Users Manual

ManualsBrandsIveda ManualsNetwork HardwareWireless Communication Bluetooth Module

1 Product introduction

1.1 Product description

CC2640R2F device is a wireless microcontroller (MCU), which is mainly

suitable for Bluetooth® 4.2 and Bluetooth 5 low-power application .This device

belongs to the SimpleLink™ CC26xx series, which is an ultra-low power

consumption 2.4ghz RF device, with extremely low active RF and MCU currents

and low power mode current consumption, it ensures excellent battery life and

is suitable for small button battery power and energy acquisition applications.

SimpleLink Bluetooth The low-power CC2640R2F device contains a 32-bit

ARM Architecture ®-M3 kernel (operating at the same frequency as the main

processor) and has a rich set of peripheral features, including a unique

ultra-low-power sensor controller. The sensor the controller is ideal for

connecting external sensors and for autonomously collecting analog and digital

data while the rest of the system is in sleep mode. Therefore, CC2640R2F device

becomes an ideal choice for various applications that focus on battery life, small

size and simple practicality.

CC2640R2F module adopts PCB onboard antenna, with an 8M flash outside,

which is more convenient for product development and expansion.

Picture 1.1 Appearance of product

Summary of content (7 pages)

PAGE 1
Product introduction 1.1 Product description CC2640R2F device is a wireless microcontroller (MCU), which is mainly suitable for Bluetooth® 4.2 and Bluetooth 5 low-power application .This device belongs to the SimpleLink™ CC26xx series, which is an ultra-low power consumption 2.4ghz RF device, with extremely low active RF and MCU currents and low power mode current consumption, it ensures excellent battery life and is suitable for small button battery power and energy acquisition applications.
PAGE 2
Picture 1.2 Dimensions of product Picture 1.3 Bblock Diagram of product 2 Features and Superiority 2.1 Superiority  Microminiature module solution  Ready for product development quickly  Minimizes product development time 2.2 Module Features     Working on 2.
PAGE 3
     Current 9.1mA at TX power 5 dBm Current 5.9 mA at RX Operation voltage 2.8V~3.8V Receiver sensitive:–97dBm Internal temperature sensor 3. Hardware description 3.1 Pin description Pins layout for CC2640R2 module as shown on below picture 3.3, module designed with three rows of stamp hole patch interface with 20 pins, and pin spacing is 2.2mm. Picture 3.
PAGE 4
GPIO, Sensor Controller, 7 DIO_13 Digital/Analog I/O 8 DIO_14 Digital/Analog I/O 9 JTAG_TMSC Digital I/O 10 JTAG_TCKC Digital I/O 11 DIO5 Digital I/O 12 DIO6 Digital I/O 13 VDD Power 14 GND Power 15 DIO7 Digital I/O 16 RESET_N 17 DIO11 GPIO SPI Flash used，Leave it float 18 DIO10 GPIO SPI Flash used，Leave it float 19 DIO9 GPIO SPI Flash used，Leave it float 20 DIO8 GPIO SPI Flash used，Leave it float Analog GPIO, Sensor Controller, Analog JTAG TMSC, high-drive capa
PAGE 5
4.Antenna layout specification The CC2640R2 module is designed with a PCB onboard antenna with a vertical polarization near omnidirectional radiation. This provides the effect of wireless signal radiation without any additional ground plane, but it is important to note that the specification is followed when installing this type of module to another PCB. The area around the antenna must be kept at least 20 mm with wires or other metal objects. This applies to all layers of a PCB, not just the top layer.
PAGE 6
FCC statement This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
PAGE 7
Integration instructions for host product manufacturers according to KDB 996369 D03 OEM Manual v01 2.2 List of applicable FCC rules FCC Part 15.247. 2.3 Specific operational use conditions This device is intended only for OEM integrators under the following conditions: 1) The transmitter module may not be co-located with any other transmitter or antenna. As long as the condition above is met. further transmitter test will not be required.