Product Manual A

ManualsBrandsJ&D Mfg. ManualsEnclosed Exhaust FansJ & D Mfg. Wallmaster Exhaust Fan — 36in. Dia., 1/2 HP, 10,000 CFM, Three-Phase Motor, 3 Wing Blade

IS276-17I

J&D Manufacturing • 6200 Hwy 12 • Eau Claire, WI 54701 • 1-800-998-2398 • www.jdmfg.com

Page 1/3

WALL MASTER EXHAUST FAN

J&D Mfg. warrants all products are free from defects in materials and workmanship under

normal use for the period of one year from date of purchase and our warranty does not cover

normal or regular wear and tear. J&D Mfg can repair or replace at our option, any product or

part of the product that is found to be defective. Our warranty applies to materials only and

does not include return freight, delivery, loss or damage to personal property, cost of removal

or installation, any incidental or consequential damages or labor. This warranty does not apply

to products which are misused, abused, altered, improperly installed or subject to negligence.

All warranties must be approved through our warranty department. The original purchaser

must present a copy of the invoice for the defective product. One year is our standard

warranty unless specified on our literature or in the installation instructions/user manuals.

INSTALLATION HARDWARE IS NOT PROVIDED

Please read over all instructions carefully before you

begin. If you have any questions please call your local

dealer, or contact J&D Manufacturing at 1-800-998-2398.

Safety Glasses

RECOMMENDED TOOLS FOR ASSEMBLY (NOT PROVIDED)

ADDITIONAL TOOLS (NOT PROVIDED) DEPENDENT ON BUILDING MATERIAL

AND CHOSEN HARDWARE WILL BE NEEDED FOR INSTALLATION

WARRANTY

INSTALLATION

For 36” models construct structurally sound 41” square rough opening.

For 50“ models construct structurally sound 54¾” square rough opening.

41”

ROUGH

OPENING

(Inside Dimensions)

36”

Wall Master

Models

54¾”

ROUGH

OPENING

(Inside Dimensions)

50”

Wall Master

Models

The top of each wall master is indicated by the location of the J&D label on

the sides of the fan. Do not mount unit in any position but upright as shown

below.

NOTE: Depth of fans is indicated only for clearance purposes and does not

indicate depth of rough opening.

14¼”

Depth of 36” Direct Drive

Wall Master Models

23¾”

Depth of 36” & 50” Belt Drive

Wall Master Models

#2 Square Drive Bit & Drill

Location of J&D

label indicates

the top of the fan

Location of J&D

label indicates

the top of the fan

Summary of content (3 pages)

PAGE 1
WALL MASTER EXHAUST FAN For 36” models construct structurally sound 41” square rough opening. For 50“ models construct structurally sound 54¾” square rough opening. 54¾” 41” ROUGH OPENING 41” ROUGH OPENING (Inside Dimensions) 36” Wall Master Models 54¾” 1 (Inside Dimensions) 50” Wall Master Models The top of each wall master is indicated by the location of the J&D label on the sides of the fan. Do not mount unit in any position but upright as shown below.
PAGE 2
Using a #2 square drive bit remove and set aside rear guard and clips. The wall master fan can be mounted flush to interior as shown in Step 4a, flush with exterior as shown in Step 4b, or any location in-between as shown split in Step 4c. NOTE: It is recommended that the exterior exposed top of the unit as shown in Step 4a and 4c be protected from collecting rain water and especially snow and ice. Damage to the unit due to inadequate protection is not covered by warranty.
PAGE 3
Using a minimum of 12 fasteners suitable to your structure secure the unit in the opening as shown below, 3 fasteners per side. Using a #2 square drive bit reinstall the rear guard and clips that were removed in Step 3. 5 ! DISCONNECT POWER BEFORE INSTALLING OR SERVICING. ! ALL ELECTRICAL WORK SHOULD BE COMPLETED BY QUALIFIED PERSONNEL AND MEET NATIONAL (NEC), REGIONAL AND LOCAL ELECTRIC CODES. Connecting Power To The Unit • Install manual disconnect switch inside building adjacent to fan.