T series is ISDT produced high-performance smart balance charger. With T8 \ T6 \ T6 Lite Please visit : www.isdt.co for more details on the functions of this smart charger, as well as purchase various accessories. Functions of products will be kept on upgrading, the manual in your hand may be different from the actual operation; please refer to the actual functions.
Warnings and Safety Tips The following safety tips are essentially important. Please strictly follow the manual’s instructions in operation to guarantee safety. Improper operation or incorrect working parameter settings may cause damages to the charger and battery and/or result to a fire. Do not use the charger in an unattended manner; in case of any functional abnormity, please stop using it and refer to the manual.
Product Parameters and Characteristics 1 9 8 2 3 7 4 6 5 100MM 120MM 58MM
Product Parameters and Characteristics Input Voltage Maximum input current Output voltage Support smart battery DC 8-32V DC 8-32V DC 12-40V 30A 35A 35A 0-30V 0-30V 0-37V Output support Input/Output support Input/Output support Charge Current 0.1-25.0A 0.1-30.0A 0.1-30.0A Discharge Current 0.1-5.0A 0.1-5.0A 0.1-5.0A Max Charge Capacity 600W 780W 1000W Max Discharge Capacity 20W 20W 20W 1.5A/cell 1.5A/cell 2.2A/cell Balance Cells 2-6S 2-6S 2-8S USB Output 5V/2.1A 5V/2.
Default Battery Type of Charger and Task Parameters NiCd/NiMH Pd LiFe Lilon LiPo LiHv Rated Voltage 1.20V 2.00V 3.20V 3.60V 3.70V 3.80V Full Charge Voltage 1.40V 2.46V 3.65V 4.10V 4.20V 4.35V Storage Voltage Not supported Not supported 3.30V 3.70V 3.80V 3.85V Discharge Voltage 1.10V 1.90V 2.90V 3.20V 3.30V 3.40V Pre-charge Voltage 0.90V 1.80V 2.60V 2.90V 3.00V 3.
How to Confirm Charging Current It is very important to know the maximum charging current of the battery as excessive current could influence the life span of battery and/or cause damages. In addition, excessive current can cause heating and/or explosion of the battery during the charging process. The charging and discharging capacity of battery is usually marked with C value. Multiplying the charging C value and battery capacity equals to the maximum charging current supported by the battery.
Task Setting Task Settings Task Settings LiPo-8S 4.20V Battery Type LiPo Task Charge Cell Count 8S 30.0A Current Cells Voltage 3.3V/Cell Input Limit Start Currnet Task Back Input Limit 4.20V 30.0A Charge Back Input/Output BattGo smart battery Input/Output normal battery Connect PSU to charger, wait until charger is in standby then connect your battery to charger.
Task Setting Input/Output normal battery Battery Type Battery type selection Cells Voltage End voltage slight adjustment, range ±0.05v Cell Count Currnet Task Input Limit Back Battery cell selection auto detection if balance port is connected Current selection, charge / store (T6 Lite) 0.1-25.0A (T6 T8) 0.1- 30.0A, discharge 0.1- 5.0A Select the task contents Charge / Discharge // Storage Start task back T series charger will charge battery in series, make sure output port is connected.
Task Setting Over-discharging battery reactivate and repair function Over-discharging battery reactivate and repair function After charging task initiates, if battery voltage is lower than pre-charging voltage, charger will charge battery at 0.1A to reactivate and repair. After battery voltage is higher than pre-charging voltage, charger will charge battery as setting. This procedure can protect over-discharging battery then reactivate and repair Resistance detection Charger support resistance detection.
Working Parameters Display Charging current battery type&voltage Charged energy Operation time Task condition 25.3 A LiPo-8S 33.42V 4.96Ah 00:12:18 Charging Connected battery support BattGo Cells Voltage 4.17V 4.18V 4.18V 4.18V 4.18V 4.18V 4.17V 4.18V Cells Impedance 2.5mΩ 2.6mΩ 2.6mΩ 2.6mΩ 2.9mΩ 2.6mΩ 2.6mΩ 2.
Working Parameters Display 25.3 A LiPo-8S 33.42V 4.96Ah 00:12:18 Charging BattGo smart battery input info Cells Voltage 4.17V 4.18V 4.18V 4.18V 4.18V 4.18V 4.17V 4.
Working Parameters Display 1.3 A Cells Impedance LiPo-6S 25.19V Fast charging complete 2.96Ah 00:13:18 Fast Charge Done 0.0 A Cells Voltage 4.20V 4.20V 4.20V 4.20V 4.20V 4.20V 4.20V 4.20V LiPo-8S 33.60V 1.5Ah 00:15:18 Charge Done Precise Balance Charging -1.0 A LiPo-5S 20.0V -65mAh 00:04:54 Discharging Working Info 15.1V/1W 3.95~3.96V -20W 59℃ 1pcs 5pcs Discharge state 0.8 LiPo-8S 30.5V 8.5mΩ 8.6mΩ 8.6mΩ 8.6mΩ 8.9mΩ 8.6mΩ -.-mΩ -.-mΩ A 96mAh 00:03:36 Storage Charging Cells Voltage 3.
System Default Function Language Firmware Sharing System Information System self-checking Volume When using smart battery as input Input connecting to BattGo Output connecting to BattGo English ... ... ... High Completion Tone Repeat Max.input power 1000W Backlinght Min.input voltage BattGO BattGO Back High 12.0V ... ... Max input power: when PSU could not meet max operation power(1000w), to protect PSU and charger working stability, user should adjust this value based on PSU.
System Default In standby, long press to enter system setting. Language Firmware Sharing System Information System self-checking Volume Completion Tone Backlinght Support up to 7 languages By using ISDT sclinker, user can share firmware to same model. Show firmware version To check hardware is working properly Beeper volume adjustment, high, middle low and off Single time or multiple time(1 time/ min) Back light adjustment, high, middle , low and auto Max.
System Default Auto Storage Off Storage Voltage 3.80V Charge Voltage 4.20V Charge Current Exception Record 3.4A Back ... Both input and output connecting to BattGo battery, system menu shows as below: Auto Storage When smart battery supports auto discharging, you can select after how many hours battery starts auto discharging. Storage Voltage Slight adjustment for storage voltage, from 0 to -0.
Troubleshoot Error in power on self-testing: the charger can automatically carry out a self-testing when connected to a power supply. A self-testing error warning sound should be heard when the charger is connected to the battery; power on after removing the battery for 5 minutes.
Product Qualification Declaration This smart charger conforms to relevant EC command and relevant commands in B: 2010, CHAPTER 15, FCC Testing standards Result EN 55014-1:2006+ A1:2009+A2:2011 YES EN 55014-2:1997+ A1:2001+A2:2008 YES For electronic products with this marking in their manuals, please separately dispose them with family garbage. When a charger gets spoilt and cannot be used anymore, please take it to a nearby garbage station or recycle center.
TM Shenzhen ISD Technology CO.,LTD Address:5th Fl., Bldg. 9, Mabian Industrial Zone, Yangtian Rd., Block 72, Xin'An Street,Bao'An District, Shenzhen, PRC Changes in specifications and data will not be further noticed. Email:hi@isdt.
