Installation & Assembly

ManualsBrandsIvy Bronx ManualsBeds & HeadboardsEyre Upholstered Panel Headboard

Page 1 of 6

HEADBOARD

Hardware:

mponent:

Bolt M8x45mm x4

Flat Washer M8xD22mm x4

Allen Wrench M5 x1

Hea

dboard x1

Low Post x2

Thank you for purchasing the

HEADBOARD！

！！

！

Before you start, here is some helpful advice:

1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step

instructions.

2.Owing to the size and weight of the headboard, we recommend that it is assembled by two adults, on a carpeted

or padded area, in the room that it is intended for. Approx assembly time: 30 minutes.

3.Please do not use any tools other than those provided or recommended in these instructions.

4.Please do not throw away any of the packaging or the instruction until you have checked all the components and

hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe

environmentally friendly way.

5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the

components from time to time, so please save the tools that has been provided.

6.Please keep all fitting out of reach of children.

(Styl

e may vary)

Summary of content (6 pages)

PAGE 1
HEADBOARD Thank you for purchasing the HEADBOARD！！ Before you start, here is some helpful advice: 1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step instructions. 2.Owing to the size and weight of the headboard, we recommend that it is assembled by two adults, on a carpeted or padded area, in the room that it is intended for. Approx assembly time: 30 minutes. 3.Please do not use any tools other than those provided or recommended in these instructions.
PAGE 2
HEADBOARD STEP 1: Put the Headboard (1) upside down on a carpeted or padded area by two adults Then insert the Low Posts (2) into the bottom of Headboard (1) and align pre-drilled Low Post (2) holes to the predrilled Headboard (1) Holes according to your desired headboard height. Attach each of Low Post (2) by using 2 piece of Flat Washer (B) and 2 pieces of Bolt (A) from the holes on the back of Low Post (2) and Headboard (1). Tighten with Allen Wrench (C).
PAGE 3
CONNECTING HEADBOARD TO BED FRAME ASSEMBLY INSTRUCTIONS OPTION 1 Hardware: OPTION 1 Component: A Bolt M6x45mm x4 B Bolt M6x65mm x4 C Flat Washer M6xD22mm x8 D Spring Washer M6 x4 E Hex Nut M6 x4 F Allen Wrench M4 x1 1 2 OPTION 1 1 Headboard (Style may vary) x1 2 Bed Frame Page 3 of 6 x1
PAGE 4
CONNECTING HEADBOARD TO BED FRAME Note: Extra hardware were provided for attaching the headboard to your Bed Frame (use is optional). STEP 1: Line up the Bed Frame (2) board’s pre-drilled holes to match those of the Headboard (1) . Secure the Headboard (1) to the Bed Frame (2) by using 2 pieces of Bolt (B) for the thicker Bed Frame (2), and 2 pieces of Bolt (A) for the thinner Bed Frame (2). Before inserting each bolt, place 1 piece of Spring Washer (D) and Flat Washer (C) on each bolt.
PAGE 5
CONNECTING HEADBOARD TO BED FRAME ASSEMBLY INSTRUCTIONS OPTION 2 Note: This is assembly instruction for Headboard connect toBed Frame Hardware: OPTION 2 A Bolt M6x45mm x4 B Bolt M6x65mm x4 C Flat Washer M6xD22mm x4 D Spring Washer M6 x4 F Allen Wrench M4 x1 Component: 1 2 OPTION 2 1 Headboard (Style may vary) x1 2 Bed Frame (Style may vary) Page 5 of 6 x1
PAGE 6
CONNECTING HEADBOARD TO BED FRAME STEP 1: Line up the Bed Fame (2) board’s pre-drilled holes to match those of the Headboard (1). Secure the Headboard (1) to the Bed Frame (2) by using 2 pieces of Bolt (B) with 2 pieces of Spring Washer (D), 2 pieces of Flat Washer (C) for the thicker Bed Frame (2), and 2 pieces of Bolt (A) with 2 pieces of Spring Washer (D), 2 pieces of Flat Washer (C) for the thinner Bed Frame (2). Then tighten the Bolts (A or B) by using the Allen Wrench (F).