SDS

Other protection
All employees working with isocyanates must be informed of the hazards from exposure to the contaminant and the precautions necessary to
prevent damage to their health. They should be made aware of the need to carry out their work so that as little contamination as possible is
produced, and of the importance of the proper use of all safeguards against exposure to themselves and their fellow workers. Adequate training,
both in the proper execution of the task and in the use of all associated engineering controls, as well as of any personal protective equipment, is
essential.
Overalls.
P.V.C apron.
Barrier cream.
Type A-P Filter of sufficient capacity. (AS/NZS 1716 & 1715, EN 143:2000 & 149:2001, ANSI Z88 or national equivalent)
Cartridge respirators should never be used for emergency ingress or in areas of unknown vapour concentrations or oxygen content.
The wearer must be warned to leave the contaminated area immediately on detecting any odours through the respirator. The odour may indicate that the mask is not functioning
properly, that the vapour concentration is too high, or that the mask is not properly fitted. Because of these limitations, only restricted use of cartridge respirators is considered
appropriate.
Cartridge performance is affected by humidity. Cartridges should be changed after 2 hr of continuous use unless it is determined that the humidity is less than 75%, in which case,
cartridges can be used for 4 hr. Used cartridges should be discarded daily, regardless of the length of time used
For spraying or operations which might generate aerosols:
Full face respirator with supplied air.
In certain circumstances, personal protection of the individual employee is necessary. Personal protective devices should be regarded as being supplementary to substitution and
engineering control and should not be used in preference to them as they do nothing to eliminate the hazard.
However, in some situations, minimising exposure to isocyanates by enclosure and ventilation is not possible, and occupational exposure standards may be exceeded, particularly
during on-site mixing of paints, spray-painting, foaming and maintenance of machine and ventilation systems. In these situations, air-line respirators or self-contained breathing
apparatus complying with the appropriate nationals standard must be used.
Organic vapour respirators with particulate pre- filters and powered, air-purifying respirators are NOT suitable.
Personal protective equipment must be appropriately selected, individually fitted and workers trained in their correct use and maintenance. Personal protective equipment must be
regularly checked and maintained to ensure that the worker is being protected.
Air- line respirators or self-contained breathing apparatus complying with the appropriate national standard should be used during the clean-up of spills and the repair or clean-up
of contaminated equipment and similar situations which cause emergency exposures to hazardous atmospheric concentrations of isocyanate.
SECTION 9 Physical and chemical properties
Information on basic physical and chemical properties
Appearance
Off-White Liquid
Physical state
Liquid
Relative density (Water = 1)
1.288
Odour
Not Available
Partition coefficient n-octanol
/ water
Not Available
Odour threshold
Not Available
Auto-ignition temperature (°C)
Not Available
pH (as supplied)
Not Available
Decomposition
temperature (°C)
Not Available
Melting point / freezing point
(°C)
Not Available
Viscosity (cSt)
Not Available
Initial boiling point and boiling
range (°C)
200
Molecular weight (g/mol)
Not Available
Flash point (°C)
100
Taste
Evaporation rate
<1
Explosive properties
Not Available
Flammability
Not Applicable
Oxidising properties
Not Available
Upper Explosive Limit (%)
Not Available
Surface Tension (dyn/cm or
mN/m)
Not Available
Lower Explosive Limit (%)
Not Available
Volatile Component (%vol)
Not Available
Vapour pressure (kPa)
<0.013
Gas group
Not Available
Solubility in water
Immiscible
pH as a solution (1%)
Not Available
Vapour density (Air = 1)
>1
VOC g/L
Not Available
SECTION 10 Stability and reactivity
Reactivity
See section 7
Chemical stability
Unstable in the presence of incompatible materials.
Product is considered stable.
Hazardous polymerisation will not occur.
Presence of elevated temperatures.
Possibility of hazardous
reactions
See section 7
Conditions to avoid
See section 7
Version No:
11.16
Page
10
of
16
PlasticBonder™ Syringe Black - Part A
Issue Date:
12/07/2023
Print Date:
12/07/2023
Continued...