TC-1200PD1 TC-1200PD1 Switching Power Supply ( 1200W PS2 ATX12V ) SPECIFICATION Revision: 1.0 727 , . Phillips Drive City of Industry. CA 91748. USA http:// www.Xeal.com.
1.0 INPUT: 1.1 VOLTAGE 1.2 FREQUENCY 1.3 CURRENT 1.4 INRUSH CURRENT 1.5 POWER EFFICIENCY 1.6 LEAKAGE CURRENT 1.7 POWER FACTOR 2.0 OUTPUT: 2.1 REMOTE ON/OFF 2.2 HOLD-UP TIME 2.3 POWER GOOD DELAY 2.4 POWER FAIL DELAY 2.5 TURN-ON DELAY TIME 2.6 TRANSIENT OVERSHOOT 2.7 RISE TIME 3.0 PROTECTION: 3.1 OVER CURRENT PROTECTION 3.2 OVER VOLTAGE PROTECTION 3.3 SHORT PROTECTION 3.4 UNDER VPLTAGE PROTECTION 4.0 ENVIRONMENT: 4.1 OPERATING TEMP 4.2 STORAGE TEMP 4.3 OPERATING HUMIDITY 4.4 STORAGE HUMIDITY 4.
6.0 CE REQUIREMENTS: 6.1 CONDUTED EMI 6.2 SAFETY STANDARDS 7.
1.0 INPUT: 1.1 VOLTAGE MINIMUM NOMINAL MAXIMUM UNITS 90 100~240 264 Vrms 1.2 FREQUENCY 47Hz ~ 63Hz 1.3 CURRENT 100Vac / 15A max. 1.4 INRUSH CURRENT 65A max. when AC input 115Vac at 250C cold start. AC input 230Vac at 250C cold start power no damage. 1.5 POWER EFFICIENCY 80% (min.) at full load(typical) and 115Vac input. 1.6 LEAKAGE CURRENT 3.5mA max. 1.7 POWER FACTOR PF > 0.9 2.0 OUTPUT: Voltage Max load Min load ϠRipple & Noise !ϠϠRegulation Max output +12V1 +12V4 +3.
LOAD REGULATION TEST TABLE +12V1 +12V2 +12V3 +12V4 +5V +3.3V -12V +5Vsb LOAD1 1A 1A 1A 1A 0.5A 0.5A 0A 0.1A LOAD2 3A 3A 5A 5A 5.5A 5.5A 0.15A 0.5A LOAD3 4.5A 4.5A 7A 7A 9A 9A 0.25A 1A LOAD4 5.5A 5.5A 10A 10A 11A 12A 0.35A 1.3A LOAD5 7.5A 7.5A 12A 12A 15A 14A 0.4A 1.7A LOAD6 8.5A 8.5A 14.5A 14.5A 19A 18A 0.5A 2A LOAD7 9.5A 9.5A 17.5A 17.5A 21A 21A 0.6A 2.3A LOAD8 10.5A 10.5A 20A 20A 25A 25A 0.7A 2.8A LOAD9 12.5A 12.
2.7 RISE TIME 20ms max at full load. 3.0 PROTECTION: When OCP, OVP, UVP, OTP, OPP, or short protection is triggered, the main outputs will be latched off. The main outputs can be reset by cycling the DC remote on/off or AC power. +5Vsb output is auto recovery when fault condition removed. 3.1 OVER CURRENT PROTECTION +12V1 & +12V2 22A~35A +12V3 & +12V4 39A~55A +5V 33A~50A +3.3V 33A~50A 3.2 OVER VOLTAGE PROTECTION +3.3V output 4.5 Vmax. +5.0V output 7.0 Vmax. +12.0V output 15.6 Vmax. 3.
5.0 HI-POT :( Input/Output isolation) 5.1 PRIMARY TO SECONDARY 3535Vdc for 3 seconds 5.2 INSULATION RESISTANCE Primary to earth ground 500Vdc, 50M ohms Min. 6.0 CE REQUIREMENTS 6.1 CONDUCTED EMI 1. MEET FCCΚ Class B 2. MEET CISPR 22Κ Class B 3. MEET BSMIΚ Class B 6.2 SAFETY STANDARDS 1. MEET CUL (UL 60950) 2. MEET TUV EN60950 3. MEET CB (IEC60950) ! 4. MEET CE 5. MEET CCC 6.3 HARMONIC MEET IEC1000-3-2, Class D 7.
