Santorini II Fiesta 10-ft Square Cantilever Solar LED Umbrella with Sunbrella® Fabric Please Do N ot Hesitate to Contact Our Consumer H otline at 800-759-0 977 with Any Qu estions That May Arise During Assembly or Use of This P roduct! NU6245B • NU6250B • NU6255B Ver. 0219LP www.bluewaveproducts.
PACKAGE CONTENTS A – (1) Main Umbrella* B – (1) Plastic Water Fillable Stand (incl.
ASSEMBLY INSTRUCTIONS Carefully check all packaging materials before discarding. Do not assemble if there are missing pieces. Step 1 Put the stand on a level ground where you intend to locate your umbrella. Open the cap on the top of the stand & fill the stand with water. Then tighten the cap. In case you want to move the stand, Step 2 Put the Base Pole (C) on the top of the Plastic Water Fillable Stand (B).
Step 3 Attach the Base Pole (C) on the top of the Plastic Water Fillable Stand (B) with Bolts (F) & Washers (G), using the Allen Wrench (E) to tighten Bottom crank hole C E F G B Step 4 Place the Swivel Cover (D) around the Base Pole (C). C Bottom crank hole Locking hole for threaded knob side A +/- 1.4” B D Side B +/-1.7” side B Important Notice : Pay attention to the size of the middle hole in the Swivel Cover (D). Side A / Front Side : +/- 1.4", Side B / Rear Side : +/- 1.7".
Step 5 Attach the Solar Panel (K) to the top of the umbrella. 1 : Insert the plug into the socket under the Solar Panel (K). 1 2 : Put the Solar Panel (K) on the top of umbrella and hide the plug and wire inside the groove at the top of umbrella. Then turn the Solar Panel (K) clockwise. Do not over tighten.
Step 6 Put the Main Umbrella (A) over the Base Pole (C) Important Notice : When you put the Main Umbrella (A) onto the Base Pole (C), make sure the locking holes are on the same side .
Step 7 Screw the Threaded Knob (H) into the locking hole clockwise.
Step 8 There are 3 Crank Holes on your umbrella. Top crank hole for canopy tilting, Bottom crank hole for 360 degree rotation. Middle crank hole for umbrella opening and closing.
Step 9 Squeeze the trigger before attempting to raise the crank housing. Insert the Crank Handle (I) into the middle crank hole and turn clockwise to extend umbrella fully. A 1 I 2 I B CAUTION: Please pull and loosen the umbrella ribs by hand, so they're not entangled, before attempting to open the umbrella by crank.
Step 10 Squeeze trigger and lift up to desired height.
Step 11 Insert the Crank Handle (I) into the top crank hole to tilt your umbrella canopy.
Step 12 Insert the Crank Handle (I) into the bottom crank hole to rotate your umbrella 360 degrees.
Step 13 Squeeze the trigger before attempting to lower the crank housing. Turn the crank handle counter-clockwise to close the umbrella, then squeeze and pull down on trigger to lower. A First Step I Second Step I B Step 14 When not in use, place Umbrella Cover (J) over the umbrella.
Battery Charging YOU MUST CHARGE BATTERIES BEFORE FIRST USE. • Please note that batteries can discharge if they are left unused or uncharged for a long period of time. We recommend you charge your solar umbrella for at least 8 hours in direct sunlight before the first use. Failure to charge the batteries will result in premature dimming of the lights in your new solar umbrella. MAKE SURE THE LIGHT SWITCH IS IN THE OFF POSITION WHEN CHARGING THE SOLAR PANEL (see illustration at left).
Battery Replacement We recommend that you change the batteries in your solar light umbrella every year or when you feel the light output is diminished. Use only three (3) AA size Ni-MH 1600mAh rechargeable batteries from any major retailer. · Install only new batteries of the same type in your product. · Failure to insert batteries in the correct polarity, as indicated in the battery compartment, may shorten the life of the batteries or cause batteries to leak.