Instruction Manual PROFESSIONAL INSTALLATION STRONGLY ADVISED IMPORTANT NOTE iPad Firmware MUST be updated BEFORE any other step is taken. Otherwise, the iPod will not operate properly. See page 1 for further derails. Peripheral Electronics®, a division of AMP of America ™ 13160 56th Court Clear water, Florida 33760 866-788-4237 in the US or 727-572-9255 ext 262 for international calls support@peripheralelectronics com ©2006 AAMP™ of Florida, Inc.
Table of Contents Pages CHAPTER 1-Getting Started 1.1 Introduction 1 1.2 Precautions 1 1.3 Configuration & Ha messes 2 1.4 Compatibility Notes 2-3 1.5 Application Guide 4-9 1.6 Programming the Podgorica 10 CHAPTER 2-General Installation 2.1 Installation Location 11 2.2 Pr-installation Checklist 1 2.3 Wiring Connections 1-12 2.4 Installation at Changer Location 12-13 2.4 Installation at Radio 13 CHAPTER 3 -Operation 3.1 Operation 14 3.2 Troubleshooting 15 3.3 Warranty 16 3.4 Naming 16 3.
Chapter 1 Getting Started 1.1 Introduction Thank you for purchasing Peripheral Electronics® Podgorica interface The tripodal is designed to provide endless hours of listening pleasure through most vehicles! factory radios.
Podgorica interface Backing cable Vehicle specific harness 1.3 Configuration and Harness Selection This section will instruct you on-how to properly identify and/or confirm: the proper in= terrace dip-switch configuration and vehicle specific shames selection. On the follow: ing pages you will find our vehicle application guide: This guide will inform you of the proper dip-switch configuration and vehicle specific harness for your particular vehicle Depending on the type of polarize kit vou purchased.
1.4.5 DODGE. See Chrysler 1.4.4 1.4.6 EAGLE. See Chrysler 1.44 1.4.7 Ford The Podgorica is not compatible with factory radios with builtin 6-disc CD changers. 14.8 Seeming Chevrolet 1.4.3 1.4.9 Honda Starting in 2003 Honda introduced a new series of radios that use different software that is currently incompatible with the Podgorica. ih 2005 all Honda radios use this software raking them incompatible. 1.4.10 HUMMER. See Chevrolet 1.4.3 1.4.11 JEEP: See Chrysler 1.4.4 1.4.
1.6 Programming the Podgorica Now that you have identified the correct harness and dip-switch configuration using the application guide, it Is now time to program the interface. To program the interface, set the dip-switches located on the side of the interface {see Fig. 1 below) to the configuration listed for your vehicle in the Application guide. Switches are in their default setting of "off! in the up position and are turned “on” when switched down. Refer to the chart on the bottom of this page.
Chapter 2 General Installation 2.1 Installation Location Most installations will require you to remove the factory radio in order to plug in the Vehicle specific shames, Some vehicles may require you ta connect the interface to a factory pre: run CD changer cable. The location of these CD changer cables will vary by vehicle. Some common locations of these cables are in the trunk. behind the glove box and in or under a center console.
Make these connections only after verifying the proper circuit an your radio harness with a voltmeter With the key OFF and the negative test lead of the voltmeter firmly touching a bare metal chassis part of your car, begin probing the wires in the main radio: harness with the positive test sad. Teri constant 12V+ circuit should read a continuous 12 volts or higher. Once you've identified the constant 12V+ circuit. strip back about 1/8" of the insulation.
4: Decide on a convenient location to mount your iPod: 5. Rut the white docking cable from the interface to the desired mounting location. Use caution to note: pinch. or crimp the cable during this step. Avoid moving parts, vehicle wiring harnesses and areas of excessive heathen routing the cable. 6. Secure the interface in the vehicle using double sided tape; Velcro or wire ties. Make sure to check for proper clearance and avoid moving parts.
Chapter 3 Operation 3.1 Operation SELECTING THE IPOD To select the Pod from the radio. press the button that would normally activate the factory CD changer This bunion varies by vehicle manufacturers. In some applications {using con fig #8 the (Podgorica is accessed like an XM receiver In these cases you will press the appropriate activation bunion, Some radio models require pressing the "Seek >” button once, after pressing the CD button.
3.2 Trouble Shooting Symptom Cause Remedy No Power Blown fiche in vehicle fuse Replace fuse with same block: amp rating. If the fuse blows again, call tech support No Power Bad connection Check cable and wiring connection. Alternator noise is heard {Changes with Engine REM) Improper wiring creates a ground loop install a Ground oop Isolate: tor or seek professional service from a local car idiomatic shop. You can hear music from the iPod but you cant con: troll it from the radio.
3.3 Warranty One Year Limited Warranty The quality controls Used in the manufacture of this product will ensure your satisfaction. This warranty applies only fo the original purchaser of this product from an authorized Peripheral Electronics dealer, This warranty covers any supplied or manufactured parts of this product that, upon inspect: son by Peripheral Electronics authorized personnel, is found to have failed in normal use due to defects in material or workmanship.
Please check out our other products including: Auxiliary. Programmable auxiliary input device Complete universal CD changer that connects to most factory stereos www.peripheralelectronics.com Peripheral Electronics®, a division of AMP of America™ 13160 56th Court Clear water, Florida 33780 866-788-4237 in the US or 727-572-9255 ext.262 for international calls suppori@peripheralelecironics com ©2006 AAMP™ of Florida, Inc.
Installation Note: When installing a PXHTY3 harness in any. 2006.or newer Toyota vehicle; if the audio becomes muted on all audio sources (CD, Tuner, etc), it will be necessary to cut the green wires on the harness. Cut and insulate all the green wires that come out of pin 21 in the 22-pin connector that plugs into the interface.
There are 3 convenient ways fo mount the cradle in the car. 1) Dash mount with adhesive tape 2) AC vent mount 3} Sower mount Mara-Make sure the dash surface is clean and dry before using adhesive tape Once the mounting plate is installed an the back of the cradle, place your pad in the padded surface on the front of the cradle and gently squeeze the arms on Bach SIDS to secure. For more information visit www garipheralafestronis. com.
