Foreword This Instruction Manual Is the standard version for all modals for the packaged terminal alr conditioners manufactured by our company. The appearance of the mode that you purchased may be slightly different from the ones described In the Manual, but it does not affect the proper operations and usage. Please read this Manual carefully and keep the Manual available for reference ata later time.
Read this Manual carefully before using the packaged terminal air conditioner to ensure proper operation of the unit. INSTRUCTIONS TO INSTALLATION @ Make sure that an authorized technician or contractor doss the installation for you ~~ N= Make sure that breaker is installed for safe Rh operations. Q Earth Leakage Circuit Barker If brisker Is nat Installed, ft ma roe ult In eclectic shock or either hazards. Do not Install the unit In a place where there might be leakage of inflammable gases.
A CAUTION of the package terminal ai conditioner by pulling the power cable from the socket 5, = Do not try to stop the operation) Make sure that there is no dust on the plug before you plug in the power socket and make sure the plug is put put correctly plugged into the socket. there ls Huston the plug or the plug ls not proper dare, ls could rebut N Try as much as possible to avoid the sunlight and warm air from entering the room.
CATIONS OF Front View Flee screen Air outset to take out directly grasping from hers oul Alr bigwig out from hare. Operation panel Air return grids for Intake of room air Rear View Outdoor grille TORE TURD Ch FEE CE, CEI A FEE Air inlet Alr inlet Alr discharge vent Features and appearance wil vary all the figures provide a demonstration to Introduce the function.
cnn oot von pin petunias pon I VE oae a, —c er paces nt meh cat rig oaten] [Operation mode Indicator lamp decrement tha temperature Fry or] | cm roar | 22 JIT) Fo ps eating tote SD machine ON or OFF. ‘Operation running indicator (amp io mir Paar Prom bi mister's | | reservist scent tur rims | | mss Change from Fahrenheit to Celsius Press AA and 7 key simultaneously for 3 seconds. Temperature Limiting Set Post Ranges Press /\ key and FAN SPEED key simultaneously,into R1-R8 lower and higher limit temperature
WONTED Fresh alr exchange procedure 1.Remove the front cover by pulling out at the bottom to reseals It,then lift It up to clear the tall along the chassis topping a). 2 put the air exchange switch to open state(Fig b). Fig Note: ‘The alr exchange switch Is normally placed at the left closed position.
TED Wall mounted controller and hand held remote controller are optional parts, please read the actions corresponding to the specific model you have choose. Room temperature Indicator] [Bat temperatures indicator | [Fan indication] — GRUFF bun Pres th bon ofr te machine O Nor OFF ODE bin FAN MID button Press th in 2 sect re Pre bis ton persons among cou fan hel FANDOM | PANHANDLE WARM | OWED —— FA GH bani Enc preen of Fie but wil ree the roe me ait] | L1H Erin Sara Ta Fn i high speed.
TE | Post ion mode conductor on wi | BHT om mmr re esr REE. TT me = rea PASSED ten oO Lemme oe sped ow pad rk da. Woe HOLD bunion re STO J Rms Em = SPR Hom Above figure shows all indications for the purpose of explanation, practically only the applicable is indicated. Cool/Fan/Heat mode operation procedure @ Press the ON/OFF button with the remote controller pointing toward the packaged terminal air conditioner.
When cells ara Inserted, the present time Is automatically set to AM 0:00 EX :set to AM10:30. @® Open the back corpuscular the CLK button The time Indicator Is flickering and can set the present time. ® Press the HOUR button (set to AM 10:00) ® Press the MIN button. (set to 30) @® Press the CLK button again,and then close the back cover. Timer operation procedure Timed switch-off ® During the operation ,press the TIMER button and the unit will enter the timed switch-off mode.
Before proceeding with the methods of maintenance, aka sure that the packaged terminal alr conditioner is muted off and the plug is pulled out from the socket. TEE LL TY Check to ses If there are any blocking objects around the air inst and outlet of the units. Hack to ses If the Installation bass Is commode or rusty. Check if the grounding is properly made. Check If the alr fighter screen Is clean. Connect to the power source Load batteries In the remote controller.
Inspection and treatment prior to maintenance Please check the following items before asking our company dealer or authorized technician for after-sale services: Tha packaged terminal alr conditioner doss not work at all. properly? Is the power plug Inserted Into the socket fe Is theta a power allure of. is the fuse blown? awh om Is the timer set for the “TIMER-ON" mode? terminal air conditioner (remote controller \ start operating before the set time rested or 81°F 2 made, wil not | 1780.
SON N= To ensurers the unit operates safely and efficiently, must be installed by qualified or experienced technicians. © The appliance must bs installed in accordance with national wiring regulations. « If the supply cord is damaged,it must be replaced by the manufacturer service agent or a qualified technician in order to avoid a hazard. 1.NAMES OF PARTS 2 WALL SLEEVE AND OUTDOOR GRILLE 1)The wall sleeve must be proper installed according to the wall sleeve installation instructions {Pageantry.
SON P 2) Chassis installation Slide the chassis into the wall sleeve until the chassis flanges contact the front edge of the wall sleeve, then secure with four screws through the chassis flange holes. Wail Soave Ci . a Outsides Wall oa ‘Side Chassis in 3) Wires connection of wall mounts controller (optional procedure, It Is Just sultanas for wall mounted controller model) Fly connect the electrical functor of wall mounted controller to the Functor on the right bottom of chassis.
EVE | To ensure the best performance of the packaged terminal air conditioner please observe the following wall sieve installation procedures and do the installation in accordance with restated requirements. 1.wall sleeve constitutionalism procedure) a)Unpack all parts and accessories,referring to Fig 1,assemble the wall sieve by first bluestocking side pieces to the bottom concupiscent the top piece to the assembled side and op pieces. handle the wall sieve carefully.
Chart 1 Dimensions Recommended Installation clearance D1 Top of to finished 02 Projection of case Into roomer" minimum maximum without use of electrical sub-base. Note: when sub-bass is used. D3 Minimum projection of case to the oulsids1/4" Height above finished floor or top of minimum, D4 Z'recommended without with sub base D5 Firefight side of case to adjacent 3.Preparation of the wall The slave should be Installed during construction and lintels should be used to support the block above the wall sleeve.
If the field supplied case angles must be used during installation(Fig as follows: a)Position the case angles around top and sides of sleeve to get the proper depth, (be sure to have the angles pointing outside). b)Mark the sleeve using the case angles as a template for screws. <)Drill at the marked position, {from step 2 above)only use d}install the screws from the outside of the sleeve,do not drill any holes in the base of the sleeve. mats iG Figs 4.
INST. 5 Weather proofing: Weather roofing gaps between the exterior wall and the sleeve with caulking or other equivalent weather proofing material(Fig 9) Hid a AERIE Fin. SEAS ASE Re Fig Note:installation in extra thick walls: a) If the sleeve is being installed in a thick wall where the sleeve is recessed more than 3°, an extended wall sleeve will be required with depths as called out in chart 1 .
