WCFM500K Central Whole House Water Filtration System INSTALLATION INSTRUCTIONS & OPERATING MANUAL Ver. 01/2021 Copyright ©2005-2021 ISPRING WATER SYSTEMS, LLC. All rights reserved.
We stand behind our products Since 2005, iSpring has been dedicated to providing high-quality drinking water to families across the United States.We provide various residential faucets and water filtration systems that purify your water in everyday life and deliver pure, healthy, and tasty water to you and your family. At iSpring, we strive to develop products to the highest of standards and aim to make excellent drinking water accessible for all households.
Prior to Installation Read this instruction manual carefully prior to installation. Keep this manual readily available for future reference. Table of Contents Installation ..................................................................................................................................................3 Using the System Programming the Central Whole House Water Filtration System ............................... 5 WCFM500K Central Whole House Water Filtration System Operation .................
Installation (1) Water Pressure A minimum of 20 pounds (1.4 bar) of water pressure is required for the regeneration valve to operate effectively. (2) Electrical Facilities An uninterrupted alternating current (A/C) supply is required. (3) Notes • Water pressure should not exceed 125 psi (8.6 bar), water temperature should not exceed 110°F (43°C), and the unit cannot be subjected to freezing conditions.
Step 7. Slowly place the bypass in the service position and let water flow into the mineral tank. When water flow stops, slowly open a cold water tap nearby and let it run until the air is purged from the unit. Step 8. Plug unit into an electrical outlet. All electrical connections must be connected according to local codes. Be sure the outlet is uninterrupted. Step 9. Setting the Time of Day. Step 9. a.
Programming the Central Whole House Water Filtration System (1) Features of the SXT (3) Press and hold "Up" and "Down"at the same time for 5 seconds to enter the following user menu settings: Day Override (Display Code DO): Press the Extra Cycle button. Use this display to set the Day Override. This setting specifies the maximum number of days between regeneration cycles. The system is set to a timer- type control, the day override setting determines how often the system will regenerate.
(4) Press and hold "Extra Cycle" and "Up" at the same time for 5 seconds to view diagnostic data: The SXT control records and maintains diagnostic data to assist with servicing and troubleshooting the water treatment system. Abbreviation Parameter Description HR Hours in Service SV Software Version Displays the software version installed on the controller. Displays the total hours that the unit has been in service since last regeneration. Display Code HR: Press the Up button.
WCFM500K Central Whole House Water Filtration System Operation (1) Product Functions and Features The Central Whole House Water Filtration System is designed for use whenever iron is problematic in the water supply. When water enters the Central Whole House Water Filtration System, it passes through a pocket of compressed air that incorporates oxygen. The water then passes through a filter bed, creating a reaction that separates the iron particles from the water.
Power backup that continues to keep time and the passage of days for a minimum of 48 hours in the event of power failure. During a power outage, the control goes into a power-saving mode. It does not monitor water usage during a power failure, but it does store the volume remaining at the time of power failure. • Day-of-the-Week controls. • While in service, the display alternates between time of day, volume remaining, or days to regeneration. • The Flow Indicator flashes when outlet flow is detected.
Troubleshooting ISSUE The water conditioner fails to regenerate. Loss of water pressure. POSSIBLE CAUSE POSSIBLE SOLUTION Electrical service to the unit has been interrupted. Assure permanent electrical service (check fuse, plug, pull chain, or switch). The timer is defective. Replace timer. Power failure. Reset time of day. Iron buildup in line to water conditioner. Clean line to water conditioner. Iron buildup in water conditioner. Clean control and add the mineral cleaner to the mineral bed.
Error Codes NOTE: Error codes appear on the In Service display. Error Code Error Type Cause 0 Cam Sense The valve drive took Error Reset and Recovery Unplug the unit and examine the power head. longer than 6 minutes Verify that all cam switches are connected to the to advance to the next circuit board and functioning correctly. Verify that regeneration position. the motor and drive train components are in good condition and assembled correctly.
the correct system capacity has been selected, that the day override is set correctly, and that meter is identified correctly. If the unit is configured as a Day-of-Week system, verify that at least one day is set ON. Correct the settings as necessary. 3 Memory Error Control board memory failure. Perform a Master Reset and reconfigure the system via Master Programming Mode. After reconfiguring the system, step the valve through a manual regeneration.
Warranty Registration To register your product for the warranty, visit our website at 123filter.com and go to the “Warranty” tab. We provide a 30-day money-back guarantee, a 1-year manufacturer warranty, and lifetime tech support for all of our products. However, we do not have the order information from websites other than 123Filter.com (Amazon, Home Depot, etc.), so please be sure to fill in that information upon registration of your system.
Atlanta, GA USA iSpringFilter.com For questions, comments, or technical support, contact us at: support@123Filter.com (678) 261-7611 Monday-Friday 8:30 a.m. - 5:30 p.m.
