Safety Data Sheet According to OSHA Hazard Communication Standard, 29 CFR 1910.1200 Initial preparation date: 02.11.2019 Revision date: 06.07.2023 SECTION 1: Identification Product identifier Product name: J-B Weld Plastic Bonder Tan - Part B Product code: 50133 Recommended use of the product and restriction on use Relevant identified uses: Not determined or not applicable. Uses advised against: Not determined or not applicable. Reasons why uses advised against: Not determined or not applicable.
Safety Data Sheet According to OSHA Hazard Communication Standard, 29 CFR 1910.1200 Initial preparation date: 02.11.2019 Revision date: 06.07.2023 Page 2 of 11 SECTION 3: Composition/information on ingredients Identification Name Weight % CAS number: 14807-96-6 Talc 25-30 CAS number: 110-85-0 Piperazine 0.1-0.5 CAS number: 1318-02-1 Zeolite 0.5-1.5 CAS number: 280-57-9 1,4-Diazabicyclooctane 0.1-0.
Safety Data Sheet According to OSHA Hazard Communication Standard, 29 CFR 1910.1200 Initial preparation date: 02.11.2019 Revision date: 06.07.2023 Page 3 of 11 Seek medical attention if irritation, discomfort, or vomiting persists Most important symptoms and effects, both acute and delayed Acute symptoms and effects: Not determined or not applicable. Delayed symptoms and effects: Not determined or not applicable.
Safety Data Sheet According to OSHA Hazard Communication Standard, 29 CFR 1910.1200 Initial preparation date: 02.11.2019 Revision date: 06.07.2023 Page 4 of 11 SECTION 7: Handling and storage Precautions for safe handling: Use only with adequate ventilation. Avoid breathing mist or vapor. Do not eat, drink, smoke or use personal products when handling chemical substances. Conditions for safe storage, including any incompatibilities: Keep container tightly sealed. Protect from freezing and physical damage.
Safety Data Sheet According to OSHA Hazard Communication Standard, 29 CFR 1910.1200 Initial preparation date: 02.11.2019 Revision date: 06.07.2023 Page 5 of 11 If engineering controls do not maintain airborne concentrations below recommended exposure limits (where applicable) or to an acceptable level (in countries where exposure limits have not been established), an approved respirator must be worn. General hygienic measures: Avoid contact with skin, eyes and clothing.
Safety Data Sheet According to OSHA Hazard Communication Standard, 29 CFR 1910.1200 Initial preparation date: 02.11.2019 Revision date: 06.07.2023 Page 6 of 11 Heat. Exposure to moisture. Incompatible materials: Alkalis, isocyanates, oxidizers, Phosphorus compounds, strong acids, strong oxidizing agents. Hazardous decomposition products: None known. SECTION 11: Toxicological information Acute toxicity Assessment: Based on available data, the classification criteria are not met.
Safety Data Sheet According to OSHA Hazard Communication Standard, 29 CFR 1910.1200 Initial preparation date: 02.11.2019 Revision date: 06.07.2023 Page 7 of 11 International Agency for Research on Cancer (IARC): Name Classification Talc Group 3 - Not classifiable as to its carcinogenicity to humans Zeolite Group 3 National Toxicology Program (NTP): None of the ingredients are listed. Germ cell mutagenicity Assessment: Based on available data, the classification criteria are not met.
Safety Data Sheet According to OSHA Hazard Communication Standard, 29 CFR 1910.1200 Initial preparation date: 02.11.2019 Revision date: 06.07.2023 Page 8 of 11 Chronic (long-term) toxicity Assessment: Based on available data, the classification criteria are not met. Product data: No data available. Substance data: No data available. Persistence and degradability Product data: No data available. Substance data: Name Result Piperazine Readily biodegradable in water.
Safety Data Sheet According to OSHA Hazard Communication Standard, 29 CFR 1910.1200 Initial preparation date: 02.11.2019 Revision date: 06.07.
Safety Data Sheet According to OSHA Hazard Communication Standard, 29 CFR 1910.1200 Initial preparation date: 02.11.2019 Revision date: 06.07.2023 Page 10 of 11 280-57-9 1,4-Diazabicyclooctane Not Listed 9082-00-2 Oxirane, 2-methyl-, polymer with oxirane, ether with 1,2,3-propanetriol (3:1) Not Listed 25723-16-4 Propylidynetrimethanol, propoxylated Not Listed 71011-26-2 Quaternary ammonium compounds, benzyl(hydrogenated tallow alkyl)dimethyl, chlorides, compds.
Safety Data Sheet According to OSHA Hazard Communication Standard, 29 CFR 1910.1200 Initial preparation date: 02.11.2019 Revision date: 06.07.
PlasticBonder™ Syringe Tan - Part B J-B Weld Company, LLC Version No: 7.14 Safety Data Sheet according to WHMIS 2015 requirements Issue Date: 10/25/2023 Print Date: 02/07/2024 S.GHS.CAN.
Version No: 7.14 Signal word Page 2 of 10 Issue Date: 10/25/2023 PlasticBonder™ Syringe Tan - Part B Print Date: 02/07/2024 Warning Hazard statement(s) H361 Suspected of damaging fertility or the unborn child. Physical and Health hazard(s) not otherwise classified Not considered hazardous by the OSHA Hazard Communication Standard (29 CFR 1910.1200), Precautionary statement(s) Prevention P201 Obtain special instructions before use. P280 Wear protective gloves and protective clothing.
Version No: 7.14 Page 3 of 10 Issue Date: 10/25/2023 PlasticBonder™ Syringe Tan - Part B Print Date: 02/07/2024 Prevent, by any means available, spillage from entering drains or water courses. When silica dust is dispersed in air, firefighters should wear inhalation protection as hazardous substances from the fire may be adsorbed on the silica particles. When heated to extreme temperatures, (>1700 deg.C) amorphous silica can fuse. Non combustible.
Version No: 7.14 Source Page 4 of 10 Issue Date: 10/25/2023 PlasticBonder™ Syringe Tan - Part B Print Date: 02/07/2024 Ingredient Material name TWA STEL Peak Notes Canada - Prince Edward Island Occupational Exposure Limits Talc Talc - Containing no asbestos fibers 2 mg/m3 Not Available Not Available TLV® Basis: Pulm fibrosis; pulm func Canada - British Columbia Occupational Exposure Limits Talc Talc - Containing asbestos fibres 0.
Version No: 7.14 Page 5 of 10 Issue Date: 10/25/2023 PlasticBonder™ Syringe Tan - Part B Print Date: 02/07/2024 Source Ingredient Material name TWA STEL Peak Notes Canada - British Columbia Occupational Exposure Limits silica amorphous Silica, Amorphous Fume Total 4 mg/m3 Not Available Not Available Not Available Canada - British Columbia Occupational Exposure Limits silica amorphous Silica, Amorphous Fume, Respirable 1.
Version No: 7.14 Page 6 of 10 Issue Date: 10/25/2023 PlasticBonder™ Syringe Tan - Part B Print Date: 02/07/2024 Ingredient TEEL-1 TEEL-2 TEEL-3 piperazine 0.09 ppm 8.
Version No: 7.
Version No: 7.14 Page 8 of 10 Issue Date: 10/25/2023 PlasticBonder™ Syringe Tan - Part B Print Date: 02/07/2024 The material may be irritating to the eye, with prolonged contact causing inflammation. Repeated or prolonged exposure to irritants may produce conjunctivitis. Asthma-like symptoms may continue for months or even years after exposure to the material ends.
Version No: 7.14 Page 9 of 10 Issue Date: 10/25/2023 PlasticBonder™ Syringe Tan - Part B Print Date: 02/07/2024 Persistence and degradability Ingredient Persistence: Water/Soil Persistence: Air piperazine LOW LOW silica amorphous LOW LOW Bioaccumulative potential Ingredient Bioaccumulation piperazine LOW (BCF = 3.9) silica amorphous LOW (LogKOW = 0.5294) Mobility in soil Ingredient Mobility piperazine LOW (KOC = 52.71) silica amorphous LOW (KOC = 23.
Version No: 7.
PlasticBonder™ Syringe Tan - Part B J-B Weld Company, LLC Version Num: 7.14 Fiche de données de sécurité selon les exigences du SIMDUT 2015 Date d'émission: 10/25/2023 Date d’impression: 02/07/2024 S.GHS.CAN.
Version Num: 7.14 Page 2 de 11 PlasticBonder™ Syringe Tan - Part B Date d'émission: 10/25/2023 Date d’impression: 02/07/2024 Pictogramme(s) de danger Mention d’avertissement Attention Déclaration(s) sur les risques H361 Susceptible de nuire à la fertilité ou au fœtus. Danger physique et risque pour la santé non classé ailleurs N'est pas applicable Déclarations de Sécurité: Prévention P201 Se procurer les instructions avant utilisation.
Version Num: 7.14 Page 3 de 11 Date d'émission: 10/25/2023 Date d’impression: 02/07/2024 PlasticBonder™ Syringe Tan - Part B Équipement de protection spécial et précautions particulières pour les pompiers Appelez les pompiers et indiquez-leur le lieu et la nature du risque. Mettez un appareil respiratoire et des gants de protection conçus pour lutter contre le feu. Empêcher, par tous les moyens disponibles, que les déversements ne pénètrent dans les égouts ou les cours d'eau.
Version Num: 7.14 Page 4 de 11 Date d'émission: 10/25/2023 Date d’impression: 02/07/2024 PlasticBonder™ Syringe Tan - Part B Source Composant Nom du produit VME STEL pic Notes Canada - Colombie-Britannique Limites D'Exposition Professionnelle Talc Talc - Containing asbestos fibres 0.1 f/cc Pas Disponible Pas Disponible (K) - should not exceed 2 mg/m3 respirable particulate.
Version Num: 7.
Version Num: 7.
Version Num: 7.14 Page 7 de 11 Date d'émission: 10/25/2023 Date d’impression: 02/07/2024 PlasticBonder™ Syringe Tan - Part B Mesures de protection individuelle, telles que les équipements de protection individuelle Protection des yeux/du visage. Protection de la peau Protection des mains / pieds Protection corporelle Autres protections Lunettes de sécurité avec protections latérales Lunettes chimiques. [AS/NZS 1337.
Version Num: 7.14 Page 8 de 11 Date d'émission: 10/25/2023 Date d’impression: 02/07/2024 PlasticBonder™ Syringe Tan - Part B Contact avec la peau Yeux Chronique PlasticBonder™ Syringe Tan Part B Talc Un contact de la peau n'est pas connu pour avoir des effets nocifs sur la santé (classifié comme tel par la directive CE); le produit peut néanmoins produire des dommages sur la santé après une entrée par des blessures, des lésions ou des abrasions.
Version Num: 7.
Version Num: 7.14 Page 10 de 11 PlasticBonder™ Syringe Tan - Part B Date d'émission: 10/25/2023 Date d’impression: 02/07/2024 SECTION 13 Considérations relatives à l’élimination Méthodes de traitement des déchets Elimination du produit / emballage Recycler si possible ou consulter le fabricant pour les options de recyclage. Consulter l'Autorité de regulation des déchets pour un traitement. Recycler les containers si possible ou en disposer dans un lieu autorisé.
Version Num: 7.14 Page 11 de 11 PlasticBonder™ Syringe Tan - Part B Date d'émission: 10/25/2023 Date d’impression: 02/07/2024 Inventaire national Statut Australie - AIIC / Australie non-utilisation industrielle Oui Canada - DSL Oui Canada - NDSL Non (Talc; pipérazine) Chine - IECSC Oui Europe - EINEC / ELINCS / NLP Oui Japon - ENCS Oui Corée - KECI Oui Nouvelle-Zélande - NZIoC Oui Philippines - PICCS Oui É.-U.A.
PlasticBonder™ Syringe Black - Part A J-B Weld Company LLC Version No: 11.16 Safety Data Sheet according to OSHA HazCom Standard (2012) requirements Issue Date: 12/07/2023 Print Date: 12/07/2023 S.GHS.USA.
Version No: 11.16 Page 2 of 14 PlasticBonder™ Syringe Black - Part A H319 Causes serious eye irritation. H332 Harmful if inhaled. H334 May cause allergy or asthma symptoms or breathing difficulties if inhaled. H335 May cause respiratory irritation. H351 Suspected of causing cancer. H373 May cause damage to organs through prolonged or repeated exposure.
Version No: 11.16 Page 3 of 14 PlasticBonder™ Syringe Black - Part A Issue Date: 12/07/2023 Print Date: 12/07/2023 Description of first aid measures Eye Contact If this product comes in contact with the eyes: Wash out immediately with fresh running water. Ensure complete irrigation of the eye by keeping eyelids apart and away from eye and moving the eyelids by occasionally lifting the upper and lower lids. Seek medical attention without delay; if pain persists or recurs seek medical attention.
Version No: 11.16 Page 4 of 14 PlasticBonder™ Syringe Black - Part A Issue Date: 12/07/2023 Print Date: 12/07/2023 Treatment for asthma includes inhaled sympathomimetics (epinephrine [adrenalin], terbutaline) and steroids. Activated charcoal (1 g/kg) and a cathartic (sorbitol, magnesium citrate) may be useful for ingestion. Mydriatics, systemic analgesics and topical antibiotics (Sulamyd) may be used for corneal abrasions. There is no effective therapy for sensitised workers.
Version No: 11.16 Page 5 of 14 Issue Date: 12/07/2023 Print Date: 12/07/2023 PlasticBonder™ Syringe Black - Part A DO NOT allow clothing wet with material to stay in contact with skin Other information Consider storage under inert gas. for commercial quantities of isocyanates: · Isocyanates should be stored in adequately bunded areas. Nothing else should be kept within the same bunding. Pre-polymers need not be segregated. Store in original containers. Keep containers securely sealed.
Version No: 11.
Version No: 11.16 Page 7 of 14 Issue Date: 12/07/2023 Print Date: 12/07/2023 PlasticBonder™ Syringe Black - Part A Hands/feet protection NOTE: The material may produce skin sensitisation in predisposed individuals. Care must be taken, when removing gloves and other protective equipment, to avoid all possible skin contact. Contaminated leather items, such as shoes, belts and watch-bands should be removed and destroyed.
Version No: 11.16 Page 8 of 14 Issue Date: 12/07/2023 Print Date: 12/07/2023 PlasticBonder™ Syringe Black - Part A Vapour density (Air = 1) >1 VOC g/L Not Available SECTION 10 Stability and reactivity Reactivity See section 7 Unstable in the presence of incompatible materials. Product is considered stable. Hazardous polymerisation will not occur. Presence of elevated temperatures.
Version No: 11.
Version No: 11.16 Page 10 of 14 Issue Date: 12/07/2023 Print Date: 12/07/2023 PlasticBonder™ Syringe Black - Part A Attention should be paid to atopic diathesis, characterised by increased susceptibility to nasal inflammation, asthma and eczema. Exogenous allergic alveolitis is induced essentially by allergen specific immune-complexes of the IgG type; cell-mediated reactions (T lymphocytes) may be involved. Such allergy is of the delayed type with onset up to four hours following exposure.
Version No: 11.16 Page 11 of 14 Issue Date: 12/07/2023 Print Date: 12/07/2023 PlasticBonder™ Syringe Black - Part A Endpoint Test Duration (hr) Species Value Source EC50 96h Algae or other aquatic plants 7202.7mg/l 2 LC50 96h Fish 89581.016mg/l 2 NOEC(ECx) 720h Algae or other aquatic plants 918.
Version No: 11.16 Page 12 of 14 Issue Date: 12/07/2023 PlasticBonder™ Syringe Black - Part A Print Date: 12/07/2023 Legislation addressing waste disposal requirements may differ by country, state and/ or territory. Each user must refer to laws operating in their area. In some areas, certain wastes must be tracked. DO NOT allow wash water from cleaning or process equipment to enter drains. It may be necessary to collect all wash water for treatment before disposal.
Version No: 11.16 Page 13 of 14 Issue Date: 12/07/2023 PlasticBonder™ Syringe Black - Part A International Agency for Research on Cancer (IARC) - Agents Classified by the IARC Monographs - Not Classified as Carcinogenic International WHO List of Proposed Occupational Exposure Limit (OEL) Values for Manufactured Nanomaterials (MNMS) US - Alaska Air Quality Control - Concentrations Triggering an Air Quality Episode for Air Pollutants Other Than PM-2.
Version No: 11.16 Page 14 of 14 Issue Date: 12/07/2023 Print Date: 12/07/2023 PlasticBonder™ Syringe Black - Part A US. EPA CERCLA Hazardous Substances and Reportable Quantities (40 CFR 302.4) Name Reportable Quantity in Pounds (lb) Reportable Quantity in kg 4,4'-diphenylmethane diisocyanate (MDI) 5000 2270 US.
PlasticBonder™ Syringe Black - Part A J-B Weld Company, LLC Version No: 11.16 Safety Data Sheet according to WHMIS 2015 requirements Issue Date: 12/07/2023 Print Date: 12/07/2023 S.GHS.CAN.
Version No: 11.16 Page 2 of 16 PlasticBonder™ Syringe Black - Part A Signal word Issue Date: 12/07/2023 Print Date: 12/07/2023 Danger Hazard statement(s) H302 Harmful if swallowed. H315 Causes skin irritation. H317 May cause an allergic skin reaction. H319 Causes serious eye irritation. H332 Harmful if inhaled. H334 May cause allergy or asthma symptoms or breathing difficulties if inhaled. H335 May cause respiratory irritation. H351 Suspected of causing cancer.
Version No: 11.16 Page 3 of 16 PlasticBonder™ Syringe Black - Part A Issue Date: 12/07/2023 Print Date: 12/07/2023 Description of first aid measures Eye Contact If this product comes in contact with the eyes: Wash out immediately with fresh running water. Ensure complete irrigation of the eye by keeping eyelids apart and away from eye and moving the eyelids by occasionally lifting the upper and lower lids. Seek medical attention without delay; if pain persists or recurs seek medical attention.
Version No: 11.16 Page 4 of 16 PlasticBonder™ Syringe Black - Part A Issue Date: 12/07/2023 Print Date: 12/07/2023 There is no effective therapy for sensitised workers. [Ellenhorn and Barceloux; Medical Toxicology] NOTE: Isocyanates cause airway restriction in naive individuals with the degree of response dependant on the concentration and duration of exposure. They induce smooth muscle contraction which leads to bronchoconstrictive episodes.
Version No: 11.16 Page 5 of 16 Issue Date: 12/07/2023 Print Date: 12/07/2023 PlasticBonder™ Syringe Black - Part A Other information Consider storage under inert gas. for commercial quantities of isocyanates: · Isocyanates should be stored in adequately bunded areas. Nothing else should be kept within the same bunding. Pre-polymers need not be segregated. Store in original containers. Keep containers securely sealed. No smoking, naked lights or ignition sources.
Version No: 11.16 Page 6 of 16 Issue Date: 12/07/2023 Print Date: 12/07/2023 PlasticBonder™ Syringe Black - Part A Source Ingredient Material name TWA STEL Peak Notes Not Available Not Available EM: A substance to which exposure must be reduced to a minimum S: SENSITIZER Canada - Quebec Permissible Exposure Values for Airborne Contaminants 4,4'-diphenylmethane diisocyanate (MDI) Methylene bis (4-phenyl isocyanate) (MDI) 0.005 ppm / 0.
Version No: 11.16 Page 7 of 16 Issue Date: 12/07/2023 Print Date: 12/07/2023 PlasticBonder™ Syringe Black - Part A Source Ingredient Material name TWA STEL Peak Notes Canada - British Columbia Occupational Exposure Limits Talc Talc - Containing asbestos fibres 0.1 f/cc Not Available Not Available (K) - should not exceed 2 mg/m3 respirable particulate.
Version No: 11.16 Page 8 of 16 Issue Date: 12/07/2023 Print Date: 12/07/2023 PlasticBonder™ Syringe Black - Part A Source Ingredient Material name TWA STEL Peak Notes Canada - British Columbia Occupational Exposure Limits silica amorphous Silica, Amorphous Diatomaceous earth (uncalcined), Respirable 1.
Version No: 11.
Version No: 11.16 Page 10 of 16 Issue Date: 12/07/2023 Print Date: 12/07/2023 PlasticBonder™ Syringe Black - Part A Other protection All employees working with isocyanates must be informed of the hazards from exposure to the contaminant and the precautions necessary to prevent damage to their health.
Version No: 11.16 Page 11 of 16 Issue Date: 12/07/2023 Print Date: 12/07/2023 PlasticBonder™ Syringe Black - Part A Incompatible materials See section 7 Hazardous decomposition products See section 5 SECTION 11 Toxicological information Information on toxicological effects Inhaled The material can cause respiratory irritation in some persons. The body's response to such irritation can cause further lung damage.
Version No: 11.16 Page 12 of 16 Issue Date: 12/07/2023 Print Date: 12/07/2023 PlasticBonder™ Syringe Black - Part A Dermal (rabbit) LD50: >2000 mg/kg[2] Not Available Inhalation(Rat) LC50: >0.5 mg/l4h[2] Oral (Rat) LD50: >2000 mg/kg[1] Talc TOXICITY IRRITATION dermal (rat) LD50: >2000 mg/kg[1] Eye: no adverse effect observed (not irritating)[1] Inhalation(Rat) LC50: >2.
Version No: 11.16 Page 13 of 16 Issue Date: 12/07/2023 Print Date: 12/07/2023 PlasticBonder™ Syringe Black - Part A HOMOPOLYMER 4,4'-DIPHENYLMETHANE DIISOCYANATE (MDI) & MDI HOMOPOLYMER & MDI, PROPYLENE GLYCOL, TRIMETHYLOLPROPANE,TRIETHER & SILICA AMORPHOUS 4,4'-DIPHENYLMETHANE DIISOCYANATE (MDI) & PROPYLENE CARBONATE MDI, PROPOXYLATED & MDI, PROPYLENE GLYCOL, TRIMETHYLOLPROPANE,TRIETHER The substance is classified by IARC as Group 3: NOT classifiable as to its carcinogenicity to humans.
Version No: 11.16 Page 14 of 16 Issue Date: 12/07/2023 Print Date: 12/07/2023 PlasticBonder™ Syringe Black - Part A propylene carbonate Legend: EC50 48h Crustacea >86mg/l 2 EC50 96h Algae or other aquatic plants 217.576mg/l 2 LC50 96h Fish 1033.
Version No: 11.16 Page 15 of 16 Issue Date: 12/07/2023 PlasticBonder™ Syringe Black - Part A Print Date: 12/07/2023 Sea transport (IMDG-Code / GGVSee): NOT REGULATED FOR TRANSPORT OF DANGEROUS GOODS 14.7.1. Transport in bulk according to Annex II of MARPOL and the IBC code Not Applicable 14.7.2.
Version No: 11.
PlasticBonder™ Syringe Black - Part A J-B Weld Company, LLC Version Num: 11.16 Fiche de données de sécurité selon les exigences du SIMDUT 2015 Date d'émission: 12/07/2023 Date d’impression: 12/07/2023 S.GHS.CAN.
Version Num: 11.16 Page 2 de 17 PlasticBonder™ Syringe Black - Part A Date d'émission: 12/07/2023 Date d’impression: 12/07/2023 Éléments d’étiquetage Pictogramme(s) de danger Mention d’avertissement Danger Déclaration(s) sur les risques H302 Nocif en cas d'ingestion. H315 Provoque une irritation cutanée. H317 Peut provoquer une allergie cutanée. H319 Provoque une sévère irritation des yeux. H332 Nocif par inhalation.
Version Num: 11.
Version Num: 11.16 Page 4 de 17 PlasticBonder™ Syringe Black - Part A Date d'émission: 12/07/2023 Date d’impression: 12/07/2023 Indication des éventuels soins médicaux immédiats et traitements particuliers nécessaires Traiter symptomatiquement. Pour des expositions chroniques et sous-chroniques aux isocyanates: Le produit peut être un sensibilisateur pulmonaire potentiel qui provoque des spasmes de bronches même chez les patients sans hyperactivité respiratoire antérieure.
Version Num: 11.16 Page 5 de 17 Date d'émission: 12/07/2023 Date d’impression: 12/07/2023 PlasticBonder™ Syringe Black - Part A Risque modéré. Vider la zone de son personnel et se déplacer contre le vent. Alerter les pompiers et leurs indiquer l'endroit et la nature du risque. Le conseil sur l'équipement de protection individuel est contenu dans la rubrique 8 de la FDS.
Version Num: 11.16 Page 6 de 17 Date d'émission: 12/07/2023 Date d’impression: 12/07/2023 PlasticBonder™ Syringe Black - Part A Source Composant Nom du produit VME STEL pic Notes Canada - Limites d'exposition professionnelle de l'Alberta 1,1'-METHANEDIYLBIS(4ISOCYANATOBENZENE) Methylene bisphenyl isocyanate (Diphenylmethane4,4’-diisocyanate; MDI) 0.005 ppm / 0.
Version Num: 11.
Version Num: 11.
Version Num: 11.
Version Num: 11.16 Page 10 de 17 Date d'émission: 12/07/2023 Date d’impression: 12/07/2023 PlasticBonder™ Syringe Black - Part A Composant Note de la bande d'exposition professionnelle Limite de bande d'exposition professionnelle Diisocyanate de 4,4'-méthylènediphényle homopolymérisé E ≤ 0.1 ppm MDI, propylene glycol, trimethylolpropane,triether E ≤ 0.01 mg/m³ carbonate de propylènee E ≤ 0.
Version Num: 11.
Version Num: 11.16 Page 12 de 17 Date d'émission: 12/07/2023 Date d’impression: 12/07/2023 PlasticBonder™ Syringe Black - Part A Les personnes avec un historique d'asthme ou d'autres problèmes respiratoires ou qui sont connus comme étant sensibilisées ne devraient pas être engagées dans des travaux impliquant la manipulation d'isocyanates.
Version Num: 11.
Version Num: 11.
Version Num: 11.16 Page 15 de 17 PlasticBonder™ Syringe Black - Part A Composant Mobilité 1,1'-METHANEDIYLBIS(4ISOCYANATOBENZENE) BAS (KOC = 376200) silane,-dichlorodiméthyl-,produits-de-réaction-avec-lasilice BAS (KOC = 23.74) carbonate de propylènee BAS (KOC = 14.
Version Num: 11.
Version Num: 11.
