Product Manual

ManualsBrandsJ&D Mfg. ManualsAgricultural FansJ & D Mfg. EZ Breeze Basket Fan — 16in. Dia., 1620 CFM, 1/10 HP, 115 Volt

(1) 3/8"

Nylock Nut

(1) 3/8" x 1-1/4"

Hex Bolt

(2) 3/8"

Flat Washer

(1) 1/4"

Nylock Nut

(1) 1/4" x 1"

Hex Bolt

(2) 1/4"

Flat Washer

Safety Glasses

Measuring Tape

Socket Wrench

Combination Wrenches

7/16” & 9/16”

7/16” & 9/16” Sockets

PARTS LEGEND

Bracket

Flag

Motor

Flag

Capacitor

BARNSTORMER, GREEN BREEZE,

EZ-BREEZE, AND HIGH OUTPUT

DELUXE BASKET FAN

Please read over all instructions carefully before you

begin. If you have any questions please call your local

dealer, or contact J&D Manufacturing at 1-800-998-2398.

RECOMMENDED TOOLS FOR ASSEMBLY (NOT PROVIDED)

INCLUDED ASSEMBLY HARDWARE - TO SCALE

WARRANTY

J&D Manufacturing warrants all products are free from defects in materials

and workmanship under normal use for the period of one year from date of

purchase. Our warranty does not cover normal or regular wear and tear.

J&D Manufacturing can repair or replace at our option, any product or part

of the product that is found to be defective. Our warranty applies to

materials only, and does not include return freight, delivery, loss or damage

to personal property, cost of removal or installation, any incidental or

consequential damages or labor. This warranty does not apply to products

which are misused, abused, altered, improperly installed or subject to

negligence. All warranties must be approved through our warranty

department. The original purchaser must present a copy of the invoice for

the defective product. One year is our standard warranty unless specified

on our literature or in the installation instructions or user manuals.

INSTALLATION

IS123-11I J&D Manufacturing • 6200 Hwy 12 • Eau Claire, WI 54701 • 1-800-998-2398 • www.jdmfg.com Page 1 of 4

Green Breeze and EZ-Breeze models include additional mounting hardware.

See page 4 for further information and instructions.

Summary of content (4 pages)

PAGE 1
BARNSTORMER, GREEN BREEZE, EZ-BREEZE, AND HIGH OUTPUT DELUXE BASKET FAN INCLUDED ASSEMBLY HARDWARE - TO SCALE (2) 1/4" Flat Washer (2) 3/8" Flat Washer (1) 3/8" x 1-1/4" Hex Bolt (1) 1/4" x 1" Hex Bolt (1) 1/4" Nylock Nut (1) 3/8" Nylock Nut Green Breeze and EZ-Breeze models include additional mounting hardware. See page 4 for further information and instructions.
PAGE 2
It is important to select a proper location when mounting your circulation fan. You must provide a minimum of 5’ unrestricted air flow on the back side of the fan. Failure to provide the space needed for airflow may reduce motor life and void the warranty. 1 Attach fan to bracket. Insert bracket flag in between the motor flags and secure using the center holes on the motor flags with (1) 3/8” x 1-1/4 hex bolt, (2) 3/8” washers and (1) 3/8” nylock nut as shown in step 4a.
PAGE 3
ADDITIONAL CLARIFICATIONS AND WARNINGS Do NOT operate fan with the motor mounted at an angle larger than 60º from horizontal. This will void the warranty. Do NOT mount fan with capacitor on the bottom. This can cause moisture to build up in the capacitor cap and short out the capacitor. Mounting the fan this way will void the warranty. Maximum 60º angle Capacitor Do NOT mount bracket horizontally.
PAGE 4
ADDITIONAL INCLUDED HARDWARE FOR THE GREEN BREEZE AND EZ-BREEZE FANS - TO SCALE (2) 5/16” x 2-1/2”ID U-Bolt PROVIDING POWER TO FAN Instructions for corded models • Provide a grounded outlet that meets or exceeds the load capability for your fan. Wiring instructions for non corded models • Wiring should only be performed by a trained electrician to prevent injury or death. • Install manual disconnect switch inside building adjacent to fan. • Route wire to motor with drip loop and secure.