and Safety Tips The following safety tips are essentially important. Please strictly follow the manual’s instructions in operation to guarantee safety. Improper operation or incorrect working parameter settings may cause damages to the charger and battery and/or result to a fire. Do not use the charger in an unattended manner; in case of any functional abnormity, please stop using it and refer to the manual.
Product Parameters and Characteristics 2 1 Guide For the Connection 3 of Balanced Port 7 4 6 5 1. 2.4”IPS Display 5. Speed Shuttle key 3. Update Port 7. Battery Port 2. Power Input 4. Opto- sensor 6.
Product Parameters and Characteristics 80MM 80MM Specifications: 33.
Default Battery Type of Charger and Task Parameters NiCd/NiMH Pb LiFe Lilon LiPo LiHv Rated Voltage 1.20V 2.00V 3.20V 3.60V 3.70V 3.80V Full Charge Voltage 1.40V 2.46V 3.65V 4.10V 4.20V 4.35V Storage Voltage Not supported Not supported 3.30V 3.70V 3.80V 3.85V Discharge Voltage 1.10V 1.90V 2.90V 3.20V 3.30V 3.40V Pre-charge Voltage 0.90V 1.80V 2.60V 2.90V 3.00V 3.
How to Confirm Charging Current It is very important to know the maximum charging current of the battery as excessive current could influence the life span of battery and/or cause damages. In addition, excessive current can cause heating and/or explosion of the battery during the charging process. The charging and discharging capacity of battery is usually marked with C value. Multiplying the charging C value and battery capacity equals to the maximum charging current supported by the battery.
Task Setting Connect the charger to the power supply and wait for the system to complete the self testing. Connect the battery to the charger under standby interface, and short press the shuttle key to make the task setting menu to pop up. The items in the menu are as follows: Select task contents: Charge, Discharge, Storage Select battery types End-voltage slight adjustment, range ±0.
Task Setting The working mode of the charger is series charging; you must therefore connect it to the output line of the battery while charging. For a lithium battery, it is highly suggested that the balanced interface should be connected to carry out balanced charging to accurately monitor the voltage of each cell and balance the ones with bad consistency.
Task Setting Since the way of internal resistance measurement varies, it cannot be realized to measure the absolute value as professional internal resistance tester does. Therefore, the internal resistance value can only be referred to when conducting horizontal comparisons, such as judging the consistency of the cells’ performance or making comparisons of the performance of different cells.
Working Parameters Display Device Name Task operation time Battery percentage Present current Capacity charged Battery type – string number Current task status Cell voltage 00:17:18 Q6 Pro 8.0 A Battgo smart battery input information Smart battery brand Smart battery types&series Smart battery capacity 97% 1.
Working Parameters Display 00:14:35 0.1 A Q6 Pro 1.26 Ah Lipo-6S Fast Charg Done 3.6mΩ 3.5mΩ 3.5mΩ 3.5mΩ 3.5mΩ 3.5mΩ 00:26:39 0.1 A Q6 Pro 1.76 Ah Lipo-6S Charg Done 27.0V/4W 261Wh 25.
System Setting BattGO Max.input power Min.input voltage Long press the shuttle key in standby interface to make the system default menu pop up, and the items are as follows: Backlight Volume Completion Tone Language Firmware Sharing System Information System Self-checking Back ... 330W 7.0V High High Repeat English ... ... ...
BattGO Setting Auto Storage 240h Storage Voltage 3.80V Charge Voltage 4.20V Charge Current Exception Record Back 2.6A ... The battgo settings as below will be showed if connect the battgo smart battery: When default set allow auto storage mode, the time could be set between 12h-240h set the storage voltage slightly, adjustable range of voltages is -0.20V change charge current slightly, adjustable range of currents is between 0.
Error in power on self-testing: the charger can automatically carry out a self-testing when connected to a power supply. A self-testing error warning sound should be heard when the charger is connected to the battery; power on after removing the battery for 5 minutes.
This smart charger conforms to relevant CE command and relevant commands in B: 2010, CHAPTER 15, FCC Testing standards Result EN 55014-1:2006+ A1:2009+A2:2011 YES EN 55014-2:1997+ A1:2001+A2:2008 YES For electronic products with this marking in their manuals, please separately dispose them with family garbage. When a charger gets spoilt and cannot be used anymore, please take it to a nearby garbage station or recycle center.
TM Shenzhen ISD Technology CO.,LTD Address:5th Fl., Bldg. 9, Mabian Industrial Zone, Yangtian Rd., Block 72, Xin'An Street,Bao'An District, Shenzhen, PRC Changes in specifications and data will not be further noticed. Email:hi@isdt.
