Quick Start Guide
WARRANTY &
WATCH CARE
*SEE THE QUICK START GUIDE FOR
QUICK SETUP INSTRUCTIONS
ROUND SMARTWATCH
SAFETY & SKIN CARE
We want to make sure that you’re
comfortable in your new iTECH
Fusion Round Smartwatch. Here
are a few tips that should help:
Regularly clean your smartwatch with a
moist paper towel (please pat dry your
watch once complete)
Keep your wrist free of any dirt and oils
Keep your watch loose enough so that
three of your ngers can t underneath
your watch while it’s being worn (wearing
a watch too tight can cause skin irritation
due to sweat or other types of moisture)
After a workout, it’s advised to remove
your watch to allow your wrist, watch,
and yourself to take a breather
Adults with eczema or a skin condition
should consult a physician before
wearing the watch
Please wear with care!
WATCH CARE
Clean your band regularly, especially after
strenuous exercise. It is recommended to
rinse your band with water or wipe it with an
alcohol wipe. Do NOT use any kind of soap,
hand sanitizers, or household cleaners,
which could get trapped beneath the band
and irritate your skin.
It’s a good idea to set your watch aside
for 10-15 minutes after cleaning to ensure
that the device is fully free of any potential
irritants and completely dry.
For stains or buildup on your band, watch
screen or casing, wipe the affected area with
an alcohol wipe. Be sure to use a little force
while wiping. If affected area is on the band,
you can use warm water and a soft bristle
brush to remove the dirt, stain or build up.
To keep your device looking new, its recom
-
mended to use a microber cloth to wipe off
any smudges or ngerprints from the casing,
screen and band.
Your watch should always help you feel
great but if you experience any irritation or
skin abrasion, please remove the watch and
consult a doctor.
WATCH INSTRUCTIONS
FOR METAL BANDS
EASY SELF-ADJUSTABLE LINKS
Lift tab at end of center section on last link.
Open clasp and remove link.
ADJUSTING METAL BAND USING
HAIR TYPE PIN CONSTRUCTION
1. Insert an awl or other slim metal tool into hole. Tool should
be facing the same direction as the arrow indicated on the
bottom side of the band.
2. Press tool until the pin comes through the opposite end.
Using pliers, pull the pin out and remove the link. Repeat this
process to remove the desired number of links.
ADJUSTING WATCH BANDS FOR LEATHER, SILICONE,
FABRIC & PLASTIC STRAPS
Use the prong and notch system to move the
prong up or down a notch to tighten or loosen
and adjust to the appropriate fit for your wrist.
SETTING THE TIME
1. Gently pull crown out
2. Rotate crown until hands are positioned at time.
3. Firmly push crown in. This will activate the watch.
FOR STRAPS WITHOUT HOLES IN THE LUG
Lay your watch with the face down (preferably on
a cloth to prevent scratching your watch). You will
need a sharp point or “spring bar tool” to perform
the following steps.
1. Insert the sharp point between the strap and watch lug to
release strap from case.
2. Once the spring bar is detached, you can remove your
strap. To reattach, depress spring bar and insert into hold on
the inside of the watch case lug.
FOR STRAPS WITH SMALL HOLES IN THE LUG
1. Carefully place your watch face down on a folded cloth to
avoid damaging the lens.
2. Carefully insert the round end of the watch tool into the
hole, toward the center of the strap. The spring bar should
come free of its location hole.
3. Lift out the strap and spring bar.
SPRING BAR TOOL SPRING BAR TOOL
FOR LEATHER, SIMULATED LEATHER, PLASTIC, FABRIC &, SILICONE BANDS
CHANGING / REPLACING / ADDING / REMOVING THE BAND FROM YOUR WATCH