IS-880PD8 IS -880PD8 Switching Power Supply ( EPS- 880W) SPECIFICATION Revision: 1.0 727 , . Phillips Drive City of Industry. CA 91748. USA http:// www.Xeal.com.
TABLE OF CONTENTS 1. General..................................................................................................................................... 3 2. AC Input Characteristics ........................................................................................................ 3 2.1 AC INPUT VOLTAGE, FREQUENCY AND CURRENT ( RATING: 100V-240VAC, 47-63HZ, 14-7A )..................................3 2.2 AC INRUSH CURRENT .......................................................................
1. General This is the specification of Model IS-880PD8; it is intended to describe the functions and performance of the subject power supply. This PS/2 880 watts switching power supply with Active PFC (Power Factor Correction) capability, meets EN61000-3-2 and equips Full Range Input features. 2. AC Input Specifications 2.1 AC Input Voltage, Frequency and Current ( Rating: 100V-240Vac, 47-63Hz, 14-7A ) The power supply must operate within all specified limits over the input voltage range in Table 1.
Multiple rails for +12V Output Voltage +5V +3.3V +12V1 +12V2 +12V3 +12V4 -12V +5VSB Max. Load 30A 28A 18A 18A 18A 18A 0.5A 4A Min. Load 1.0A 0A 0.8A 0.8A 0.8A 0.8A 0A 0.1A 6W 20W Max. Combined 180W 72A 860W Total Output Table 5 – Output Loads Note 1: Maximum continuous total DC output power should not exceed 880 W. Note 2: Single / Multiple rail(s) for +12V is adjustable by a switch. 3.
3.3 Timing Requirements These are the timing requirements for the power assembly operation. The output voltages must rise from 10% to within regulation limits (Tvout_rise) within 5 to 70mS. The +5V, +3.3V and +12V output voltages should start to rise at about the same time. All outputs must rise monotonically. The +5V output needs to be greater than the +3.3V output during any point of the voltage rise. The +5V output must never be greater than the +3.3V output by more than 2.25V.
Table 11 – Turn On/Off Timing Item Description Tsb_on-delay MIN MAX Units Delay from AC being applied to +5VSB being within regulation. 1500 mS Tac_on-delay Delay from AC being applied to all output voltages being within regulation. 2500 mS Tvout_holdup All main output voltage stay within regulation after loss of AC 18 mS Tpwok_holdup Delay from loss of AC deassertion of PWOK. 17 mS Tpson_on_delay Delay from PSON# active to output voltage within regulation limits.
3.4 Remote On/Off Control : PSON# The PSON# signal is required to remotely turn on/off the power supply. PSON# is an active low signal that turns on the +5V, +3.3V, +12V and –12V power rails. When this signal is not pulled low by the system, or left open, the outputs (except the +5VSB and V bias) turn off. This signal is pulled to a standby voltage by a pull-up resistor internal to the power supply. Signal Type Accepts an open collector/drain input from the system. Pull-up to VSB locted in power supply.
Voltage Minimum Maximum Shutdown Mode +5V +5.7V +6.5V Latch Off +3.3V +3.9V +4.5V Latch Off +12V1,2,3,4 +13.3V +14.5V Latch Off 5VSB 5.7V 6.5V Auto recovery Table 15 –Over Voltage protection 4.3 Short Circuit Protection The power supply shall shut down in a latch off mode when the output voltage is short circuit. 5. Environmental Requirements 5.1 Temperature Operating Temperature Range: 0°C ~ 50°C (32°F~ 122°F) Non-Operating Temperature Range: -40°C ~ 70°C (-40°F~ 158°F) 5.
6.2 AC Input Leakage Current Input leakage current from line to ground will be less than 3.5mA rms. Measurement will be made at 240 VAC and 60Hz. 7. Reliability 7.1 Mean Time Between Failures (MTBF) The MTBF of the power supply shall be calculated utilizing the Part-Stress Analysis method of MIL217F or Bell core RPP. The calculated MTBF of the power supply shall be greater than 100,000 hours under the following conditions: Full rated load 120V AC input Ground Benign 25°C 7.
P2: Processor Power Connector (sectional connector 4-Pin + 4-Pin) Connector housing: 8- Pin Molex 5557 (39-01-2080) or Equivalent Contact: Molex 5556T (39-00-0059) or Equivalent Pin Signal Color Size Pin Signal Color Size 1 COM Black 18 AWG 5 +12 VDC1 Yellow/Black stripe 16 AWG 2 COM Black 18 AWG 6 +12 VDC1 Yellow/Black stripe 16 AWG 3 COM Black 18 AWG 7 +12 VDC2 Yellow 16 AWG 4 COM Black 18 AWG 8 +12 VDC2 Yellow 16 AWG 4-Pin HDD / CD-ROM Drive Power Connectors Connec
PCI-Express 8-Pin Pin Signal Color Size Pin Signal Color Size 1 +12 V4 Yellow/Green stripe 18 AWG 5 COM Black 18 AWG 2 +12 V4 Yellow/Green stripe 18 AWG 6 COM Black 18 AWG 3 +12 V4 Yellow/Green stripe 18 AWG 7 COM Black 18 AWG 4 COM Black 18 AWG 8 COM Black 18 AWG 9. Physical Characteristics Size 9.1 Power Supply Dimension: 150 mm(W) x 86 mm(H) x 190 mm(D) Mechanical drawing: Please refer to the attached sketch.
