Owner's Manual
A.
Locate
factory Power antenna
wire
in
radio's wiring
harness.
This
wire
will
be
in
Pin
location #18 (See
Diagram)
B.
Cut
this
wire about 2 inches
from
the back of
the
radio.
C.
Carefully remove about%
an
inch
of insulation
from
the wire
on
the VEHICLE'S
side.
(Not the
wire
connecting into
the
radio)
D.
Locate the accessory
wire
Pin
location#
20
(See
diagram)
E.
About 2 inches away from the radio carefully remove
about
Y2
an
inch of insulation
from
this
accessory
wire.
Powor
MtotnnaVWe
F. Connect the vehicle's
side
of the Power antenna wire( stripped) to the accessory
wire.
(solder this connection to ensure the best connection possible)
G.
Insulate this new connection
on
the
Accessory
wire
to
prevent
an
electrical short
7.
If connecting the Satellite
Radi
o tuner (
SCC1
sold
separartely}, make the folllowing
connections before connecting the
PXAMG
to the
vehicle.
Plug
the black
end
of the
3 foot PXAMGSR (8-Pin mini-din
to
8-Pin
mini-din;
sold
seperately)
into
the second
port (closest to the dipswitches)
on
the Media
GateWay.
If
you
are installing the
Satellite Radio Tuner with the HDRT, connect the PXAMGSR cable to the port
farthest
from
the dipswitches. Connect the gray
end
of this cable into the Satellite
Radio
tuner.
8.
If connecting the
ISBT21
(sold separartely), make the folllowing
connections before connecting the
PXAMG
to the vehichle.
Plug
the 3 foot
ISBT21
Cable
(8-Pin
mini-din to
8-Pin
mini-din) cable into
the
first port (farthest
from
the dipswitches)
on
the
Media
GateWay.
Connect the other
end
of this cable
into
the
ISBT2
1.
Connect
the
micro
phone
cable into the 3.5
mm
connecti
on
on
the
ISBT21
.
9.
Plug
in the ma
le
conne
ctors
on
the
PGHTY1
harness into the 12-pin port
on
the
ba
ck of the radio. Next, connect the
fa
cto
ry
12-pin harness (if present) into the
fema
le
conne
ctor
on
the
PGHTY1
harness.
Be
sure
to
make
a
firm
connection but
do
not force it.
Plug
the Black micro-fit 24-pin connector
on
the
PGHTY1
harness
into the PXAMG
Media
GateWay
box.
10
.
To
complete the installation secure the Media
GateWay
(PXAMG)
and
HD
Radio
tuner (
HDRT
if equipped) into the cavity
in
the dash behind the
radio.
Be sure that
the
cables
and interface modules are not near moving
parts
or sharp metal
edges
as they may damage the cables.
To
prevent
rattling
noises inside the dash, use zip
ties,
tape, or other fasteners to mount
the
interfaces
securely.
11
.
With
all
connections made, reconnect
the
vehicle's battery, insert the key into the
ignition
,
and
tum the vehicle
on
. Check for proper operation of the Media GateWay
and
HD
Radio tuner before reinstalling the facto
ry
dash panels.
12
.
Note
: The first time
you
access the GateWay, your
radio
may display "DEV I NIT'
while the
de
v
ice
is
initializing. If
this
is
displayed, please wait
one
minute then
cycle the ignition off
and
on
. Then access
SAT
mode
again
to
begin
normal
GateWay
operation.
6