Datasheet

ManualsBrandsIXXAT ManualsRemote MaintenanceCAN repeater CAN Bus 12 Vdc, 24 Vdc

Table Of Contents

V1.0

www.ixxat.com

Page 1 of 3

The modular CAN repeater CAN-CR200 with two CAN interfaces

and one CAN backbone interface can be used to improve the

load capacity of the CAN bus with nodes, to establish a physical

coupling of CAN bus systems or to insert a galvanic isolation.

The CAN-CR200 creates the necessary flexibility to optimize the

structure of CAN networks and to free CAN networks from the

restriction to the bus structure. It can be used to implement tree

or star topologies as well as stub lines. For creating star or tree

topologies, several CAN-CR200 can be connected to a CAN-hub

via the integrated backbone bus.

The CAN-CR200 separates a defective segment from the rest of

the network, allowing the remaining network to continue

working.

FEATURES AND BENEFITS

ORDER NUMBER 1.01.0067.44010

Display 3 x CAN status LED (duo LED for communication and errors), Power LED

CAN channels (high-speed) 2

CAN bus interface ISO 11898-2 with CAN choke. 2 x D-Sub 9 connectors; 1 x backbone bus

CAN bit rates Up to 1 Mbit/s

CAN bus termination resistors 120 Ohm switchable via DIP switch

CAN high-speed transceiver SN65HVD251

Galvanic isolation 1 kV DC / 1 sec, 500 V AC /1 min; CAN 1, CAN 2 and backbone bus are

galvanic isolated against each other

CAN propagation delay (typical) Typ. 200 ns (40 m bus length)

Power supply +9 V to +32 V DC

Cost savings due to simple wiring

■

Almost no influence on real-time behavior

■

Greater flexibility in CAN network design

■

Separates a defective segment, allowing the remaining network

to continue working

■

Increased system reliability

■

2 x CAN interfaces

■

DIN-Rail backbone bus to line up and connect repeaters easily

■

Galvanic isolation

■

DATASHEET

CAN-CR200

Summary of content (3 pages)

PAGE 1
DATASHEET CAN-CR200 The modular CAN repeater CAN-CR200 with two CAN interfaces and one CAN backbone interface can be used to improve the load capacity of the CAN bus with nodes, to establish a physical coupling of CAN bus systems or to insert a galvanic isolation. The CAN-CR200 creates the necessary flexibility to optimize the structure of CAN networks and to free CAN networks from the restriction to the bus structure. It can be used to implement tree or star topologies as well as stub lines.
PAGE 2
ORDER NUMBER 1.01.0067.44010 Power consumption at 24 V Typ. 41 mA, max. 100 mA Operating temperature -20 °C to +70 °C Weight Approx. 300 g Dimensions 22.5 x 100 x 118 mm Storage temperature -40 °C to +85 °C Protection class IP30 Relative humidity 10 to 95 %, non-condensing Certification CE, FCC Housing material CERTIFICATES Polyamid ACCESSORIES ORDER NUMBER T bus connector 1.04.0073.00000 Termination adapter for CAN/CAN FD (D-Sub male to female) 1.04.0075.03000 CAN cable 2.
PAGE 3
PIN ALLOCATION TECHNICAL DRAWING 4 +9 V to +32 V DC 0V - 1 2 3 4 CAN CONNECTOR D-Sub 9 22.5 mm 118 mm 4 1 2 2 Pin no. 2 3 7 Signal CAN-Low CAN-GND CAN-High 1 CAN CONNECTOR TBUS 1 4 5 V1.0 www.ixxat.