User's Guide

FOR LEATHER, SIMULATED LEATHER, PLASTIC, FABRIC &, SILICONE BANDS
SPRING BAR TOOL SPRING BAR TOOL
WATCH INSTRUCTIONS
FOR METAL BANDS
EASY SELF-ADJUSTABLE LINKS
Lift tab at end of center section on
last link.
Open clasp and remove link.
ADJUSTING METAL BAND USING
HAIR TYPE PIN CONSTRUCTION
1. Insert an awl or other slim metal tool into hole.
Tool should be facing the same direction as the
arrow indicated on the bottom side of the band.
2. Press tool until the pin comes through the opposite
end. Using pliers, pull the pin out and remove
the link. Repeat this process to remove the desired
number of links.
ADJUSTING WATCH BANDS FOR LEATHER, SILICONE,
FABRIC & PLASTIC STRAPS
Use the prong and notch system to move the prong
up or down a notch to tighten or loosen and adjust to
the appropriate fit for your wrist.
FOR STRAPS WITH SMALL HOLES IN THE LUG
1. Carefully place your watch face down on a folded cloth
to avoid damaging the lens.
2. Carefully insert the round end of the watch tool into the
hole, toward the center of the strap. The spring bar
should come free of its location hole.
3. Lift out the strap and spring bar.
FOR STRAPS WITHOUT HOLES IN THE LUG
Lay your watch with the face down (preferably on
a cloth to prevent scratching your watch).
You will need a sharp point or “spring bar tool” to
perform the following steps.
1. Insert the sharp point between the strap and watch lug
to release strap from case.
2. Once the spring bar is detached, you can remove your
strap. To reattach, depress spring bar and insert into
hold on the inside of the watch case lug.
FIND OUR APP IN YOUR APP STORE
To set up your watch, please go to:
https://www.itechwearables.com/setup
Select iTech Sport and download the user guide manual
For customer support, please contact
[e-mail]
SAFETY & SKIN CARE
We want to make sure that you’re
comfortable in your new iTECH
Sport Fitness Tracker. Here are a
few tips that should help:
Regularly clean your tness tracker with
a moist paper towel (please pat dry your
watch once complete)
Keep your wrist free of any dirt and oils
Keep your tness tracker loose enough
so that three of your ngers can t
underneath your watch while it’s being
worn (wearing a watch too tight can
cause skin irritation due to sweat or other
types of moisture)
After a workout, it’s advised to remove
your tness tracker to allow your wrist,
watch, and yourself to take a breather
Adults with eczema or a skin condition
should consult a physician before
wearing the tness tracker.
Please wear with care!
WATCH CARE
Clean your band regularly, especially after
strenuous exercise. It is recommended to
rinse your band with water or wipe it with an
alcohol wipe. Do NOT use any kind of soap,
hand sanitizers, or household cleaners,
which could get trapped beneath the band
and irritate your skin.
It’s a good idea to set your watch aside
for 10-15 minutes after cleaning to ensure
that the device is fully free of any potential
irritants and completely dry.
For stains or buildup on your band, watch
screen or casing, wipe the affected area with
an alcohol wipe. Be sure to use a little force
while wiping. If affected area is on the band,
you can use warm water and a soft bristle
brush to remove the dirt, stain or build up.
To keep your device looking new, its
recommended to use a microber cloth to
wipe off any smudges or ngerprints from
the casing, screen and band.
Your tness tracker should always help you
feel great but if you experience any irritation
or skin abrasion, please remove the watch
and consult a doctor.
CHANGING / REPLACING / ADDING / REMOVING THE BAND FROM YOUR WATCH
FITNESS TRACKER
QUICK START GUIDE